Page 3
IMPORTANT WARNING W A R N I N G KEEP THESE INSTRUCTIONS IN A SAFE PLACE WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse of the appliance, please read these instructions carefully and follow them strictly.
Scraper arm (Blixer only) ® INTRODUCTION TO YOUR NEW BLIXER OR A ® • Blades CUTTER MIXER R 8 • R 10 • R 15 • R 20 • • Seal Blixer 8 • Blixer 10 • Blixer 15 • Blixer ®...
Page 5
ROBOT COUPE U.S.A., INC. ONE YEAR LIMITED WARRANTY THE FOLLOWING ARE NOT Charges to change Direction-of-Rotation YOUR NEW ROBOT COUPE PRODUCT of Three Phase electric motors (INSTALLER IS COVERED UNDER WARRANTY: IS WARRANTED TO THE ORIGINAL RESPONSIBLE). All Robot Coupe products must PURCHASER FOR A PERIOD OF ONE operate counter-clock-wise.
IMPORTANT WARNING W A R N I N G KEEP THESE INSTRUCTIONS IN A SAFE PLACE WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse of the appliance, please read these instructions carefully and follow them strictly.
• Blixer 15 • Blixer ® ® bowl on the motor shaft Three phase R 8 • R 10 • R 15 • R 20 so that the handle on your Blixer 8 • Blixer 10 • Blixer 15 • Blixer ®...
Page 8
USES & EXAMPLES • If the lid parts are already assembled: W A R N I N G 4) Place the lid assembly in • CUTTER There is a green safety indicator light on the the correction position. control panel of the motor unit. If this green Max processing quantity (in pounds) Next, insert the metal pin as USES...
Repeat this pulsing action, allowing the - Stop the unit, open the lid and add water and salt Optional extra: 3.5-litre mini bowl for the R 8 blade to stop each time, until the desired cut is (needs about 20 seconds), achieved.
, patented As a precaution, always unplug your appliance 1) Place the mini bowl over by ROBOT COUPE on to the lid and connect it to a before cleaning it (hazard of electrocution) and the chimney of the large vacuum pump (see instructions page 13).
¼ turn. It can then be lifted • DISMANTLING THE BLADE ASSEMBLY vertically from the motor support. If the bowl contains R 8 • R 10 • R 15 • R 20 • Blixer 8 • Blixer ®...
• MINI BOWL BLADE (Cutter only) • BLADES DIAGNOSTIC SYSTEM A special tool designed to Only the blades on cutters R 8/R 10/R 15 and R 20 R E M E M B E R make it easier to remove can be sharpened.
Page 13
1) No light When none of the buttons is being pressed, the light - If the test sequence reveals a problem with one of the presence sensors, check that the removable parts flashes to indicate the current testing level. This means that either your appliance is switched off of your cutter mixer (bowl, lid and arm) are all in or there is a problem with the power supply.
OPERATING INSTRUCTIONS FOR THE VACUUM KIT R-VAC (Cutter only) ® 1° ASSEMBLING THE VACUUM KIT R-VAC ® - Insert filter N° 2 into body N° 3 - Screw part N° 1 onto body N° 3 (the tube is fed through body N° 3). 2°...
FITTING AND USING THE BLADE ASSEMBLY Plastic Narrow Blade Screw Blade Long ring ring spacer support (Cutter only) • 2-BLADE ASSEMBLY: • 3-BLADE ASSEMBLY: We recommend you use the two-blade assembly for processing small We recommend you use the 3-blade assembly for processing large quantities of more than half the amounts (less than half the maximum capacity indicated on page 7).
Page 16
FITTING AND USING THE BLADE ASSEMBLY Plastic Narrow Blade Screw Blade Long ring ring spacer shaft (Blixer only) ® • 2-BLADE ASSEMBLY: • 3-BLADE ASSEMBLY (except for the Blixer ® We recommend you use the two-blade assembly for processing We recommend you use the 3-blade assembly for processing large quantities of more than half small amounts.
12 ¾ 12 ¾ 14 R 20 This ROBOT COUPE range of Cutter and Blixer ® If you wish your unit to be serviced at the factory, equipped with a mechanical safety system and •...