Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Version 1.0
Published March 2013
Copyright©2013 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners' benefit, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for a particular
purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
TM
The terms HDMI
and HDMI High-Definition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
"Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate"
ASRock Website: http://www.asrock.com
Advertisement
Table of Contents
Related Manuals for ASROCK H87M Pro4/ASM
Summary of Contents for ASROCK H87M Pro4/ASM
- Page 1 (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
- Page 2 If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply) The terms HDMI™...
- Page 3 Supplies Guaranteed for One Year ASRock guarantees immediate brand new replacement from distributors, shipped prior to the return of the defective items with absolutely no questions asked during the first 30 days. Immediate new or buffer replacement from distributors depending on their inventory’s availability for the next 11 months.
-
Page 4: Motherboard Layout
H87M Pro4/ASM Motherboard Layout PWR_FAN1 CPU_FAN1 ATX12V1 CPU_FAN2 Fast RAM USB 3.0 T: USB2 B: USB3 USB 3.0 Top: T: USB4 RJ-45 B: USB5 HD_AUDIO1 CHA_FAN2 CLRCMOS1 SPDIF1_OUT1 CMOS Battery Audio CODEC PCI Express 3.0 PCIE1 Intel PCI1 RoHS PCI2... - Page 5 No. Description Power Fan Connector (PWR_FAN1) CPU Fan Connector (CPU_FAN2) CPU Fan Connector (CPU_FAN1) ATX 12V Power Connector (ATX12V1) 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_B1) 2 x 240-pin DDR3 DIMM Slots (DDR3_A2, DDR3_B2) ATX Power Connector (ATXPWR1) USB 3.0 Header (USB10_11) SATA3 Connectors (SATA_4_5) SATA3 Connectors (SATA_2_3) SATA3 Connectors (SATA_0_1)
- Page 6 H87M Pro4/ASM I/O Panel No. Description No. Description USB 2.0 Ports (USB01) Microphone (Pink) D-Sub Port Optical SPDIF Out Port LAN RJ-45 Port* USB 3.0 Ports (USB_45) Central / Bass (Orange) USB 3.0 Ports (USB_23) Rear Speaker (Black) HDMI Port...
- Page 7 * There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications. ACT/LINK LED SPEED LED LAN Port Activity / Link LED Speed LED Status Description Status Description No Link 10Mbps connection Blinking Data Activity Orange...
-
Page 8: Chapter 1 Introduction
ASRock’s website without further notice. If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. You may find the latest VGA cards and CPU support list on ASRock’s website as well. ASRock website http://www.asrock.com. -
Page 9: Expansion Slot
1.2 Specifications Platform • Micro ATX Form Factor • All Solid Capacitor design • Supports 4 Generation Intel® Core i7 / i5 / i3 / Xeon® / Pentium® / Celeron® in LGA1150 Package • Digi Power Design • 4 Power Phase Design • Supports Intel®... - Page 10 H87M Pro4/ASM • Supports Triple Monitors • Supports HDMI Technology with max. resolution up to 1920x1200 @ 60Hz • Supports DVI-D with max. resolution up to 1920x1200 @ 60Hz • Supports D-Sub with max. resolution up to 1920x1200 @ 60Hz • Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and...
-
Page 11: Hardware Monitor
Storage • 6 x SATA3 6.0 Gb/s connectors, support RAID (RAID 0, RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology 12 and Intel Smart Response Technology), NCQ, AHCI and “Hot Plug” Connector • 1 x IR header • 1 x Print Port header • 1 x COM port header • 1 x Chassis Intrusion header • 1 x TPM header... - Page 12 Due to limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 32-bit operating systems. Windows® 64-bit operat- ing systems do not have such limitations. You can use ASRock XFast RAM to utilize the memory that Windows® cannot use.
-
Page 13: Unique Features
LED, FAN-Tastic Tuning, OC Tweaker and a whole lot more. ASRock Instant Flash ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM. This conve- nient BIOS update tool allows you to update the system BIOS in a few clicks without preparing an additional floppy diskette or other complicated flash utility. - Page 14 And it also boosts the speed of Adobe Photoshop 5 times faster. Another advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifespan.
- Page 15 Windows® 8 brings the ultimate boot up experience. The lightning boot up speed makes it hard to access the UEFI setup. ASRock Restart to UEFI allows users to enter the UEFI automatically when turning on the PC. By enabling this function, the PC will enter the UEFI directly after you restart.
-
Page 16: Asrock Home Cloud
ASRock FAN-Tastic Tuning ASRock FAN-Tastic Tuning is included in A-Tuning. Configure up to five different fan speeds using the graph. The fans will automatically shift to the next speed level when the assigned temperature is met. -
Page 17: Chapter 2 Installation
Chapter 2 Installation This is a Micro ATX form factor motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Pre-installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings. -
Page 18: Installing The Cpu
H87M Pro4/ASM 2.1 Installing the CPU 1. Before you insert the 1150-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. - Page 20 H87M Pro4/ASM Please save and replace the cover if the processor is removed. The cover must be placed if you wish to return the motherboard for after service.
-
Page 21: Installing The Cpu Fan And Heatsink
2.2 Installing the CPU Fan and Heatsink... -
Page 22: Installing Memory Modules (Dimm)
H87M Pro4/ASM 2.3 Installing Memory Modules (DIMM) This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. 1. For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDR3 DIMM pairs. -
Page 24: Expansion Slots (Pci And Pci Express Slots)
H87M Pro4/ASM 2.4 Expansion Slots (PCI and PCI Express Slots) There are 2 PCI slots and 2 PCI Express slots on the motherboard. Before installing an expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. -
Page 25: Jumpers Setup
2.5 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins. -
Page 26: Onboard Headers And Connectors
H87M Pro4/ASM 2.6 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard. System Panel Header... - Page 27 Serial ATA3 Connectors These six SATA3 (SATA_0_1: connectors support SATA see p.1, No. 11) data cables for internal (SATA_2_3: storage devices with up to see p.1, No. 10) 6.0 Gb/s data transfer rate. (SATA_4_5: see p.1, No. 9) USB 2.0 Headers Besides two USB 2.0 ports USB_PWR (9-pin USB6_7)
- Page 28 H87M Pro4/ASM 1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system. 2. If you use an AC’97 audio panel, please install it to the front panel audio header by the steps below: A.
- Page 29 CPU Fan Connectors This motherboard pro- +12V CPU_FAN_SPEED (4-pin CPU_FAN1) vides a 4-Pin CPU fan FAN_SPEED_CONTROL (see p.1, No. 3) (Quiet Fan) connector. If you plan to connect a (3-pin CPU_FAN2) 3-Pin CPU fan, please (see p.1, No. 2) connect it to Pin 1-3. +12V FAN_SPEED ATX Power Connector...
- Page 30 H87M Pro4/ASM Chassis Intrusion Header This motherboard (2-pin CI1) supports CASE OPEN Signal (see p.1, No. 19) detection feature that detects if the chassis cove has been removed. This feature requires a chassis with chassis intrusion detection design. TPM Header...
-
Page 31: Contenido Del Paquete
Si esta documentación sufre alguna modificación, la versión actualizada estará disponible en el sitio web de ASRock sin previo aviso. Si necesita asistencia técnica relacionada con esta placa base, visite nuestro sitio web para obtener información específica sobre el modelo que esté... -
Page 32: Especificaciones
H87M Pro4/ASM 1.2 Especificaciones Plataforma • Factor de forma Micro ATX • Diseño de los Condensadores: All Solid • Compatible con 4.ª Generación de Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® en paquete LGA1150 • Diseño Digi Power... - Page 33 • Compatible con monitores triples • Compatible con Tecnología HDMI con máxima resolución hasta 1920x1200 @ 60Hz • Compatible con DVI-D con máxima resolución hasta 1920x1200 @ 60Hz • Compatible con D-Sub con máxima resolución hasta 1920x1200 @ 60Hz • Compatible con Auto Lip Sync, Deep Color (12bpc), xvYCC y HBR (audio de alta velocidad de bits) con HDMI (requiere un monitor compatible con HDMI) • Compatible con función HDCP con puertos DVI-D y HDMI...
- Page 34 H87M Pro4/ASM Almace- • Los 6 conectores SATA3 de 6,0 Gb/s, compatibles con RAID namiento (RAID 0, RAID 1, RAID 5, RAID 10, Tecnología Rapid Storage 12 de Intel y Tecnología Smart Response de Intel), NCQ, AHCI y “Hot Plug”...
- Page 35 Windows® de 32 bits. Los sitemas operativos Windows® de 64 bits no tienen estas limitaciones. Podrá utilizar XFast RAM de ASRock para usar la memoria que Windows® no puede utilizar.
- Page 36 H87M Pro4/ASM 1.3 Instalación de los puentes La instalación muestra cómo deben instalarse los puentes. Cuando la tapa de puente se coloca en los pines, el puente queda “Corto”. Si no coloca la tapa de puente en los pines, el puente queda “Abierto”. La ilustración muestra un puente de 3 pines cuyo pin 1 y pin 2 son “Cortos”...
- Page 37 1.4 Conectores y cabezales incorporados Los cabezales y conectores incorporados NO son puentes. NO coloque tapas de puente sobre estos cabezales y conectores. Si coloca tapas de puente sobre los cabezales y conectores dañará de forma permanente la placa base. Cabezal del panel del Conecte el interruptor de alimentación,...
- Page 38 H87M Pro4/ASM Conectores Serie ATA3 Estos seis conectores (SATA_0_1: SATA3 son compatibles consulte la pág.1, N.º 11) con cables de datos SATA (SATA_2_3: para dispositivos de consulte la pág.1, N.º 10) almacenamiento interno (SATA_4_5: con una velocidad de consulte la pág.1, N.º 9) transferencia de datos de hasta 6,0 Gb/s.
- Page 39 1. El Audio de Alta Definición (HDA, en inglés) es compatible con el método de sensor de conectores, sin embargo, el cable del panel del chasis deberá ser compatible con HDA para que pueda funcionar correctamente. Siga las instrucciones que se indican en nuestro manual y en el manual del chasis para instalar su sistema.
- Page 40 H87M Pro4/ASM Conectores del ventilador Esta placa base contiene de la CPU un conector de ventilador (CPU_FAN1 de 4 pines) (ventilador silencioso) de (consulte la pág.1, N.º 3) CPU de 4 pines. Si tiene pensando conectar un (CPU_FAN2 de 3 pines) ventilador de CPU de 3 (consulte la pág.1, N.º...
- Page 41 Cabezal de intrusión de Esta placa base es chasis compatible con la (CI1 de 2 pines) función de detección de (consulte la pág.1, N.º 19) CUBIERTA ABIERTA que detecta si se ha retirado la cubierta del chasis. Esta función requiere un chasis diseñado para la detección de intrusión del chasis.
-
Page 42: Conteúdo Da Embalagem
Web site para obter informações específicas acerca do modelo que está a utilizar. Também poderá encontrar a lista de placas VGA e CPU mais recentes suportadas no Web site da ASRock. Web site da ASRock http://www.asrock.com. - Page 43 1.2 Especificações • Formato Micro ATX Plataforma • Design de condensador sólido • Suporta processadores Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® de 4ª geração em socket LGA1150 • Design Digi Power • Design com 4 fases de alimentação • Suporta a tecnologia Intel®...
- Page 44 H87M Pro4/ASM • Suporta configuração com três monitores • Suporta tecnologia HDMI com resolução máxima de até 1920x1200 @ 60Hz • Suporta DVI-D com resolução máxima de até 1920x1200 @ 60Hz • Suporta D-Sub com resolução máxima de até 1920x1200 @ 60Hz • Suporta Auto sincronização labial, Deep Color (12bpc),...
- Page 45 Armazena- • 6 x conectores SATA3 a 6,0 Gb/s, com suporte para RAID mento (RAID 0, RAID 1, RAID 5, RAID 10, tecnologia Intel Rapid Storage 12 e tecnologia Intel Smart Response), NCQ, AHCI e “Hot Plug” Conector • 1 x Terminal IV • 1 x Terminal de porta de impressão • 1 x Terminal de porta COM • 1 x Terminal de intrusão no chassis...
- Page 46 Devido às limitações, o tamanho real da memória de 4GB reservada para utilização em sistemas operativos Windows® 32-bits poderá ser inferior. Os sistemas operativos Windows® 64-bits não possuem essas limitações. Pode utilizar o ASRock XFast RAM para dar uso à memória que o Windows® não utiliza.
- Page 47 1.3 Configuração dos jumpers A imagem abaixo ilustra como os jumpers são configurados. Quando a tampa do jumper é colocada nos pinos, o jumper é "Curto". Se não for colocada uma tampa de jumper nos pinos, o jumper é "Aberto". A imagem ilustra um jumper de 3 pinos cujos pino1 e pino2 estão "Curtos"...
- Page 48 H87M Pro4/ASM 1.4 Terminais e conectores integrados Os terminais e conectores integrados NÃO são jumpers. NÃO coloque tampas de jumpers sobre estes terminais e conectores. Colocar tampas de jumpers sobre os terminais e conectores irá causar danos permanentes à placa principal.
- Page 49 Conectores ATA3 de série Estes seis conectores (SATA_0_1: SATA3 suportam consultar p.1, N.º 11) cabos de dados SATA (SATA_2_3: para dispositivos de consultar p.1, N.º 10) armazenamento interno (SATA_4_5: com uma velocidade de consultar p.1, N.º 9) transferência de dados de até...
- Page 50 H87M Pro4/ASM 1. O Áudio de alta definição suporta Detecção de ficha, mas o cabo de painel no chassis deverá suportar HDA para funcionar correctamente. Siga as instruções no nosso manual e no manual do chassis para instalar o seu sistema.
- Page 51 Conectores da ventoinha Esta placa principal inclui da CPU um conector de ventoinha (CPU_FAN1 de 4 pinos) de CPU (Ventoinha (consultar p.1, N.º 3) silenciosa) de 4 pinos. Se pretender ligar uma (CPU_FAN2 de 3 pinos) ventoinha de CPU de 3 (consultar p.1, N.º...
- Page 52 H87M Pro4/ASM Terminal de intrusão do Esta placa principal chassis suporta a função de (CI1 de 2 pinos) detecção de ABERTURA (consultar p.1, N.º 19) da CAIXA que detecta se a tampa do chassis foi removida. Esta função requer um chassis com design de detecção de...
-
Page 53: Contact Information
Contact Information If you need to contact ASRock or want to know more about ASRock, you’re welcome to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer for further information. For technical questions, please submit a support request form at http://www.asrock.com/support/tsd.asp...