Table of Contents
Advertisement
To link the Hue bridge...
1 - With the TV connected to the network, it will show the
available Hue bridges. If the TV did not find your hue bridge yet,
you can select Scan again and press OK.
If the TV found the only hue bridge you have, select Next and
press OK.
If you have more than one hue bridge available, press (up) or
(down) to select the hue bridge you want to use and then
select Next and press OK.
2 - After you pressed OK, go to the Philips hue bridge and
press the link button in the middle of the device. This will link
the hue bridge with the TV. Do this within 30 seconds. The TV
will confirm if a hue bridge is linked to the TV.
3 - On this confirmation, select OK and press OK.
With the Philips hue bridge linked to the TV, go to page Hue
bulbs.
Hue bulbs
In the following step, you will select the Philips hue bulbs that
have to follow the Ambilight.
You can select a maximum of 9 Philips hue bulbs for
Ambilight+hue.
To select the bulbs for Ambilight+hue...
1 - In the Configure Ambilight+hue menu, select Hue bulbs and
press OK.
2 - Mark the bulbs that have to follow the Ambilight. To mark a
bulb, select the bulb name and press OK.
3 - When you're done, select the OK button and press OK.
With the bulbs marked for Ambilight+hue, go to page
Configure bulb.
Configure bulb
In the following step, you will configure each Philips hue bulb.
To configure each hue bulb...
1 - Select the bulb name in the Configure Ambilight+hue menu
and press OK. The bulb you selected is blinking.
2 - First indicate where you placed the bulb relative to the TV. A
correct setting of the Angle will send the correct Ambilight
colour to the bulb. Press (up) or (down) to adjust.
3 - Press (right) to set the distance.
4 - Secondly, indicate the Distance between the bulb and the
TV. The further away from the TV, the weaker the Ambilight
colour. Press (up) or (down) to adjust.
5 - Press (right) to set the brightness.
6 - Finally, set the Brightness of the bulb. Press (up) or
(down) to adjust.
7 - To stop configuring this bulb, select OK and press OK.
8 - In the Configure Ambilight+hue menu, you can select every
bulb and do the same.
9 - When all Ambilight+hue bulbs are configured, select Finish
and press OK.
Ambilight+hue is ready for use.
You can always change the Ambilight+hue configuration later.
To change the configuration, press and select Setup > TV
settings > Ambilight > Ambilight+hue.
Immersion
With Immersion, you can adjust the level of the Ambilight effect
for the Ambilight+hue bulbs.
To adjust the Ambilight+hue Immersion...
1 - Press and select Setup and press OK.
2 - Select TV settings > Ambilight > Ambilight+hue >
Immersion and press OK.
3 - Press (up) or (down) to adjust.
4 - Press , repeatedly if necessary, to close the menu.
Info
In View configuration, you can consult the current
Ambilight+hue configuration. Which network you use, how
many bulbs are connected, etc.
To view the current Ambilight+hue setup...
1 - Press and select Setup and press OK.
2 - Select TV settings > Ambilight > Ambilight+hue > View
configuration and press OK.
3 - Select the item you want to view and press OK.
4 - Press , repeatedly if necessary, to close the menu.
Advanced Ambilight settings
Wall colour
With Wall colour, you can neutralise the influence of a coloured
wall on the Ambilight colours. Select the colour of the wall
behind the TV and the TV will modify the Ambilight colours to
appear as they are intended.
To select the colour of the wall . . .
1 - Press and select Setup and press OK.
2 - Select TV settings > Ambilight > Advanced > Wall colour.
3 - Select the colour sample that matches the colour of the wall
behind the TV and press OK.
4 - Press , repeatedly if necessary, to close the menu.
TV switch off
With TV switch off, you can set Ambilight to switch off
immediately or slowly fade out when you switch off the TV. The
slow fade out gives you some time to switch on the lights in
your living room.
65
Advertisement
Table of Contents
