Download Print this page
Dimplex XMS718N Installation And Operating Instructions
Dimplex XMS718N Installation And Operating Instructions

Dimplex XMS718N Installation And Operating Instructions

Combined storage and convector heater

Advertisement

Quick Links

XMC(N)
MODELS:
XMC712N
XMC718N
XMC724N
INSTALLATION
PLEASE READ THIS LEAFLET CAREFULLY AND RETAIN FOR FURTHER USE.
NOTE ALSO THE INFORMATION GIVEN ON THE HEATER
The installation must be carried out by a trained competent personnel.
A means for disconnection must be incorporated in the fi xed wiring by a double pole switch with a contact separation
of a minimum of 3mm and in accordance with the current IEE Wiring Regulations
The heater must not be installed immediately below a fi xed socket outlet.
The heater is not suitable for connection to a 30A ring circuit (24 hour peak supply).
Do not position the heater under windows where curtains can contact the heater casing.
WARNING - THE SURFACES ON THIS HEATER CAN BE HOT
This heater meets EN60335 safety requirements. However, any heater type becomes hot in normal operation. Care
must be taken to ensure that prolonged skin contact with the heater does not occur.
WHERE YOUNG CHILDREN, INFIRM PERSONS, OR THE AGED ARE PRESENT THIS APPLIANCE MUST BE
ADEQUATELY GUARDED. Contact your installer or manufacturer for further advice.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision for instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
This appliance is very heavy and must be securely fi xed to a wall. DO NOT UNDER ANY CIRCUMSTANCES
ATTEMPT TO MOVE OR REPOSITION THIS HEATER WITHOUT SEEKING EXPERT ADVICE.
To maintain stability, it is essential that the heater is placed on a level surface.
This heater must be installed where it is impossible for switches and other controls to be touched by a person using
a bath or shower.
IMPORTANT - Due to the newness of materials the heater will produce a slight smell for the fi rst few days of
operation. ROOMS MUST BE WELL VENTILATED AND YOUNG CHILDREN, CAGED BIRDS, OR PERSONS
WITH RESPIRATORY COMPLAINTS MUST NOT REMAIN IN CLOSE PROXIMITY TO THE HEATER DURING
THE FIRST 48 HOURS OF THE COMMISSIONING PERIOD.
IF, DURING ANY REASSEMBLY OF THE HEATER, A PART OF THE THERMAL INSULATION SHOWS DAMAGE
OR DETERIORATION WHICH MAY IMPAIR SAFETY, IT SHOULD BE REPLACED BY AN IDENTICAL PART.
COMBINED STORAGE AND
CONVECTOR HEATER
1.7kW/12kWh
2.55kW/18kWh
3.4kW/24kWh
INSTRUCTIONS
IMPORTANT
Storage and 1kW Convector
Storage and 1.5kW Convector
Storage and 2kW Convector
OPERATING
AND

Advertisement

loading

Summary of Contents for Dimplex XMS718N

  • Page 1 XMC(N) COMBINED STORAGE AND CONVECTOR HEATER MODELS: XMC712N 1.7kW/12kWh Storage and 1kW Convector XMC718N 2.55kW/18kWh Storage and 1.5kW Convector XMC724N 3.4kW/24kWh Storage and 2kW Convector INSTALLATION OPERATING INSTRUCTIONS IMPORTANT PLEASE READ THIS LEAFLET CAREFULLY AND RETAIN FOR FURTHER USE. NOTE ALSO THE INFORMATION GIVEN ON THE HEATER The installation must be carried out by a trained competent personnel.
  • Page 2 INSTALLATION INSTRUCTIONS Place the heater on its feet and in the desired position PREPARATION against the wall. Ensure the heater is based on a fi rm level surface at least 75mm from any end wall and at least 250mm below any shelf or similar projection. Cut away any The heater will arrive Model 712N - 8 bricks gripper rod or carpet which would prevent the heater sitting...
  • Page 3 Fit the front layer of bricks again with the recess towards the element. The complete core will comprise: 712N - 2 x 4 Brick Columns 718N - 3 x 4 Brick Columns 724N - 4 x 4 Brick Columns Replace the inner front complete with insulation by locating its bottom edge behind the front lip of the chassis and inserting retaining screws along the top and both sides.
  • Page 4 Should you require after sales information please go to Initially set the input to 4. If the heater does not maintain a satisfactory room www.dimplex.co.uk where you will fi nd our self help guide temperature the following day this setting should be increased. Conversely by clicking on ‘After Sales’...

This manual is also suitable for:

Xms724nXms712n