Related Manuals for Igloo ARBF Series
Summary of Contents for Igloo ARBF Series
- Page 1 Instruction Manual Ice Cream/ Gelato Cases Models: ARBF & ARB2F series ARB2TF ARB2F ARBTF ARBF 124 Norfinch Dr. Toronto, ON. M3N 1X1 Tel : 416-663-3051 Fax : 416-663-5793 REFRIGERATION LTD. Toll Free : 1-888-408-8819...
-
Page 2: Table Of Contents
REFRIGERATION LTD Contents 1 UNLOADING ..............................3 2 PROPERTIES OF THE UNIT..........................3 2.1. Purpose ..............................3 2.2. Description of the unit..........................3 2.3. Technical data ............................5 3. PREPARING THE DEVICE FOR START UP ......................6 3.1. Installation requirements .......................... 6 3.2. -
Page 3: Unloading
REFRIGERATION LTD 1 UNLOADING The unit should be transported in vertical position and properly secured and packed. 2 PROPERTIES OF THE UNIT 2.1. Purpose “ARBF” and “ARB2F” are universal freezing devices aimed for displaying and short-lasting storage of scooped ice cream in temperature ranging between -24ºC and -15ºC with ambient temperature of +15ºC/+25ºC and relative air humidity up to 55%, depending on the environment of the unit location. -
Page 4: Figure 1 Arbf & Arb2F - Overview
REFRIGERATION LTD Figure 1 ARBF & ARB2F - Overview 1 – LED lamp 7 – Side glass 2 – Telescopic front glass lifting system 8 – Serial plate 3 – Wooden casing 9 – Control panel 4 – Leveling legs 10 –... -
Page 5: Technical Data
Never plug in more than one unit per electric circuit If in doubt, call an electrician. IGLOO will not warranty any equipment that is connected to an extension cord or adapter plug. The equipment may be turned on after confirmation of the fire protection efficiency with results of measures performed according to binding regulations! Ice Cream/ Gelato Cases| www.igloorefrigeration.com... -
Page 6: Unit Location
REFRIGERATION LTD ■ NEMA Plugs IGLOO refrigeration uses this type of plug. If you 115/60/1 do not have the right outlet, have a certified NEMA-5-20R electrician install the correct power source. 3.2. Unit Location Remove cardboard angles and protective foil. -
Page 7: Figure 5 Install Internal Elements
REFRIGERATION LTD After installation of the equipment at the destination location it should be left to rest for at least 2 hours before turning it on (for devices with built-in compressor) to set the level of refrigerant in order to prevent problems with the start up. WARNING: Keep the cooling circuit away from damage! ... -
Page 8: Unit Start Up
REFRIGERATION LTD 4. UNIT START UP Temperature of the cooled space and aggregate operating cycle may fluctuate. This depends on numerous factors, such as amount and temperature of products placed in the device and temperature of the surroundings. The equipment should be placed in a dry and well-ventilated place, ensuring proper air exchange (distance between the wall and the equipment–... -
Page 9: Temperature Regulation
REFRIGERATION LTD 4.1. Temperature regulation The thermostat is to obtain the set temperature within the equipment and maintain it within the determined temperature ranges. The manufacturer enters all settings of temperature regulators required for normal functioning of the equipment. Before primary actuation the user should control and possibly set the required temperature inside the equipment on the control panel. - Page 10 REFRIGERATION LTD Diode 8 – Defrost: Pressing this button alone: more than 3 sec. activates/deactivates the defrost. Pressing with other buttons: pressed together with 6 activates/deactivates the continuous cycle, Start Up: hold for 1 sec. displays firmware version. SETTING THE DESIRED TEMPERATURE - Press the set button for 1 second leading value shall be displayed on the screen - Increase or decrease the leading value by means of...
- Page 11 REFRIGERATION LTD - Use the UP and DOWN buttons to scroll the parameters. The LED corresponding to the category of parameters will be on; - Press SET to display the value associated with the parameter - Increase or decrease the value using the UP or DOWN button respectively; - Press SET to temporarily save the new value and display the parameter again;...
-
Page 12: Maintenance
REFRIGERATION LTD digital input alarm delay enable alarm “Ed” (end defrost by timeout) set point dirty condenser alarm °C dirty condenser alarm differential temperature °C dirty condenser alarm delay enable evaporator fan control evaporator fan control set point -2.0 °C stop evaporator fan if compressor off evaporator fan status during defrost post-dripping time... -
Page 13: Service
REFRIGERATION LTD Figure 9 Cleaning the condenser It is essential to keep the condenser clean. Dirt may hinder the heat exchange, causing increase in electricity consumption and may cause damage to the compressor. In order to clean the condenser it is necessary to unscrew the sheet metal screws and pull the wind brace out of catch by lifting it up. -
Page 14: Service
IGLOO Refrigeration service Telephone number: 416-663-3051 or (toll free) 1-888-408-8819 E-mail: service@igloo400.com If after checking points described in chapter 6.1 “Faults identification and repair” the unit still does not work properly, Please contact Technical Service @ IGLOO Refrigeration. www.igloorefrigeration.com Ice Cream/ Gelato...