Advertisement
DIGITAL TUNER
DIGITAL TUNER
Tuning to radio stations
1. Adjust the POWER slider to AM or FM.
™ The radio station frequency, waveband are
shown (See 3)
2. Press and hold SEARCH ∞ or § until the
frequency in the display starts running.
™ The radio automatically tunes to a station of
sufficient reception. Display shows Srch
during automatic tuning.
3. Repeat step 2 if necessary until you find the
desired station.
• To tune to a weak station, press ∞ or § briefly
and repeatedly until you have found optimal
reception.
To improve radio reception:
• For FM, extend, incline and turn the telescopic
antenna. Reduce its length if the signal is too
strong.
• For AM , the set uses a built-in antenna. Direct this
antenna by turning the whole set.
Programming radio stations
You can store up to a total of 30 radio stations (20 FM
and 10 AM) in the memory, manually or automatically
(Autostore).
DIGITAL TUNER
Manual programming
1. Tune to your desired station (see Tuning to radio
stations).
2. Press PROG to activate programming.
™ PROG flashes.
-
+
3. Press PRESET
/
once or more to select a
preset number.
• Remote control (AZ1325 models only): Press
-
+
PRESET
/
once or more to select a preset
station.
4. Press PROG to confirm.
5. Repeat steps 1-4 to store other stations.
Note : You can erase a preset station by storing
another frequency in its place.
Autostore
Autostore automatically starts programming radio
stations from preset 1. Available stations are
programmed in order if the station with sufficient
reception strength. Any previous presets e.g. manually
programmed will be erased.
• Press PROG for 2 seconds or more to activate
autostore programming.
™ The display shows AUtO, PROG blinks,
followed by the radio station details when
stored.
After all stations are stored, the first preset station
will then automatically play.
To listen to a preset station
-
+
• Press the PRESET
,
buttons once or more until
the desired preset station is displayed.
+
• Remote control : optionally, press PRESET
select your preset station.
CD PLAYER
Playing a CD
This CD-player can play all kinds of Audio Discs such
as CD-Recordables and CD-Rewritables. Do not try to
play a CD-ROM, CDi, VCD, DVD or computer CD.
1. Adjust the POWER slider to CD.
2. Open the CD Door.
™ OPEN is displayed.
3. Insert a CD with the printed side facing up and
close the door.
™ no cd if no CD inserted/ CD dirty, incorrectly
inserted or damaged.
™ nF cd if you have inserted a non-finalized CD-
R(W).
4. Press 2; to start playback.
5. To pause playback press 2;. Press 2; again to
resume play.
™ Display: flashes during pause.
6. To stop CD playback, press the 9 button.
Note : CD play will also stop when:
- the CD door is opened
- the CD has reached the end
- you select AM / FM function.
Selecting a different track
• Press SEARCH ∞ or § once or repeatedly to
select your track.
• In the pause / stop position, press 2; to start
playback.
-
,
to
CD PLAYER
Finding a passage within a track
1. Press and hold SEARCH ∞ or §.
– The CD is played at high speed and low volume.
2. When you recognize the passage you want,
release ∞ or § to resume normal playback.
Note : During a CD program or if SHUFFLE/
REPEAT active, searching is only possible within a
track.
Different play modes: SHUFFLE and REPEAT
You can select and change the various play modes
before or during playback, and combine the modes
with PROG. (See 4)
(SHUFFLE) - tracks of the entire CD/ program
are played in random order
(SHUFFLE REPEAT ALL) - to repeat the
entire CD/ program continuously in random order
(REPEAT ALL) - repeats the entire CD/
program
(REPEAT) - plays the current track continuously
1. To select play mode, press MODE once or more.
2. Press 2; to start playback if in the stop position.
3. To select normal playback, press MODE
repeatedly until the various modes are no longer
displayed.
– You can also press the 9 button to cancel your
play mode.
Advertisement
