Table of Contents
Advertisement
Safety, performance, and dependability have been given
top priority in the design of your 1/3 sheet sander.
INTENDED USE
The 1/3 sheet sander is intended for sanding and fi nishing
metal, wood, plastic or similar materials using the abrasive
pads or sheets provided. The 1/3 sheet sander is intended
to be used by adult operators who have read the instruction
manual and understand the risks and hazards. The 1/3
sheet sander should only be used in well ventilated areas.
The 1/3 sheet sander is designed for dry sanding only.
The 1/3 sheet sander is intended only for consumer use.
Do not use the product in any way other than those stated
in intended use. Use of the product for operations different
from intended could result in a hazardous situation.
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SHEET SANDER SAFETY WARNINGS
■
Always wear safety goggles and a dust mask.
■
A suitable breathing respirator must be worn while
sanding lead paint, some woods and metal to avoid
breathing the harmful/toxic dust or air. Contact with
or inhalation of dust produced from these materials can
endanger the health of operator and bystanders.
■
Do not throw sanding dust on an open fire because
materials in fine particle form may be explosive.
■
The product is not suitable for wet sanding.
■
When not in use, all tools should be disconnected from
power source.
■
Caution, fire hazard! Avoid overheating the object being
sanded as well as the sander. Always empty the dust
collector before taking breaks.
■
Clamp
workpiece
with
Unclamped workpieces can cause severe injury and
damage. Do not hold the material you are sanding by
hand.
■
Do not apply excessive pressure to the product.
■
Do not use sanding paper larger than needed. Extra
paper extending beyond the sanding pad can also
cause serious lacerations.
■
The dust collection box shall be equipped with the
tool. It should be emptied frequently. To connect dust
collection box, insert the adapter of dust box to the dust-
collection opening on the rear end of the sander.
WARNING
Do not throw sanding dust into an open fire because
materials in fine particle form may be explosive.
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■
■
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fi ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
a
clamping
device.
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■
■
■
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARNING
A suitable breathing respirator must be worn while
sanding lead paint, some woods and metal to avoid
breathing the harmful/toxic dust or air.
WARNING
Dust from certain paints, coatings, and materials may
cause irritation or allergic reactions. Dust from wood,
such as oak, beech, MDF, and others are carcinogenic.
Materials containing asbestos should only be worked on
or processed by qualifi ed specialist operators.
RESIDUAL RISKS
Injury caused by dust
–
Using the product will produce considerable amount
of dust and fine particles. Use the dust collection
device or connect a dust extraction vacuum when
operating the product. Wear dust masks containing
filters appropriate to the materials being worked on.
Ensure adequate workplace ventilation. Do not eat,
drink, or smoke in the work area.
Injury caused by noise and vibration
–
Wear ear protection during the sanding operation.
Do not operate the product for long periods of time.
See "Risk reduction".
RISK REDUCTION
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
After each period of operation, exercise to increase
blood circulation.
Take frequent work breaks. Limit the amount of
exposure per day.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English |
1
Advertisement
Table of Contents
