LCD PROJECTION TELEVISION Chassis : M51A Model: SP403JHPX/UMG COLOR TELEVISION RECEIVER CONTENTS Precautions Reference Information Specifications Disassembly and Reassembly Alignment and Adjustments Troubleshooting Exploded View and Parts List Electric Parts List Block Diagram PCB Layout Diagram Wiring Diagram Schematic Diagrams...
The current measured should the XÐray Protection Specifications Label, and not exceed 0.5 milliamp. Reverse the power- the Product Safety and X-ray Warning Note on plug prongs in the AC outlet and repeat the the service data schematic. test. Samsung Electronics...
Page 3
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheat- ing, and correct any potential hazards. Samsung Electronics...
Page 4
(except lamp) are damaged, replace the whole optical engine. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). Samsung Electronics...
Page 5
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such can generate electrical charges that damage as brushing clothes together, or lifting a foot ESDs. from a carpeted floor can generate enough static electricity to damage an ESD. Samsung Electronics...
Millimeter Hour Millisecond Inches Per Second Millivolt Kilowatt-hour Nanofarad Ω Kilogram Kilohertz Picofarad kΩ Kilohm Pound Kilometer Revolutions Per Minute km/h Kilometer Per Hour Revolutions Per Second Kilovolt Second (Time) Kilovolt-ampere Volt Kilowatt Volt-ampere Liter Watt Megahertz Watt-hour Samsung Electronics...
Page 7
Fail Safe Voltage Controlled Oscillator Ground VCXO Voltage Controlled Crystal Oscillator Green-Y Very High Frequency High Video Intermediate Frequency High-Frequency Variable Resistor HI-FI High Fidelity Video Tape Recorder Inductance-Capacitance VTVM Vacuum Tube Voltmeter Integrated Circuit Transistor Intermediate Frequency Samsung Electronics...
Page 8
SONY RGB DRIVER CXA2504N SONY SAMPLE/HOLD DRIVER CXD2443Q SONY TIMING GENERATOR CIP3250A COMPONENT INTERFACE PROCESSOR VPC3215C VIDEO PROCESSOR TL7705AC POWER-ON RESET GENERATOR FEATURE-BOX SDA9280 SIEMENS DISPLAY PROCESSOR SDA9272 SIEMENS VIDEO INTERPOLATION PROCESSOR SDA9253 SIEMENS DRAM 74F125 PHILIPS BUFFER Samsung Electronics...
Page 9
Reference Information Table 2 - 2 IC Line - Up SPECIFICATION BLOCK MAKER FUNCTION TDA9815 PHILIPS DEMODULATOR TDA9160 PHILIPS DECORDER/SYNC PROCESSOR SDA9187-2X SIMENS A/D CONVERTER FOR PIP SDA9189X SIMENS PIP PROCESSOR Samsung Electronics...
2. Loosen the 4 screws and remove 3. After loosening the 4 screws, remove the lens the supporter. cover and fan duct. 4. Loosen the 2 screws. Remove the optical 5. Loosen the 2 screws. Remove the stabilizer. meter. Samsung Electronics...
Page 13
Disassembly and Reassembly 6. After loosening the 2 screws, remove the 7. After removing the 6 screws, pull the top chassis holder and power mounting. cabinet backwards. Samsung Electronics...
Page 14
(Ò00000Ó). ÒDisplay P.STD Mute PowerÓ (3) Press the Power key to reset the factory value. (4) Press the DISPLAY key to verify that the ø lamp use time is 00 Lamp Total time (05999) 01 Lamp Life (05999) Samsung Electronics...
Page 15
4-2-1 Lamp (Bulb only) Replacement 1. Loosen the two screws. 2. Remove the lamp-bracket from the lamp assembly. 3. After loosening the two brackets, remove the 4. After loosening one screw and one nut, lamp-holder and wires. remove the bulb. Samsung Electronics...
Page 16
Disassembly and Reassembly 4-3 Air Filter Check 1. Loosen the screw. 2. Remove the cover. 3. After removing the holder and filter from the cover, clean the filter. FILTER Samsung Electronics...
Page 17
2. Loosen the 3 screws. Remove the supporter. backwards. 3. After loosening the 4 screws, remove the lens 4. Loosen the 2 screws. Remove the optical cover and fan duct. meter. 5. Remove the GUIDE from the FPC-Connector. 6. Remove FPC cable from the FPC-Connector. Samsung Electronics...
Page 18
Disassembly and Reassembly 7. Loosen the 2 screws, 2 PCB spacers and 8. Using a hexagonal wrench, loosen the two remove the PCB-LCD. screws. 9. Lift the LCD in the direction of arrow. Samsung Electronics...
Page 19
Disassembly and Reassembly 4-5 Speaker Removal 1. Loosen the 4 screws and remove the speaker holders. Samsung Electronics...
5. Reposition the optical assembly, and fasten all 4 screws. 6. Check the focus adjustment. 7. Repeat adjustments 1~5, if necessary. FOCUS SECURING SCREW Fig. 5-1 Samsung Electronics...
Page 21
3. When moving the liquid crystal panel towards the left, the screen moves right (and vice versa). 5. Repeat adjustments 2~4 until the screen center is aligned vertically and horizontally. 6. Using a hexagonal wrench, refasten the two screws. HEXAGONAL SCREW (FOR SECURING LIQUID CRYSTAL PANEL) Fig. 5-2 Samsung Electronics...
Page 22
REAR MENU EXT 1 (A/V IN) (RGB IN) VOLUME Volume Button 1. Press for the volume UP/DOWN. 2. Press for content adjustment. HEADPHONE Sound Input Terminal (Right) Sound Input Terminal (left) Video Input Terminal VIDEO Seperate-Video Input Terminal Samsung Electronics...
Page 23
Adjusts the color difference signal level of YUVIN 1 PEAK DRIVE LIMIT Adjustment for the peak drive limit P.YC DELAY Adjustment for the P.YC delay Adjusts the center of tint (0 ®R 9 ®CENTER 17 ®G ) SUB TINT g CORRECTION Adjustment for the g correction Samsung Electronics...
Page 24
The greater the value, the darker it gets. Adjusts the limiter voltage of white peak of R,G,B video signal (applied White limit to LCD). The greater the value, the lower the limiter voltage becomes. Samsung Electronics...
Page 25
Range Initial value Description LCD h pos Determines the start location of horizontal indication by picture element. LCD v pos Determines the start location of vertical indication (within 1H) SH position Determines the phase of the sample/hold pulse. Samsung Electronics...
Page 26
Center speaker S-audio mute on/off Scart audio mute Blue screen on/off Blue screen UHF only on/off UHF only on/off Vga input Atm one run on/off Atm one run Size key on/off Size key vert. peaking on/off vert. peaking Samsung Electronics...
Page 27
Ref. 3. Adjust the red drive so that the signal ampli- tude becomes 0.7Vp-p. 4. Adjust the Sub-brightness of TDA4780 so that the waveform (without sync) is seen as shown in the figure below. REF Pulse Sync Samsung Electronics...
Page 28
(1 V/div, 10 u sec/div) gamma ctrl1, crtl2 for the waveform shown below. 3. Reverse the CH2 signal, and add CH1 and CH2 in ADD mode. 4. Adjust R sub-contrast and R sub-brightness waveforms, as shown below: Contrast Adjustment Brightness Adjustment Samsung Electronics...
Page 29
2. Adjust the LCD Horizontal/Vertical POS. 3. Set the signal center to 7V. 5-6-13 Common Voltage Adjustment 1. Connect LCD COMMON input to an oscilloscope, and check the waveform. (1 V/div, 10 u sec/div) Set the common control to 6.8V. 5-10 Samsung Electronics...
Page 30
2. The picture is turned to blue screen and “TEMPERATURE” character blinks for about 5 ~ 6 seconds. 3. The power is turned off and “TEMP” LED is blinking for about 20 seconds. (This is not a TV set failure and normal operation) Samsung Electronics 5-11...
3. Use the Vol (+) key and Vol ( - ) key to change data. (1) Press the Vol (+) key to increase data. (2) Press the Vol (-) key to decrease data. 4. Use the Power key to exit and store data in memory. Samsung Electronics...
Page 32
Main Board Check Check LED Operation SDA1/SCL1 See "5-7 LED Display on the Micom Check" Module See "6-5 No Standy" Check/Replace Tuner MICOM Module AUDIO Module A/V Terminal Board (TDA6920) Progressive Module LCD Control Board (TDA4780) Samsung Electronics...
Page 33
Check the circuitry near ICL404 and replace Check ICL404(TDA4780) micom module #20(B-OUT),#22(G-OUT) #24(R-OUT) Check the circuitry near ICL404, replace IC201 (TDA4780) Check ICL204(CXA1853Q) #9(R-in),#10(G-in),#11(B-in) Check the circuitry near QL401,QL402,QL403 around of ICL404(TDA4780) Check ICL205(CXA2504N) #23,#25,#27,#33,#35,#37 Check/ Replace Replace ICL205(CXA2504N) CNL04 (24P) Samsung Electronics...
Page 34
IC808 IC808 Regulator pin 5 (over 6V) IC (SI-3050C) Check the AC Check the associated power supply of D826 circuitry parts of T802, IC801 Replace F801 Check F801 (AC250V/6.3A) Check L801,L802, C801, C802, V801, R801 Samsung Electronics...
Page 35
DC voltage of BALLAST Main Board (over 3.5V) (about 300V) Check F801 (on the Check the voltage Check AB1 on the Power Board), D803, and of IC904(SAA1300) pin 6 Ballast Board surrounding circuitry (over 3.5V)on the Main Board Samsung Electronics...
Page 36
2H-sync to ICL301(CXD2443Q) Pin 13 on (74HC123) Pin13,FI302 the LCD Control Board Check voltage of TL301 Check the voltage of CNL06 so that the voltage of RPD (2.8V) CNL06 RPD is 2.8V Check the connector to LCD panel (CNL04) Samsung Electronics...
Page 37
Check Check Connector the input of V-Sync to LCD Control Assy AC1 Board Check the input Check ICL402 of V-Sync to ICL301 Pin 14 (74HC123) Pin 5 on LCD Control Board Check CNL04 (connector to LCD panel) Samsung Electronics...
Page 38
Exploded View & Parts List 7. Exploded View & Parts List 7-1 SP403JHPX/UMG Code No Description ;Specification Q’ty Remark 1-20 AA61-20217A HOLDER-CHASS/POWER;ABS VO GRAY 1-21 AA95-00228A ASSY-PCB,POWER;SP403JHPX/UMG,M51A,40,-,SAUDI,- 1-22 AA60-10008A SCREW-TAPPING;TH,+,M3,L10,ZPC(YEL),SWRCH18 AA67-70049A SUN-SCREEN;-,SVP-403J,P=0.72,PMMA,-,T=3.0 AA61-20215A HOLDER-SCREEN,SIDE;-,S40LW,HIPS,HB,BLK,- AA67-70051A SCREEN-TINT;-,SVP-403J,P=0.72,PMMA,-,T=3.0 AA61-20214A HOLDER-SCREEN,TOP;-,SVP403J,HIPS,HB,BLK,- 6002-000522 SCREW-TAPPING;TH,+,2,M4,L15,ZPC(BLK),SWRCH18 AA61-20214B HOLDER-SCREEN,TOP;-,SVP403J,HIPS,HB,BLK,-...
Electric Parts List 8. Electric Parts List 8-1 SP403JHPX/UMG Parts List Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark ASSY-PCB,MAIN(OPT) C839 2401-003034 C-AL;220uF,20%,16V,WT,TP,8x11.5,5 C840 2401-003034 C-AL;220uF,20%,16V,WT,TP,8x11.5,5 BUYER : HAD ELECTRO.CO. C841 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0mm, C842 2401-000360 C-AL;100uF,20%,50V,GP,TP,8x11.5,5...
12 V 34 V 34 V 34 V 34 V CN704A CN705A CN602A CN601A CN205 CN206 CN203 CN204 FRONT-C KEYS FRONT-Y FRONT-R FRONT-L SIDE-KEY SIDE-JACK HEAD R HEAD L CN602A CN601A CN205 CN206 CN203 CN204 AUDIO PROCSAN Samsung Electronics 11-1...
@ @ e @ @ e @ @ ? @ @ @ @ ? @ @ e V 4 @ @ ? @ @ @ @ ? @ @ e @ @ e @ @ e V 4 @ 0 Y ? ? @ @ ? ? @ @ ? ? @ @ ? : Power Line : Signal Line Samsung Electronics 12-1...
Page 59
@ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? e ? @ f @ ? @ @ @ @ @ ? Powe L ne S gna L ne 12-2 Samsung Electronics...
Page 60
Schematic Diagrams 12-3 MAIN (POWER) : Power Line : Signal Line Samsung Electronics 12-3...
Page 61
Schematic Diagrams 12-4 PROSCAN (1) : Power Line : Signal Line 12-4 Samsung Electronics...
Page 62
Schematic Diagrams 12-5 PROSCAN (2) : Power Line : Signal Line Samsung Electronics 12-5...
Page 63
Schematic Diagrams 12-6 PROSCAN (3) : Power Line : Signal Line 12-6 Samsung Electronics...
Page 67
Schematic Diagrams 12-10 MAIN (A/V TERMINAL) : Power Line : Signal Line 12-10 Samsung Electronics...
Page 68
? @ @ ? h W & ( ? ' ) X ? @ @ e ? @ @ ? e ? @ @ ? e ? W & ( M I ' ) X ? ? W 2 @ 6 X e @ @ e ? @ @ ? @ @ @ @ @ @ @ @ e W 2 @ @ 6 X : Power Line : Signal Line Samsung Electronics 12-11...
Page 69
@ @ e @ @ e @ @ ? @ @ @ @ ? @ @ e V 4 @ @ ? @ @ @ @ ? @ @ e @ @ e @ @ e V 4 @ 0 Y ? ? @ @ ? ? @ @ ? ? @ @ ? 12-12 Samsung Electronics...
Page 70
V 4 @ @ 0 Y ? @ @ ? @ @ @ @ @ @ ? V 4 @ 0 R 4 @ ? V 4 @ @ 0 Y ? : Power Line : Signal Line Samsung Electronics 12-13...
Page 71
Schematic Diagrams 12-14 MAIN-PIP : Power Line : Signal Line 12-14 Samsung Electronics...
Page 72
Schematic Diagrams 12-15 MAIN SUB (MASTER/REMOCON/PRE-AMP) Samsung Electronics 12-15...