Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system.
Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature.
Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product.
Cleaning Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation.
Power Cable DP cable Dual-Link DVI Cable HDMI cable Analog cable Not all signal cables (Analog, DVI, DP and HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor as below: NOTE: Do not adjust the viewing angle over 21.5 degrees in order to avoid damage.
Connecting the Monitor Cable Connections In Back of Monitor and Computer: Power DVI Dual-Link HDMI Display Port D-SUB Earphone To protect equipment, always turn off the PC and LCD monitor before connecting. Connect the power cable to the AC port on the back of the monitor. (Optional –...
Free-Sync function Free-Sync function is working with DP/HDMI Compatible Graphics Card: Recommend list is as the below, also could be checked by visiting www.AMD.com AMD Radeon RX 400 系列 AMD Radeon R9 300 系列 (370 series except) AMD Radeon R9 Fury X AMD Radeon R9 Nano AMD Radeon R7 360 AMD Radeon R9 295X2...
Adjusting Hotkeys Source/Auto/Exit Game Mode/< Image switch/Volume/> Menu/Enter Power Power Press the power button to turn on/off the monitor. Source/ Auto/ Exit When the OSD is closed, press Source/Auto/Exit button will be Source hot key function. When the OSD is closed, press Source/Auto/Exit button continuously about 2 second to do auto configure (Only for the source with D-Sub).
OSD Setting Basic and simple instruction on the control keys. Press the MENU-button to activate the OSD window. Press< or >to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it . press< or >to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it.
Luminance Press MENU-button to display menu. Press Left or Right to select (Luminance), and press MENU-button to enter. Press Left or Right to select submenu, and press MENU-button to enter. Press Left or Right to adjust. Press AUTO-button to exit Contrast 0-100 Contrast from Digital-register.
Image Setup Press MENU-button to display menu. Press Left or Right to select (Image Setup), and press MENU-button to enter. Press Left or Right to select submenu, and press MENU-button to enter. Press Left or Right to adjust. Press AUTO-button to exit Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise.
Color Setup Press MENU-button to display menu. Press Left or Right to select (Color Setup), and press MENU-button to enter. Press Left or Right to select submenu, and press MENU-button to enter. Press Left or Right to adjust. Press AUTO-button to exit Warm Recall Warm Color Temperature from EEPROM.
Picture Boost Press MENU-button to display menu. Press Left or Right to select (Picture Boost), and press MENU-button to enter. Press Left or Right to select submenu, and press MENU-button to enter. Press Left or Right to adjust. Press AUTO-button to exit Bright Frame on or off Disable or Enable Bright Frame...
OSD Setup Press MENU-button to display menu. Press Left or Right to select (OSD Setup), and press MENU-button to enter. Press Left or Right to select submenu, and press MENU-button to enter. Press Left or Right to adjust. Press AUTO-button to exit Language Select the OSD language Timeout...
Game Setting Press MENU-button to display menu. Press Left or Right to select (Game setting), and press MENU-button to enter. Press Left or Right to select submenu, and press MENU-button to enter. Press Left or Right to adjust. Press AUTO-button to exit For playing FPS (first Person Shooters) games.
Extra Press MENU-button to display menu. Press Left or Right to select (Extra), and press MENU-button to enter. Press Left or Right to select submenu, and press MENU-button to enter. Press Left or Right to adjust. Press AUTO-button to exit Input Select Select Input Signal Source Auto Config...
Exit Press MENU-button to display menu. Press Left or Right to select (Exit), and press MENU-button to enter. Press AUTO-button to exit Exit Exit the main OSD LED Indicator Status LED Color Full Power Mode White Active-off Mode Orange...
Driver i-Menu Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation guide. The software Supported operating systems: Windows 10, Windows 8, Windows 7.
Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).
Screen+ Welcome to “Screen+” software by AOC. Screen+ software is a desktop screen splitting tool; it splits the desktop into different panels, and each panel displays a different window. You only need to drag the window to a corresponding panel when you want to access it. It supports multiple monitor display to make your task easier.
Adjust the maximum resolution and frequency that the monitor can handle properly. Make sure the AOC Monitor Drivers are installed. Adjust the Contrast and Brightness Controls. Press to auto adjust.
Specification General Specification Model name Q3279VWF Driving system TFT Color LCD Viewable Image Size 80.2 cm diagonal Panel Pixel pitch 0. 273 mm (H) x 0. 273 mm (V) Video R, G, B Analog lnterface & DVI&HDMI&DP lnterface Separate Sync.
Page 28
Model name Q3279VWFD8 Driving system TFT Color LCD Viewable Image Size 80.2 cm diagonal Panel Pixel pitch 0. 273 mm (H) x 0. 273 mm (V) Video R, G, B Analog lnterface & DVI&HDMI&DP lnterface Separate Sync. H/V TTL Display Color 10.7 Color 30k - 99kHz(D-SUB/ DVI-Dual-Link) Horizontal scan range...
Pin Assignments 15-Pin Color Display Signal Cable 15-Pin Side of the Signal Cable Pin Number 15-Pin Side of the Signal Cable Pin Number Video-Red Video-Green Ground Video-Blue N.C. N.C. DDC-Serial data Detect Cable H-sync GND-R V-sync GND-G DDC-Serial clock GND-B 24-Pin Color Display Signal Cable Pin No.
Page 31
Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name TMDS Data 2+ TMDS Data 0- DDC/CEC Ground TMDS Data 2 Shield TMDS Clock + +5V Power TMDS Data 2- TMDS Clock Shield Hot Plug Detect TMDS Data 1+ TMDS Clock- TMDS Data 1Shield TMDS Data 1-...
Plug and Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.