Table of Contents
Advertisement
QUICK START GUIDE
QUICK START GUIDE
QUICK START GUIDE
13.Be sure the screws force their way past the opening on
13.Be sure the screws force their way past the opening on
the gasket channel and sit flush against the bottom of
the gasket channel and sit flush against the bottom of
the channel.
the channel.
Integrated Panel
Integrated Panel
14.Remove clamps from door/drawer.
QUICK START GUIDE
14.Remove clamps from door/drawer.
If panel requires additional adjustment after
If panel requires additional adjustment after
removing clamps, slightly loosen each screw and
removing clamps, slightly loosen each screw and
adjust panel as necessary. Tighten screws upon
adjust panel as necessary. Tighten screws upon
completion.
13.Be sure the screws force their way past the opening on
completion.
the gasket channel and sit flush against the bottom of
the channel.
15.Starting at the corners, re-install the gasket into the
15.Starting at the corners, re-install the gasket into the
gasket channel in the frame. Make sure the gasket is
gasket channel in the frame. Make sure the gasket is
fully seated. This may take some force.
fully seated. This may take some force.
Integrated Panel
First Use
First Use
All U-Line controls are preset at the factory. Initial startup
14.Remove clamps from door/drawer.
All U-Line controls are preset at the factory. Initial startup
requires no adjustments.
requires no adjustments.
If panel requires additional adjustment after
NOTICE
removing clamps, slightly loosen each screw and
NOTICE
adjust panel as necessary. Tighten screws upon
U-Line recommends discarding the ice produced
U-Line recommends discarding the ice produced
completion.
during the first two to three hours of operation
during the first two to three hours of operation
to avoid possible dirt or scale that may dislodge
to avoid possible dirt or scale that may dislodge
from the water line.
15.Starting at the corners, re-install the gasket into the
from the water line.
gasket channel in the frame. Make sure the gasket is
fully seated. This may take some force.
To turn the unit on or off:
To turn the unit on or off:
First Use
All U-Line controls are preset at the factory. Initial startup
requires no adjustments.
Press the rocker switch located inside the door on the
Press the rocker switch located inside the door on the
front panel, or behind the grille.
front panel, or behind the grille.
NOTICE
U-Line recommends discarding the ice produced
during the first two to three hours of operation
to avoid possible dirt or scale that may dislodge
from the water line.
Integrated Panel
Integrated Panel
Integrated Panel
Ice
Defrost
Ice
ICE MAKER OPERATION
This unit requires manual defrost, periodically.
ICE MAKER OPERATION
When the ice bucket is full, the ice making mechanism will
When the ice bucket is full, the ice making mechanism will
shut off. However, the refrigeration system will continue
Inspect the interior walls for frost build up every 3 - 4
shut off. However, the refrigeration system will continue
to cool and maintain the ice supply.
weeks. Defrost your unit when 1/4" of frost builds up
to cool and maintain the ice supply.
on the interior walls. Frost will build up faster in humid
environments and when the door is opened frequently.
NOTICE
NOTICE
To defrost, remove ice bucket, turn off unit, leave door
Do not place cans or bottles in the ice
Do not place cans or bottles in the ice
open, and allow frost/ice to melt naturally. Do not use
compartment because they will freeze.
compartment because they will freeze.
tools to chip or scrape the frost as it may damage your
unit. Use a towel to absorb melting frost/ice. Before
turning the unit back on, make sure all the frost is gone
and the unit is dry.
Ice
ICE MAKER OPERATION
When the ice bucket is full, the ice making mechanism will
shut off. However, the refrigeration system will continue
to cool and maintain the ice supply.
To turn off ice production:
NOTICE
To turn off ice production:
an upright and locked position. The unit will preserve
an upright and locked position. The unit will preserve
Do not place cans or bottles in the ice
temperature for ice storage.
temperature for ice storage.
compartment because they will freeze.
NOTICE
NOTICE
If not intending to use the ice maker, turn the
If not intending to use the ice maker, turn the
water supply valve off. It is also important to
water supply valve off. It is also important to
raise the bin arm of the ice maker (see above).
raise the bin arm of the ice maker (see above).
Failure to raise the bin arm may result in damage
Failure to raise the bin arm may result in damage
to the water valve.
to the water valve.
Certain sounds are normal during the unit's operation. You
Certain sounds are normal during the unit's operation. You
may hear the compressor or fan motor, the water valve,
may hear the compressor or fan motor, the water valve,
or ice dropping into the ice bucket.
or ice dropping into the ice bucket.
To turn off ice production:
an upright and locked position. The unit will preserve
CAUTION
!
temperature for ice storage.
CAUTION
!
NEVER use an ice pick, knife or other sharp
NOTICE
NEVER use an ice pick, knife or other sharp
instrument to separate cubes. Shake the ice
instrument to separate cubes. Shake the ice
If not intending to use the ice maker, turn the
bucket instead.
bucket instead.
water supply valve off. It is also important to
raise the bin arm of the ice maker (see above).
Failure to raise the bin arm may result in damage
16
16
to the water valve.
16
u-line.com
u-line.com
u-line.com
u-line.com
OFF
OFF
ON
ON
Raise the bin arm into
Raise the bin arm into
OFF
ON
Raise the bin arm into
Advertisement
Table of Contents
