LG LDG3015SW Installation Manual
Gas double oven range
Hide thumbs
Also See for LDG3015SW:
- Owner's manual (92 pages) ,
- Service manual (84 pages) ,
- Manual de propietario (49 pages)
Table of Contents
Related Manuals for LG LDG3015SW
Summary of Contents for LG LDG3015SW
- Page 1 INSTALLATION MANUAL GAS DOUBLE OVEN RANGE Please read this guide thoroughly before installation. LDG3017ST LDG3037ST LDG3036BD LDG3016ST LDG3036ST LDG3015ST/SB/SW LDG3035ST/SB/SW LDG3011ST LDG3031ST www.lg.com (REV.08 150223) MFL62177703...
-
Page 2: Installation Safety Instructions
INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION INSTALLATION SAFETY INSTRUCTIONS BEFORE YOU BEGIN Read these instructions completely Note to Installer: Leave these instructions with and carefully. the appliance after installation is completed. Note to Consumer: Keep the User’s Guide and Installation of this range must conform with local Installation Instructions for future reference. -
Page 3: Important Safety Instructions
INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION INSTALLATION SAFETY INSTRUCTIONS (continued) BEFORE YOU BEGIN Remove all tape and packing materials before using the range. Dispose of all plastic bags after unpacking the range. Never allow children to play with packing materials. IMPORTANT SAFETY INSTRUCTIONS Read these instructions completely and carefully. - Page 4 INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION INSTALLATION SAFETY INSTRUCTIONS (continued) - If the range is pulled away from the wall for WARNING! cleaning, service, or any other reason, ensure that the Anti-Tip Device is properly reengaged when the • ALL RANGES CAN TIP range is pushed back against the wall.
-
Page 5: In The Commonwealth Of Massachusetts
INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION INSTALLATION SAFETY INSTRUCTIONS (continued) WARNING! • If a 30” clearance between cooking surface and • The vertical distance from the plane of the cooking overhead combustible material or metal cabinets surface to the bottom of adjacent overhead cannot be maintained, protect the underside of cabinets extending closer than 1”... -
Page 6: Dimensions And Clearances
INSTALLATION INSTRUCTIONS DIMENSIONS AND CLEARANCES Provide proper clearances between the range and The range may be placed with 0” clearance (flush) at the adjacent combustible surfaces. These dimensions must back wall. be met for safe use of your range. The location of the electrical outlet and pipe opening (see “GAS PIPE AND ELECTRICAL OUTLET LOCATIONS”) may be adjusted to meet specific requirements. - Page 7 INSTALLATION INSTRUCTIONS LOCATION Do not locate your range where it may be subject to When the floor covering ends at the front of the range, strong drafts. Any openings in the floor or wall behind the area that the range will be installed on should be the range should be sealed.
-
Page 8: Provide Adequate Gas Supply
INSTALLATION INSTRUCTIONS GAS PIPE AND ELECTRICAL OUTLET LOCATIONS 30” 30” ” 1 / 16 ” 3 / 32 2” Recommended area for 120V outlet on rear wall and area for through- ” 19 / 32 the wall connection of pipe stub and 3”... -
Page 9: Connect The Range To Gas
INSTALLATION INSTRUCTIONS 2. CONNECT THE RANGE TO GAS Shut off the range gas supply valve before removing Connect a flexible metal appliance connector to the old range and leave it off until the new hook-up the adapter on the range. Position range to permit has been completed. -
Page 10: Electrical Connections
INSTALLATION INSTRUCTIONS 3. ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS 120 Volt, 60 Hertz, properly grounded dedicated circuit protected by a 15 or 20 Amp circuit breaker, or slow blow fuse. GROUNDING IMPORTANT: FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. The power cord of this appliance is equipped with a 3-prong CAUTION: (grounding) plug which mates with a standard 3-prong grounding wall receptacle to minimize the possibility of electric... -
Page 11: Assemble The Surface Burners
INSTALLATION INSTRUCTIONS 5. ASSEMBLE THE SURFACE BURNERS CAUTION DO NOT Operate the burners without all parts in Hole place. Place the burner caps and heads on the cooktop. Make Electrode sure that the caps and heads are placed in the correct locations. - Page 12 INSTALLATION INSTRUCTIONS 7. ADJUST THE SURFACE BURNER TO THE LOW FLAME(SIMMER) SETTING. 1) Light all surface burners. 2) Turn the knob on the burner being adjusted to “LO”. 3) Remove knob. 4) Insert a small, flat bladed screwdriver into the valve shaft as shown in Fig.
- Page 13 INSTALLATION INSTRUCTIONS 8. CHECK OPERATION OF BAKE/BROIL BURNERS To check ignition of the Bake burner, follow the steps To check ignition of the Broil burner, follow the steps below: below: 1) Remove all packing from inside the oven cavity. 1) Press "Broil" ("Hi" will be shown in the display). 2) Press "Bake"...
-
Page 14: Installing The Anti-Tip Device
INSTALLATION INSTRUCTIONS 10. INSTALLING THE ANTI-TIP DEVICE WARNING INSTALL THE BRACKET USING THE BRACKET INSTALLATION SHEET • Range must be secured with an approved Anti- Tip device. Anti-tip Wall plate bracket • The range could be tipped by standing, sitting or Screw must leaning on an open door if the range or Anti-Tip enter wood or... -
Page 15: When All Hookups Are Complete
INSTALLATION INSTRUCTIONS WHEN ALL HOOKUPS ARE COMPLETE Make sure all controls are left in the off position. Make sure the flow of combustion and ventilation air to the range is unblocked. CONVERTING TO LP GAS (OR CONVERTING BACK TO NATURAL GAS FROM LP) This range leaves the factory set for use with natural The conversion instructions and LP orifices can be found gas. - Page 16 Memo...