Transporting Lithium Batteries; Residual Risks; Risk Reduction - Ryobi RCD1201 Original Instructions Manual

■ The recommended ambient temperature range for the
charging system during charging is between 10°C and
38°C.
ADDItIOnAL BAtteRY sAFetY WARnInGs
WARnInG
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■ Ambient temperature range for battery during use is
between 0°C and 40°C.
■ Ambient temperature range for battery storage is
between 0°C and 20°C.

tRAnsPORtInG LItHIuM BAtteRIes

Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

ResIDuAL RIsKs

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■ Damage to hearing caused by noise
– Wear suitable hearing protection and limit exposure.
■ Injury to the eyes
– Wear protective eye shields or goggles when using
the product.
■ Injury caused by vibration
– Limit exposure. Follow the instructions in Risk
Reduction.
■ Electric shock caused by contact with hidden wires
– Hold the product only by insulated surfaces.
■ Injury caused by dust
– Dust created by operating the product can cause
respiratory injury. Wear appropriate dust control
mask with filters suitable for protecting against
particles from the material being worked on.

RIsK ReDuCtIOn

It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■ Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
■ After each period of operation, exercise to increase
blood circulation.
■ Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARnInG
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
KnOW YOuR PRODuCt
See page 5.
1. Keyless chuck
2. Torque adjustment ring
3. LED Indicator (Fuel gauge)
4. Forward / reverse button
5. Switch trigger
6. Battery port
7. Handle, insulated gripping surface
MAIntenAnCe
■ When servicing, use only identical RYOBI replacement
parts. Use of any other parts may create a hazard or
cause product damage.
■ Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, dust, oil, grease,
etc.
■ Do not attempt to modify this tool or create accessories
not recommended for use with this tool.
Safety
3