Page 2 TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE Information in this manual is subject to change without notice.
Page 3 Regulations Information Class B Regulations Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 4 Please note: The use of a non-shielded interface cable with this equipment is prohibited. Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Page 5 SAFE USAGE NOTIFIATION: For reasons of personal safety and optimal radio performance, Motorola has designed the ML850 with an intended purpose and position of use either in a secured vehicle docking station or on the to of an office desk.
Page 6 About the Battery Caution Texts Concerning Lithium Batteries DANISH ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. NORWEGIAN ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten.
Page 7 CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ.
Page 8 FRENCH ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant.
Page 9 Caution (for USA Users) To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P) configuration;...
Page 10: Table Of Contents
Table of Contents Preface ..................v Chapter 1 ............Getting Started 1-1 Getting the Computer Running..........1-2 Unpacking ................1-2 Connecting to AC Power ...........1-2 Opening the Cover .............1-3 Closing the Cover ..............1-4 Turning On and Off the Computer........1-4 Taking a Look at the Computer ..........1-5 Right-side Components............1-5 Left-side Components ............1-7 Rear Components...............1-8...
Page 11 Chapter 2 .......... Operating Your Computer 2-1 Starting and Stopping the Computer........2-2 Starting the Computer ............2-2 Stopping the Computer ............2-2 Using the Keyboard ..............2-4 Typewriter Keys..............2-4 Cursor-control Keys ............2-4 Numeric Keypad ..............2-5 Euro Symbol...............2-5 Function Keys ..............2-5 Fn Key................2-6 Hot keys ................2-6 Using the Touchpad ..............2-8 Configuring the Touchpad ..........2-9 Using the Touchscreen (optional)..........2-10...
Page 12 Using the Communication Features........2-21 Using the Modem.............2-21 Using the LAN..............2-21 Using the Wireless LAN............2-22 Configuing the Wireless LAN .........2-22 Unstall & Remove SIM Card ..........2-23 Chapter 3 ............Managing Power 3-1 AC and Car Adapter ..............3-2 Battery Pack................3-3 Charging the Battery Pack ..........3-3 Initializing the Battery Pack..........3-4 Checking the Battery Level..........3-4 Replacing the Battery Pack ..........3-4...
Page 13 Inserting and Removing a PC Card........4-6 System Memory Upgrade ............4-7 Chapter 5 ......Setup Configuration Utility (SCU) 5-1 When and How to Use the SCU Program........5-2 When to Use...............5-2 Starting SCU ..............5-2 Moving Around and Making Selections ......5-4 Main Menu................5-5 Date and Time ..............5-5 Intelnal and Numlock ............5-6 USB Emulation ..............5-6...
Page 14 Load Previous Values ............5-13 Chapter 6 ............Installing Software 6-1 How to Use the CD..............6-2 Imaging the HDD ..............6-3 Installing Device Drivers for Windows 2000/Windows XP ...6-4 Installing Touch Screen Driver for Windows 2000....6-6 Installing Drivers for Windows XP .........6-7 Installing Touch Screen Driver for Windows XP....6-8 Touchscreen Utility ...............6-18 Chapter 7 ..........Caring for the Computer 7-1...
Page 15: Preface
CD/DVD/COMBO Drive Problems (on optional docking station)................8-5 Display Problems ...............8-5 Floppy Disk Drive Problems (on optional docking station)8-7 Hardware Device Problems..........8-8 Hard Disk Drive Problems ..........8-8 Keyboard, Mouse, and Touchpad Problems ......8-9 LAN Problems ..............8-10 Wireless LAN Problems ..........8-10 Modem Problems .............8-11 PC Card Problems ............8-11 Power Management Problems (for Windows) ....8-11 Printer Problems (connected through optional docking...
Page 16 Chapter 2, Operating Your Computer, tells you how to use the computer’s components and features. Chapter 3, Managing Power, provides information on power. Chapter 4, Expanding Your Computer, provides information on installing and using peripheral devices. Chapter 5, SCU (Setup Configuration Utility), describes the SCU program that configures the computer’s BIOS settings.
Page 17 Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information which, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset.
Page 18 Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive, royalty free license to use that arises by operation of law in the sale of a product.
Page 19 Three (3)Years from the date of shipment. Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it with the same or equivalent...
Page 20 Motorola cannot be responsible in any way for any ancillary equipment not furnished by Motorola which is attached to or used in connection with the product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty.
Page 21 (including, without limitation, the addition to the Product of non-Motorola supplied equipment) which adversely affect performance of the Product or interfere with Motorola’s normal warranty inspection and testing of the Product to verify any warranty claim. F) Product which has had the serial number removed or made illegible.
Page 22 A) That Motorola will be notified promptly in writing by such purchaser of any notice of such claim; B) That Motorola will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C) Should the Product or its parts become, or in Motorola’s opinion...
Page 23 Motorola will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or its parts furnished hereunder with software, apparatus or devices not furnished by Motorola, nor will Motorola have any liability for the use of ancillary equipment or software not furnished by Motorola which is attached to or used in connection with the Product.
Page 24 Trademarks Motorola and the Motorola logo are registered trademarks of Motorola Inc. Mobile Laptop 850 are trademarks of Motorola. Microsoft, MS-DOS, MS-Windows, and Windows are registered trademarks of Microsoft Corporation.
Page 25: Chapter 1
CHAPTER 1 Getting Started Congratulations on purchasing this industrial notebook computer. It’s rugged, compact, and portable design allows you to use it in the field or inside a vehicle and other demanding situations where conventional notebook computers just cannot measure up. It can also connect with a docking station to extend the capabilities of input/output devices.
Page 26: Getting The Computer Running
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: Notebook Computer Accessories: − AC adapter (100~240 VAC, 50~60 Hz) −...
Page 27: Opening The Cover
1. Make sure the computer is turned off. 2. Plug the DC cord of the AC adapter to the power connector on the computer. NOTE: When the computer is attached to the docking station, connect the DC cord to the power connector on the docking station instead. 3.
Page 28: Closing The Cover
Closing the Cover When closing the cover, make sure that the hook is latched properly to safeguard against the following: To prevent damage to the LCD screen during transport. To prevent the computer from accidentally waking up from Suspend mode during transport without the user’s knowledge.
Page 29: Taking A Look At The Computer
Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “Stopping the Computer” in Chapter 2 for information.) CAUTION: If you have to turn the computer on again immediately after turning it off, wait for at least five seconds.
Page 30 Component Description See Also Battery Charge Indicator: – glows green when the battery is fully charged. – Glows orange when the battery is being charged. – Is dark when battery has no charge left and AC adapter is connected and powered on.
Page 31: Left-Side Components
Left-Side Components Component Description See Also Audio Output Connects a hi-fi set, radio set, synthesizer, Connector walkman, etc. Microphone In Connects an external microphone. Connector Getting Started...
Page 32: Rear Components
Rear Components Component Description See Also USB Port Each of the two ports connects a USB device, such as a USB floppy drive, printer, digital camera, joystick, and more. VGA Port Connects an external monitor. Serial Port Connects a serial device, such as mouse. Power Connects the AC adapter.
Page 33: Front Components
Front Components Component Description See Also Notched Hole Allows you to hook the computer to the docking station. Serves as the antenna for the optional Wireless wireless modem or GSM. Modem or GSM Antenna Touchscreen Provides a convenient way to use the touchscreen.
Page 34 Component Description See Also Speaker Sends out sound and voice from the computer. Battery Open the cover to access the battery pack. Compartment Cover Battery Cover Locks the battery compartment. Latch Docking Serves as the interface between the docking Connector station and the computer.
Page 35: Top-Open Components
Top-Open Components Component Description See Also LCD Screen Displays the output of the computer. Device Indicators Shows the current status of the computer’s devices. Caps Lock Indicator – glows green when Caps Lock key is pressed and its function is activated.
Page 36 LAN 10/100 Indicator – glows orange when LAN speed is 10 MBPS – glows green when LAN speed is 100 MBPS Hard Disk Drive Indicator (includes Floppy Disk Drive or CD-ROM Drive In-use Indicator when computer is connected to docking station) Keyboard Serves as the data input device of the computer.
Page 37: Chapter 2
CHAPTER 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Page 38: Starting And Stopping The Computer
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk;...
Page 39 To stop in Do this… To start up or this mode… resume again Depending on your settings in Windows, Suspend Press the power you can place the computer in Suspend button. mode by pressing the power button or by closing the display cover. If you choose to stop in Standby or Suspend mode, you can return to where you left off the next time you start up the computer.
Page 40: Using The Keyboard
Using the Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus a key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: Typewriter keys Cursor-control keys Numeric keys Function keys Typewriter Keys...
Page 41: Numeric Keypad
Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate entering of numbers and calculations. Num Lk When is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTE: When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num.
Page 42: Fn Key
Function Keys On the top row of the keys are the function keys: . Function keys are multi-purpose keys that perform functions defined by individual programs. Hot key functions are assigned to , and your computer. (See “Hot Keys” section in this chapter for information.) Fn.
Page 43 Description Fn+F9 Switches the display output to one of the following three when an external CRT monitor is connected through the docking station. CRT monitor Display on both NOTE: If the display mode is set to 256 colors or lower, or in DOS mode, there will be only two modes for selecting: CRT only and Display on both.
Page 44: Using The Touchpad
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force. The touchpad is a pointing device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Page 45: Configuring The Touchpad
Term Action Drag and Press and hold the left button, then move your fingers drop until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
Page 46: Using The Touchscreen (Optional)
Using the Touchscreen (Optional) CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. Use the included touchscreen pen instead, which can be stretched for better grip and handling. The touchscreen is a touch-sensitive device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons.
Page 47: Configuring The Touchscreen
Term Action Scroll To scroll is to move up and down or left and right in the working area on the screen. To move vertically, place your finger or pen on the right edge of the touchscreen and slide your finger or pen up and down along the edge.
Page 48: Using The Floppy Disk Drive (Optional)
Using the Floppy Disk Drive (optional) Your computer may come with the optional floppy disk drive as drive A through the optional docking station. A floppy disk drive allows you to install new programs into your computer, or to store information on a removable floppy disk so you can transfer information from one computer to another.
Page 49: Inserting And Ejecting Floppy Disks
Inserting and Ejecting Floppy Disks To insert a floppy disk, hold it with the arrow facing up and towards the drive. Slide the disk into the drive until it clicks into place. To eject a floppy disk, first ensure that the floppy disk drive in-use indicator is off, and then press the eject button on the drive.
Page 50: Using The Hard Disk Drive
Using the Hard Disk Drive Your computer comes with a hard disk drive as drive C. A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch IDE (Integrated Drive Electronics) hard disk drive.
Page 51: Using The Cd/Dvd/Combo Drive (Optional)
Using the CD/DVD Drive (optional) Your computer may come with an optional CD-ROM drive, COMBO drives, or DVD-ROM drives through the optional docking station. This drive is usually configured as drive D. The drive uses removable 5.25-inch silver CD-ROM discs, which look like standard music CDs.
Page 52: Inserting And Removing A Cd
Inserting and removing a CD Follow this procedure to insert or remove a CD. 1. Turn on the computer. 2. Press the eject button and the CD tray will slide out partially. Gently pull it until fully extended. 3. To insert a CD, put down the CD in the tray with its label facing up. Slightly press the center of the CD until it clicks into place.
Page 53: Using The Video Features
Using the Video Features The video subsystem of your computer features: 12.1-inch TFT (Thin-Film Transistor) color LCD display with 1024x768 XGA (Extended Video Graphics Array) resolution. Sunlight Readable Panel , Transflective LCD (Optional). Simultaneous display on LCD and external monitor (connect through the docking station), which is useful when you have a presentation as you can control the screen from your computer and face the audience at the same time.
Page 54 Simultaneous Display Mode LCD Only CRT Only Display Resolution Colors √ √ √ 640x480 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ √ √ 720x480 8-bit √ √ √ 16-bit √ √ √ 24-bit √...
Page 55 Simultaneous Display Mode Display LCD Only CRT Only √ √ √ 1024x768 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 32-bit √ 1152x864 8-bit √ 16-bit √ 24-bit √ 32-bit √ 1280x1024 8-bit √ 16-bit √ 24-bit √...
Page 56: Using The Audio Features
Using the Audio Features NOTE: To take advantage of the enhanced audio capabilities, the audio driver supplied with your computer must be installed. If you experience interference while recording, try lowering the microphone recording volume. The audio subsystem of your computer features: Digital audio and analog mixing functions required for recording and playing sound on your computer SoundBlaster Pro, Adlib, and Microsoft Windows Sound System...
Page 57: Using The Communication Features
Using the Communication Features Using the Modem NOTE: To take advantage of the modem feature, the modem driver supplied with your computer must be installed. The internal 56 K fax/data modem allows you to use the telephone line to communicate with others by fax, email, or connect to an online service or bulletin board.
Page 58: Using The Wireless Lan
Using the Wireless LAN Depending on your model, an internal Mini PCI wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you access corporate networks or the Internet in a wireless environment. The WLAN features include: IEEE 802.11b or 802.11bg standard compliance 2.4 GHz DSSS (Direct Seque.
Page 59: Chapter 3
CHAPTER Managing Power Your computer operates either on external AC power or internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way. The topics in this chapter include: What is an AC adapter How to charge the battery pack...
Page 60 AC Adapter CAUTION: The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. The AC power cord supplied with your computer is for use in the country where you purchased your computer.
Page 61: Battery Pack
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time.
Page 62: Initializing The Battery Pack
To charge the battery pack, connect the AC adapter to the computer and an electrical outlet. The Battery Charge Indicator ( ) on the computer glows amber to indicate that charging is in progress. You are advised to keep the computer power off while the battery is being charged. When the battery is fully charged, the Battery Charge Indicator glows green.
Page 63: Replacing The Battery Pack
Replacing the Battery Pack CAUTION: There is danger of explosion if the battery is incorrectly replaced. Replace the battery only with the computer manufacturer’s optional battery packs. Discard used batteries according to the dealer’s instructions. Do not attempt to disassemble the battery pack. battery leak and the fluid get into eyes, not rub eyes...
Page 64 4. Pull the battery pack. Battery Pack 5. Pull on the protruding strip to slide the battery pack to the left and lift the battery pack out of its compartment. Pull battery pack 6. Insert the new battery into the compartment and slide the battery pack to the right to allow the proper connection of connectors.
Page 65: Battery Low Signals And Actions
Battery Low Signals and Actions Battery Low occurs when the battery has approximately 10% (Windows default setting) of its charge remaining. The computer in the Battery Indicator LED blink to alert you to take actions. NOTE: You can set up your threshold and signals of Battery Low under Windows. Immediately save your data upon Battery Low.
Page 66: Power Management
Power Management Your computer supports APM ( Advanced Power Management) and ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows 2000 and Windows XP, power supply to different computer components is controlled on an as-needed basis.
Page 67 Manual Power Management You can manually initiate Suspend-to-disk mode at any time in one of two ways: Use the O/S that supports the Suspend function. Press down the power button and release it in less than 4 seconds with the system on. Repeat the action to wake up the system under Suspend mode.
Page 68: Power-Saving Tips
Power-Saving Tips In addition to your computer’s automatic power management, you can do your part to maximize the battery’s operating time by following these suggestions. Do not disable Power Management. Decrease the LCD brightness to the lowest comfortable level. Disable the parallel and serial ports if no devices are connected to these ports.
Page 69: Chapter 4
CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter. This chapter gives guidelines on installing and using these devices: External monitor Parallel device (through the optional docking station) Serial device...
Page 70: Connecting An External Monitor (Optional)
Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external CRT monitor to your computer through the optional docking station. Follow this procedure to connect an external monitor: 1.
Page 71: Connecting A Parallel Device (Optional)
Connecting a Parallel Device (optional) The optional docking station has a p arallel port for connecting a parallel device such as printer. The port supports ECP (Extended Capabilities Port) and EPP (Enhanced Parallel Port) modes that turn the standard parallel port into a high-speed bi-directional peripheral port.
Page 72: Connecting A Serial Device
Connecting a Serial Device Your computer has a serial port for connecting a serial device such as a serial mouse or modem. Follow this procedure to connect a serial device: 1. Make sure the “COM1 Port” item is set properly in the SCU program. (See “Advanced Menu”...
Page 73: Connecting A Usb Device (Usb 2.0)
Connecting a USB Device (USB 2.0) Your computer has one USB port on the right side for connecting USB 2.0 devices such as digital camera, scanner, printer, modem, or mouse and two USB ports on the left side of the optional docking station.
Page 74: Using Pc Cards
Using PC Cards Your computer has one PC Card slot to accommodate one type II card. ZV Port and CardBus Support Your computer’s PC Card slot supports CardBus and ZV (Zoomed-Video) Port specifications. CardBus is the 32-bit version of PC Card technology. It allows speeds of up to 133 Mbps at 33 MHz.
Page 75: System Memory Upgrade
To remove a PC Card: 1. Your operating system may require you to stop the PC Card before you actually remove it. (In Windows, double-click the PC Card icon in Control Panel to stop the card.) 2. Push the eject button and the card will slide out slightly. 3.
Page 76 Expanding Your Computer...
Page 77 CHAPTER 5 Setup Configuration Utility (SCU) SCU is a program for configuring the BIOS (Basic input/output System) settings of the computer. BIOS are a layer of software, called firmware that translates instructions from other layers of software into instructions that the computer hardware can understand.
Page 78: When And How To Use The Scu Program
When and How to Use the SCU Program When to Use You need to run the SCU program when: You see an error message on the screen requesting you to run Setup. You want to restore the factory default settings. You want to modify some specific settings according to the hardware.
Page 79 The menu can be divided into four areas: On the top line is the menu bar containing the titles of the available menus. Each menu title brings a specific menu. The center left column of the menu contains items that you can set for the selected menu title.
Page 80: Moving Around And Making Selections
Moving Around and Making Selections A brief description of keyboard usage is listed next: Function ←, → Selects a menu title. ↑, ↓ Selects an item or option. Enter Opens or closes the options window when an item is selected. Space bar, Cycles through the pre-defined value for the selected item.
Page 81: Main Menu
Main Menu The Main menu contains the basic configuration settings of the system. Date and Time Sets the system date and time. Setup Configuration Utility...
Page 82: Intelnal And Numlock
Internal and Numlock sets if you can enter a number when Num Lock is turn off. When this item is enabled, you can press and hold FN, and then press a letter key to enter a number even if Num Lock is turned off. When this is disabled, you cannot enter a number with the above method.
Page 83: Advanced Menu
Advanced Menu The Advanced menu contains the input/output configuration settings of the system. Geyserville Support Enables or disables the Geyserville feature of the CPU. The Geyserville feature helps conserve battery life by decreasing the CPU’s running speed under certain conditions while still maintaining a high performance.
Page 84: Shared Video Memory
Shared Video Memory sets the shared memory size of the video controller. The options are 4M, 8M, 16M and 32M. Com Ports Setup Configuration Utility...
Page 85: Hdd Heater
HDD Heater A new feature creates safe and reliable operating conditions for the Hard Disk Drive (HDD) in excessive cold temperature conditions (-20°). The feature will allow flexible configurable settings to customize the operational parameters of the HDD heater. Basically, there are two stage to from heating function. The first stage increases HDD temperature 0.7°C per minute.
Page 86: Security Menu
Security Menu The Security menu contains the security setting that safeguards your system against unauthorized use. Power-on Password Set Password allows you to set the password for your system. When typing password, first make sure that Num Lock is off, then type your password in the entry fields and press Enter.
Page 87: Set Password
SCU Password Set Password allows you to set the password for your system. When typing password, first make sure that Num Lock is off, then type your password in the entry fields and press Enter. Confirm your password by typing it again and pressing Enter. If the Enable Password to SCU sub-item is enabled, the set password is always required to enter SCU.
Page 88: Boot Menu
Boot Menu The Boot men sets the sequence of the devices to be searched for the operating system. Boot Sequence sets the first, second, third, and fourth booting devices. The system will try to boot from the first device but if it is not available, will try the next boot device.
Page 89: Exit Menu
Exit Menu The Exit menu displays ways of exiting SCU. After finished with your setting, you must save and exit so that the new setting can take effect. Save Change and Exit saves the changes you have made and exits SCU.
Page 90 5-14 Setup Configuration Utility...
Page 91 CHAPTER 6 Installing Software To take full advantage of the unique features of your computer, some operating systems require custom software, known as drivers, to be installed. If you purchased the computer with Windows pre-installed; your dealer may have already installed the drivers. If not, you need to install the drivers using the CD supplied with your computer.
Page 92: How To Use The Cd
How to Use the CD NOTES: • The drivers may have been updated after this manual was published. For driver’s upgrade, please contact your dealer. • You can always find README or document files on the CD. These files contain the latest information from the software supplier.
Page 93: Imaging The Hdd
Imaging the HDD Motorola recommends using the following methods for extracting or installing hard disk images on the Motorola ML850. a. (Install or Extract) To install or extract HDD images from/to the Motorola ML850 Motorola recommends using Symantec Ghost(tm) Multi-Cast server via Ethernet. This functionality is provided in the Symantec Ghost(tm) Corporate Edition.
Page 94 Install Device Driver for Windows 2000/Windows XP To install the necessary driver, just click on the particular option and follow the onscreen instructions to continue and complete installation. Device Driver Press the “Device driver” button, the system will auto install include VGA, Audio, Modem, LAN , Wireless LAN, USB 2.0, DirectX 8.1, Chipset driver etc.
Page 95 Allows you to select high-resolution displays with richer colors. It can drive CD displays as well as CRT displays. Audio Allows you to take full advantage of the audio subsystem. Modem The modem driver allows you to transmit information over a standard telephone line through RJ-11 port. Speedstep Press the Speedstep button, the system will auto install for Window 2000.
Page 96: Installing Touch Screen Driver For Windows 2000
Install Touch Screen Driver for Windows 2000 Insert the driver CD into the drive. Click on “TOUCH SCREEN” then “WIN2000”, and follow the onscreen instructions to continue. When finished installing, select “Yes” to reboot your system. The driver should now be loaded. After the system has finished rebooting, click on the “PenMount Monitor”...
Page 97: Installing Drivers For Windows Xp
Installing Drivers for Windows XP To set up the necessary drivers for Windows XP, click on “TOUCH SCREEN ” on the initial screen. The following screen appears: Installing Software Drivers...
Page 98: Installing Touch Screen Driver For Windows Xp
Install Touch Screen Driver for Windows XP Hardware Install: (1) Insert the driver CD to the CD drive, to bring up the following screen. Select “WINXP”. Click on “TouchScreen” to continue and follow the on screen instruction to continue. Installing Software Drivers...
Page 99 (2) When the TSRC-XP.htm file appear, then select ”START” -> “Control Panel” button. Installing Software Drivers...
Page 100 (3) When the “Control Panel “ screen appear, then click on “ performance and Maintenance” button. 6-10 Installing Software Drivers...
Page 101 (4) When the “Performance and Maintenance” screen appear, and then click on “System” button. 6-11 Installing Software Drivers...
Page 102 (5) When the “System Properties” screen appear, and then click on “Hardware” and “Device Manager “ button. 6-12 Installing Software Drivers...
Page 103 (6) When the “Device Manager” screen appear, then click on “ ?Unknown device” and then click on the “Properties” icon. 6-13 Installing Software Drivers...
Page 104 (7) When the “Unknown Device Properties” screen appear, and then click on “ Reinstall Driver” button. 6-14 Installing Software Drivers...
Page 105 (8) When the “Hardware Update Wizard” appears, click on “ Install the software automatically [Recommand], then click on ”Next”. (9) When the “Hardware Installation” screen appears, click on ”Continue Anyway”. 6-15 Installing Software Drivers...
Page 106 (10) When the “Hardware Update Wizard”screen appears, click on ”Finish” button. 6-16 Installing Software Drivers...
Page 107 (11) When the “PenMount DMC9000 and DMC9100 Properties”screen appears, click on ”Close” button to exit the driver installation.. 6-17 Installing Software Drivers...
Page 108: Touchscreen Utility
Touchscreen Utility To install the touchscreen utility, perform the following: (1) Insert the driver CD to the CD drive, to bring up the following screen. (2) Click on “Start” then “Run”. 6-18 Installing Software Drivers...
Page 109 (3) Enter the following directory on the driver CD: \TOUCHSCREEN\Setup.exe, then click on “OK”. (4) Select “Yes” to the question if this is the first time to run this setup. (5) When the “InstallShield Wizard” appears, click on “Next” to continue. (6) Select “...
Page 110 (10) When the “PENMOUNT Control Panel” dialog box appears, click on the “Calibrate” folder and click on the “Calibrate” button. (11) If you need 4,9,16,25 dot of the calibrate, we suggest select “ Advanced Calibrate” button to calibrate. (12) Click on the four sides red points and plus sign on the screen to calibrate your “PENMOUNT”...
Page 111: Chapter 7
CHAPTER Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer. This chapter gives you guidelines covering these areas of maintenance: How to protect the computer What to note when using and storing the computer How to clean the computer What to note when using the battery pack...
Page 112: Protecting The Computer
Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Password The power-on password protects your computer against unauthorized use.
Page 113: Taking Care Of The Computer
Taking Care of the Computer Location Guidelines Use the computer where the temperature is between 0 °C (32 °F) and 55 °C (131 °F). Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust.
Page 114: Cleaning Guidelines
Cleaning Guidelines Never clean the computer with its power on. Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. Gently wipe the display with a soft, lint-free cloth. Do not use alcohol or detergent on the display.
Page 115: When Traveling
Do not leave the battery pack in storage for more than 3 months without recharging it. If the battery pack has been left unused for a long period of time, or if the battery has deteriorated, the remaining battery capacity may not be displayed accurately.
Page 116 If you plan to travel abroad with your computer, consult your dealer for the appropriate AC power cord for use in your country of destination. Caring for the Computer...
Page 117: Chapter 8
CHAPTER Troubleshooting Hardware, software, or a combination of both can cause computer problems. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Page 118: Preliminary Checklist
Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: Try to isolate which part of the computer is causing the problem. Make sure that you turn on all peripheral devices before turning on the computer.
Page 119: Solving Common Problems
Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery problems P. 8-4 CD/DVD/COMBO drive problems (on optional docking P. 8-5 station) Display problems P. 8-5 Floppy disk drive problems (on optional docking station) P.
Page 120: Battery Problems
Battery Problems The battery does not charge (Battery Charge indicator does not light amber). Make sure that the AC adapter is properly connected. Make sure that the battery is not too hot-getsabove 55°C or to cold- below 0°C. Allow time for the battery pack to return to room temperature.
Page 121: Cd/Dvd/Combo Drive Problems (On Optional Docking Station)
CD / DVD/COMBO Drive Problems (on optional docking station) The CD R-W / DVD-Combo drive cannot read a CD. Make sure that the CD is correctly seated in the tray, with the label facing up. Make sure that the CD is not dirty. Clean the CD with a CD cleaning kit, available in most computer stores.
Page 122 The brightness level might be too low. Increase brightness by Fn+F6 pressing The display output might be set to an external monitor. To switch the display back to the LCD, press Ctrl Reset the computer by pressing the keys if you are using an external keyboard.
Page 123: Floppy Disk Drive Problems (On Optional Docking Station)8-7
The external monitor displays nothing. Make sure that the monitor is turned on. Make sure that the monitor’s signal cable is properly connected. Check if the Setup item Display Mode on the Main menu of the SCU program is configured correctly. Switch the display to the monitor by pressing or change the display through the settings in Display Properties.
Page 124: Hardware Device Problems
Hardware Device Problems The computer does not recognize a newly installed device. The device may not be correctly configured in the SCU program. Run the SCU program to identify the new type. Make sure if any device driver needs to be installed. (Refer to the documentation that came with the device.) Make sure if the device needs any jumper or switch settings.
Page 125: Keyboard, Mouse And Touchpad Problems
Keyboard, Mouse and Touchpad Problems The keyboard does not respond. Try connecting an external keyboard. If it works, contact an authorized dealer, as the internal keyboard cable might be loose. The numeric keypad is disabled. Num Lk Num Lk LED Make sure that the is switched on.
Page 126 WLAN Problems I cannot use the WLAN feature. Make sure that the Mini PCI WLAN card is correctly installed. Make sure that the necessary driver(s) is correctly installed. Make sure that the WLAN feature is turned on. Transmission quality is poor. Your computer may be in an out-of-range situation.
Page 127: Modem Problems
If the operating radio channel is in poor quality, change the Access Point and all the wireless station(s) within the BSSID to another radio channel. Your computer may be in an out-of-range situation. Move your computer closer to the Access Point it is associated with. Make sure that your computer is configured with the same security option (encryption) to the Access Point.
Page 128: Pc Card Problems
PC Card Problems The PC Card does not work. Make sure that the PC Card is correctly seated. If the card requires an IRQ (interrupt request), make sure that there is one available. The PC Card may be attempting to use a COM port in a manner that conflicts with the COM port being used by another device.
Page 129: Printer Problems (Connected Through Optional Docking Station)
The computer does not enter Standby or Suspend mode immediately. If the computer is performing an operation, it normally waits for the operation to finish. The computer does not resume from Standby or Suspend mode. The computer automatically enters Standby or Suspend mode when the battery pack is empty.
Page 130: Software Problems
Software Problems An application program does not work correctly. Make sure that the software is correctly installed. If an error message appears on the screen, consult the software program’s documentation for further information. If you are sure the operation has stop, reset the computer. (See “Resetting the Computer”...
Page 131: Startup Problems
Startup Problems When you turn on the computer, it does not respond and the Power Indicator does not light green. If you are using an external AC power, make sure that the AC adapter is correctly and securely connected. If so, make sure that the electrical outlet works properly.
Page 132: Other Problems
Other Problems The date/time is incorrect. Correct the date and time via the operating system or SCU program. After you have performed everything as described above and still have the incorrect date and time every time you turn on the computer, the RTC (Real-Time Clock) battery is at the end of its life.
Page 133: Appendix A Specifications
APPENDIX Specifications NOTE: Specifications are subject to change without any prior notices. Parts Specifications Intel Dothan LV 1.4GHz in µ-FCBGA package, 400MHz FSB Core logic Intel 855GM chipset + ICH4-M System BIOS 512KB Flash EEPROM Includes System BIOS, VGA BIOS, plug & play, and ACPI 2.0 capability Boot from IDE devices and LAN, USB CD-ROM Suspend to DRAM / HDD...
Page 134 ‧ Standard: 20GB, Integrated, Support Ultra DMA-33/66/100 2.5” 9.5mm height with damper protect ‧ Options: 40GB/60GB HDD heater is option Keyboard Water-proof membrane keyboard Rubber keyboard with back-light (Optional) Pointing device A touch-sensitive control pad with Microsoft Win Mouse function coexist PCMCIA Device Type II x 1...
Page 135 Specifications Parts I/O ports On computer Serial Port × 1 VGA Port × 1 USB 2.0 port × 2 DC input x1 Docking Port x1 RJ-11x1 for 56Kbps Software Modem port RJ-45 100 Base-T LAN port Microphone-in & Earphone out ports Office Docking Station Serial Port ×...

This manual is also suitable for:

L3391b L3392b

Motorola Mobile Laptop 850 Owner's Manual

Chapter 1

Chapter 2

Chapter 3

Chapter 4

Chapter 7

Chapter 8

Appendix A Specifications

Quick Links

Related Manuals for Motorola Mobile Laptop 850

Summary of Contents for Motorola Mobile Laptop 850

This manual is also suitable for:

Table of Contents