Related Manuals for LG LMV2055ST
Summary of Contents for LG LMV2055ST
- Page 1 Website: http://www.lg.com MICROWAVE OVEN INSTALLATION INSTRUCTIONS PLEASE READ AND SAVE THESE INSTALLATION INSTRUCTIONS. MFL37192905...
-
Page 2: Your Safety First
Your Safety First BEFORE YOU START • Proper installation is the installer's responsibility! Proper installation by a qualified technician or installer is recommended. – Read the entire manual before you begin. The model number label is located on the oven front. See Figure 1. - Page 3 Your Safety First SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE. • DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY! – DO NOT try to operate the microwave oven with the door open. – DO NOT tamper with or defeat the safety interlocks. –...
-
Page 4: Parts, Tools, Materials
Parts, Tools, Materials THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector One power cord clamp and (for roof venting or wall venting installation) One dark-colored mounting screw Not Actual Size (2 pieces must be assembled as (to hold the power cord) shown) Not used if venting into kitchen. - Page 5 Parts, Tools, Materials You will need the following tools and materials for the installation: Carton or other heavy material such as a blanket for covering the counter top. Clear Tape Stud Finder or Thin Nail (for taping the templates to the wall) Keyhole Saw (for the power cord hole) Saber Saw (for cutting vent holes for roof...
-
Page 6: Step 1: Prepare The Electrical Connection
STEP 1: Prepare The Electrical Connection W A R N I N G AVOID ELECTRIC SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 5. Upper Cabinet NOTE: The outlet should be on a circuit dedicated to the... -
Page 7: Step 2: Prepare The Venting System
STEP 2: Prepare The Venting System NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 10, page 8. W A R N I N G THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways. - Page 8 STEP 2: Prepare The Venting System Standard Fittings NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper’s sticking. Duct Length The total length of the duct system, including straight duct, elbows, transitions, and wall or roof caps must not exceed 140 feet.
-
Page 9: Step 3: Prepare The Venting Blower
STEP 3: Prepare The Venting Blower roof-venting. You need to adjust the blower if you Your microwave oven is shipped with the blower assembled for want wall-venting or room-venting installation. W A R N I N G ELECTRIC SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT. •... - Page 10 STEP 3: Prepare The Venting Blower Blower Plate Mounting Screw WALL-VENTING INSTALLATION: 1. Remove one or two blower unit mounting screw(s) and one Blower Plate or several blower plate mounting screw(s). Remove the Back Plate Blower Unit blower plate from the cabinet. See Figure 13. 2.
- Page 11 STEP 3: Prepare The Venting Blower ROOM-VENTING (Recirculating) Blower Plate Mounting Screw INSTALLATION: Blower Plate 1. Remove one or two blower unit mounting screw(s) Back Plate and one or several blower plate mounting screw(s). Blower Unit Remove the blower plate. See Figure21. Blower Unit 2.
-
Page 12: Step 4: Prepare The Wall & Upper Cabinet
STEP 4: Prepare The Wall & Upper Cabinet W A R N I N G To avoid personal injury or property damage, do not attempt to install this microwave oven if you cannot find a wall stud. Consult a carpenter or contractor. Measure And Track/Tape Up The Templates 1. - Page 13 STEP 4: Prepare The Wall & Upper Cabinet W A R N I N G To avoid risk of personal injury, electric shock or death: Note where electrical outlets and electrical wires are before you drill into the wall. Locate and disconnect power to any electrical circuits that could be affected by installing this oven.
-
Page 14: Step 5: Install The Mounting Plate
STEP 5: Install The Mounting Plate 3/16 Hole on Studs The Oven Must Be Connected To At Least One 5/8 Hole on Drywall Only Minimum 66 From the Floor Wall Stud. For Wall - Venting Only 1. Center the rear wall template in the space by lining up the plumb line on wall with centerline on template.Then securely tape or tack the rear wall template in place.Make sure the minimum width is 30 inches and that the top of the rear... -
Page 15: Step 6: Attach The Oven To The Wall
STEP 6: Attach The Oven To The Wall W A R N I N G To avoid risk of personal injury or property damage, you will need two people to install this microwave oven. NOTE: ● Do not apply force directly to the outside bottom surface of the product. The slide-out vent latch may be damaged if force is applied directly to the center bottom of the product.