LG LT65 Series Owner's Manual page 45

16. Colour Temperature (Command: x u)
► To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to 'Real data mapping'. See p.46.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. Energy Saving (Command: j q)
► To reduce the power consumption of the TV. You can also
adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Power Saving
Function
7 6 5 4
Low
0 0 0 0
Power
Low
0 0 0 0
Power
Low
0 0 0 0
Power
Low
0 0 0 0
Power
Low
0 0 0 0
Power
Low
0 0 0 0
Power
► 'Auto' is available in TV that supports 'Intelligent Sensor'.
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
18. Auto Configure(Command: j u)
► To adjust picture position and minimize image shaking auto-
matically. It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01: To set
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Level
Description
3 2 1 0
0 0 0 0 Off
0 0 0 1 Minimum
0 0 1 0 Medium
0 0 1 1 Maximum
0 1 0 1 Screen Off
0 1 0 0 Auto
EXTERNAL CONTROL DEVICE SETUP
19. Tune Command (Command: m a)
► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Data00 : High channel data
Data01 : Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don't care
(Only LT64**, LT65**, LT76**, LS64**)
Data02 : [Anttena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
Channel data range
Analog - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
(Only LT74**, LS34**)
Data02 : 0x00 : Analogue Main
0x10 : DTV Main
0x20 : Radio
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
(Except For Sweden, Finland, Norway, Denmark,
Ireland)
Digital - Min: 00 to Max: 270F (0 to 9999)
(Only Sweden, Finland, Norway, Denmark, Ireland)
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data Min: 00 to Max: 7DH
20. Programme Add/Skip(Command: m b)
► To set skip status for the current Programme.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip 01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
21. Key(Command: m c)
► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code - See p.39
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
45