How To Use The Appliance; First Time Use; Daily Use - Whirlpool FWDD1071681WS User Manual

User manual

HOW TO USE THE APPLIANCE

FIRST TIME USE

The first time the machine is switched on, you will be asked to
select the language and the display will automatically show
the language selection menu . To select the desired language
press the "Temperature" button
button . To confirm the selection press the "Spin"
To change the language switch off the machine and within
30 seconds press buttons "Key lock"
and "FreshCare+" simultaneously until an alarm is heard:
the language-selection menu will be displayed again .
To change the display luminosity, which by default is
set to the medium value, switch the machine off then
simultaneously press buttons "Key lock"
and "Rapid" until the buzzer sounds . Press buttons
"Temperature" and "Start delay"
40°
60°
desired level of luminosity then confirm by pressing "Spin"
button .

DAILY USE

PREPARING THE LAUNDRY
Empty pockets
• Coins, paper clips, etc . could damage the load and
the washing machine components .
• Tissues will break down during the wash cycle,
and the fragments will have to be subsequently
removed by hand .
Close all zippers, buttons, and hooks . Tie all
ribbons or belts
• Insert the smaller garments (e . g . nylon hosiery,
belts, etc . ) and garments with hooks (e . g . braziers)
into a fabric bag or a pillowcase with a zipper .
Remove any rings from curtains, or else place the
curtains inside a fabric bag together with the rings .
HOW TO USE THE WASHING MACHINE
1 . Load laundry
Open the door and load the laundry . Load the
articles one at a time loosely into the drum, without
overfilling . Observe the load sizes given in the
"PROGRAMME CHART" table . Overloading the machine will
result in unsatisfactory washing results and creased laundry .
2 . Close door
Make sure that no laundry gets stuck between
door glass and rubber seal . Close the door so
that you can hear it click shut .
3 . Open water tap
Make sure that the washing machine is connected to
the water mains . Open the water tap .
Switch on washing machine
Press the "ON/OFF" , the "Start/Pause"
slowly . The programme setting which you used last will
appear on the control panel .
4 . Set the desired programme
Select the required programme with the "Programme
selector" dial . The display will show the name
and duration of the cycle . The washing machine
automatically displays the maximum temperature and spin
speed settings possible for the selected programme . Adjust
the temperature and/or spin speed settings if needed with
the relative buttons .
or "Start delay"
40°
60°
button .
, "Intensive rinse"
, "Clean+"
. to choose the
lamp flashes
Remove any manufacturing debris:
• Select the "Cotton"
60°C .
• Pour a small quantity of detergent powder into the
main wash compartment of the detergent dispenser
(maximum 1/3 of the quantity the detergent manufacturer
recommends for lightly soiled laundry) .
Start the programme without adding any laundry (with
•
empty drum) .
• See section "DAILY USE" for more information on how to
select and start a programme .
Fabric type / Symbol on the wash label
• Cottons, mixed fibres, easy care/synthetics, wool,
handwash items .
• Colour
Separate coloured and white items . Wash new coloured
articles separately .
• Size
Wash items of different sizes in the same wash load, to
improve washing efficiency and distribution of the articles
in the drum .
• Delicates
Wash delicate items separately; they require gentle
treatment .
Change temperature, if needed
Press the "Temperature"
lower the temperature setting until cold wash has
been set ("- -" will be shown on the display) . Pressing
the button again sets the highest possible setting .
Change spin speed, if needed
Press the "Spin"
the spin speed until the spin cycle is turned off
("- -" shown on display) . Pressing the button again sets
the highest possible setting .
Select options, if needed
Press the button to select the option; the respective
square symbol on display illuminates
Press the button again to cancel the option; the
symbol extinguishes from the display
! If the selected option is incompatible with the programme
set, the incompatibility will be signalled by a buzzer (3 beeps)
and the wording "No Selection" will appear on the display .
! If the selected option is incompatible with another
previously set option, the wording "No Selection" will appear
on the display and the option will not be enabled.
programme at a temperature of
button to progressively
button to progressively decrease
.
.
EN
9