en Safety 1 Safety Observe the following safety instructions. 1.1 General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. 1.2 Intended use Only use this appliance: ¡...
Safety en 1.4 Safe installation Take note of the safety instructions when installing the appliance. WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate. ▶ Connect the appliance to a power supply with alternating cur- rent only via a properly installed socket with earthing.
Page 6
en Safety WARNING ‒ Risk of injury! The high weight of the appliance may result in injury when lifted. ▶ Do not lift the appliance on your own. If this appliance is not correctly installed in a washer-dryer stack, the installed appliance may fall. ▶...
Safety en ▶ Wear protective gloves when installing and transporting the ap- pliance. 1.5 Safe use WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. ▶ Never operate a damaged appliance. ▶ Never pull on the power cord to unplug the appliance. Always unplug the appliance at the mains.
Page 8
en Safety WARNING ‒ Risk of poisoning! Detergents and care products may result in poisoning if con- sumed. ▶ If accidentally swallowed, seek medical advice. ▶ Keep detergents and care products out of the reach of children. WARNING ‒ Risk of explosion! Laundry that has been pretreated with cleaning agents that con- tain solvents may cause an explosion in the appliance.
Safety en 1.6 Safe cleaning and maintenance Take note of the safety instructions when cleaning and performing maintenance work on the appliance. WARNING ‒ Risk of electric shock! Incorrect repairs are dangerous. ▶ Repairs to the appliance should only be carried out by trained specialist staff.
en Preventing material damage Make sure that the length of the ▶ 2 Preventing material thread on the connection to the water tap is at least 10 mm. damage If the water pressure is too high or too low, the appliance may not be Follow these instructions to avoid ma- able to operate properly.
Environmental protection and saving energy en Remove all detergent residue, Reduce the washing temperature for ▶ spray residue or other residues im- lightly and normally soiled laundry. mediately if they come into contact a At lower temperatures, the appli- with the appliance. ance consumes less energy.
en Installation and connection Replace the accessories in ques- ▶ 4 Installation and con- tion before operating the appli- ance. nection → "Accessories", Page 28 Note: The appliance has been tested 4.1 Unpacking the appliance at the factory to check it is in working order. As a result, water stains may ATTENTION! remain in the appliance.
Page 13
Installation and connection en ATTENTION! Installation loca- Requirements If residual water in the appliance tion freezes, this may cause damage to Kitchen unit Only install the the appliance. appliance under- Do not install or operate this appli- ▶ neath a continu- ance anywhere that is liable to ex- ous worktop that perience frost or outdoors.
Page 14
en Installation and connection Pull the hoses out of the holders. Remove the 4 sleeves. Unscrew and remove Put on the 4 cover caps. screws for the 4 transit bolts with a WAF 13 wrench. Press down on the 4 cover caps. Remove the power cable from the holder.
Installation and connection en 4.5 Connecting the appliance Siphon Secure the con- nection point with Connecting water inlet hoses a (24–40 mm) hose clamp. Connect the water inlet hose for hot water and cold water to the ap- pliance. Sink Fix and secure the water outlet hose with an el- → Page 28.
en Installation and connection To align the appliance, turn the ap- The connection details of the appli- pliance feet. Check that the appli- ance can be found under Tech- ance is level using a spirit level. nical data → Page 52. Check the mains plug is inserted properly.
Familiarising yourself with your appliance en 5 Familiarising yourself with your appliance 5.1 Appliance You can find an overview of the parts of your appliance here. On certain models, specific details such as the colour and shape may differ from those pictured. Maintenance flap for the drain Transit bolts → Page 13 pump → Page 36 Door...
en Familiarising yourself with your appliance 5.2 Detergent drawer Measuring aid for liquid deter- gent → "Inserting the measuring aid for liquid detergent", Page 30 Compartment II: ¡ Detergent for main wash ¡ Water softener ¡ Bleach ¡ Stain remover Compartment ¡ Fabric softener ¡...
first time en Pour standard washing powder first time 6 Before using for the into compartment II. first time Prepare the appliance for use. first time 6.1 Starting an empty wash- ing cycle Your appliance was inspected thor- oughly before leaving the factory. To remove any residual water, run the first wash cycle without any laundry.
en Display 7 Display The display shows the current settings, options or relevant information. Example: Display display Designation More information 0:40 Programme dura- Approximate expected programme dura- tion/programme tion or programme time remaining. time remaining 10h "Ready in" time → "Buttons", Page 23 9,0 kg Recommended The maximum load capacity for the selec- load...
Page 21
Display en display Designation More information Start/Pause Start, cancel or pause ¡ Lights up: The programme is running and can be cancelled or paused. ¡ Flashes: The programme can be star- ted or continued. Wash Programme status Rinse Programme status Spin Programme status – – – –...
Page 22
en Display display Designation More information E:35 / -10 Error Error code, error display, signal. Example...
Buttons en 8 Buttons The selection of programme settings depends on the programme that is set. Button Selection More information Έναρξη/ ¡ Start Start, cancel or pause the pro- Προσθήκη ρούχων gramme. ¡ Cancel (Start/Reload) ¡ Pause SpeedPerfect ¡ Activate Activate or deactivate a shorter pro- gramme duration.
en Programmes 9 Programmes Note: The laundry's care labels provide you with additional information on pro- gramme selection. Programme Description Max. load (kg) Βαμβακερά Wash hard-wearing items made from cotton, linen (Cottons) or blended fabrics. Also suitable as a short programme for normally soiled laundry when you activate SpeedPerfect.
Page 25
Programmes en Programme Description Max. load (kg) ¡ Max. 1400 rpm Μεταξωτά Wash delicate, washable items made from silk, vis- (Delicate/Silk) cose and synthetic fabrics. Use a detergent that is suitable for delicates or silk. Note: Wash especially delicate items or items with hooks, eyelets or clips in a mesh laundry bag.
Page 26
en Programmes Programme Description Max. load (kg) Πουκάμισα Wash non-iron shirts and blouses made from cot- (Shirts/Blouses) ton, linen, or synthetic or blended fabrics. Tip: In order to avoid creasing in your laundry, you can activate Λιγοτ. τσαλάκωμα. The laundry is only given a short spin and can be removed while still dripping wet.
Page 27
Programmes en Programme Description Max. load (kg) ¡ Max. 1200 rpm Καθαρισμός Cleaning and caring for the drum. – κάδου Use this programme in the following cases: (Drum Clean) ¡ Before using the appliance for the first time ¡ If you regularly wash at temperatures of 40 °C or lower ¡...
QR code in the table of Remove all items from any pock- ▶ contents or on www.bosch- ets in your laundry before using home.com. the appliance. To protect your appliance and the ▶...
¡ You can find further information in out automatically. the digital instruction manual by scanning the QR code in the table 13.2 Setting a programme of contents or on www.bosch- home.com. Turn the programme selector and ¡ Observe the information on safety set the required programme.
en operation Press down on the insert and re- 13.3 Adjusting the pro- move the detergent drawer. gramme settings Requirement: A programme has been set. → "Setting a programme", Page 29 Adjust the programme settings. ▶ → "Buttons", Page 23 Note: The programme settings are not saved permanently for the pro- gramme.
operation en Slide the measuring aid forwards. 13.8 Starting the programme Requirement: A programme has been set. → "Setting a programme", Page 29 Press Έναρξη/Προσθήκη ρούχων. ▶ a The drum rotates and load detec- tion takes place. This can take up to 2 minutes, after which water enters the drum.
en operation – If the water level is high, start 13.10 Soaking laundry the Στύψιμο programme or se- Note: No additional detergent is re- lect a suitable programme for quired. The washing solution is then draining. used for washing. → "Programmes", Page 24 Remove the laundry → Page 32. Start the programme.
Childproof lock en Wipe the rubber gasket dry and re- move any foreign objects. Leave the appliance door and de- tergent drawer open so that resid- ual water can evaporate. 14 Childproof lock Secure your appliance against being operated unintentionally using the controls.
en Basic settings 15 Basic settings You can configure the basic settings for your appliance to meet your needs. 15.1 Overview of the basic settings Basic setting Programme Value Description position End signal 0 (off) Set the volume of the signal at the 1 (quiet) end of the programme.
To keep your appliance working effi- ciently for a long time, it is important to clean and maintain it carefully. Note: You can find further information in the digital instruction manual by scanning the QR code in the table of contents or on www.bosch- home.com.
en Cleaning and servicing Pull out the insert upwards. Clean the opening for the deter- gent drawer. Clean the detergent drawer and in- sert with water and a brush, and Push in the detergent drawer. then dry them. 16.3 Cleaning the drain pump Clean the drain pump in the event of faults, e.g.
Page 37
Cleaning and servicing en Slide a sufficiently large container CAUTION - Risk of scalding! under the opening. When you wash at high temperat- ures, the detergent solution gets hot. Do not touch the hot detergent ▶ solution. To allow the detergent solution to flow out into the container, remove the sealing cap.
Page 38
en Cleaning and servicing Insert the pump cap. Cleaning the drain pump Ensure that the parts of the Requirement: The drain pump is ‒ pump cap are correctly as- empty. → Page 36 sembled. Since water may remain in the drain pump, unscrew the pump cap carefully.
Troubleshooting en 17 Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshoot- ing information before contacting after-sales service. This will avoid unneces- sary costs. WARNING Risk of electric shock! Incorrect repairs are dangerous. Repairs to the appliance should only be carried out by trained specialist ▶...
Page 40
en Troubleshooting Fault Cause and troubleshooting "E:36 / -10" Remove any unapproved extensions from the water ▶ hose. → "Connecting the appliance", Page 15 The pump cap is not fully screwed in. Ensure that the pump cap is screwed in all the way ▶...
Page 41
Troubleshooting en Fault Cause and troubleshooting Voltage under-usage Voltage under-usage may cause extension of a pro- symbol (double point). gramme. No remedial action possible. flashes. Voltage under-usage may cause extension of a pro- gramme. No remedial action possible. lights up. The temperature is too high. Wait until the temperature has dropped.
Page 42
en Troubleshooting Fault Cause and troubleshooting The appliance is not Check whether the lighting in your kitchen or other ▶ working. appliances are working. The programme does You have not pressed Έναρξη/Προσθήκη ρούχων. not start. Press Έναρξη/Προσθήκη ρούχων. ▶ Door is not closed. Close the door.
Page 43
Troubleshooting en Fault Cause and troubleshooting The water is not drain- Drain pump is blocked. ing. → "Cleaning the drain pump", Page 36 ▶ – – – – is activated. Continue the programme by selecting Στύψιμο or ▶ Άντληση and pressing Έναρξη/Προσθήκη ρούχων. → "Resuming the programme when the programme status is Rinse Hold", Page 32 The water outlet hose is connected too high.
Page 44
en Troubleshooting Fault Cause and troubleshooting The spin cycle runs The unbalanced load detection system eliminates an several times. imbalance by repeatedly redistributing the laundry. Not a fault – no action required. ▶ Note: When loading, where possible, place large and small items of laundry together in the drum. Different sized items of laundry distribute themselves better during the spin cycle.
Page 45
Troubleshooting en Fault Cause and troubleshooting Heavy foam build-up Detergent dosage is too high. Immediate measure: Mix one tablespoon of fabric ▶ softener with 0.5 litres of water and pour the mix- ture into the left-hand compartment (not for outdoor clothing, sportswear or items stuffed with down). Reduce the amount of detergent for the next wash- ▶...
Page 46
en Troubleshooting Fault Cause and troubleshooting Loud noises during Secure the appliance feet. ▶ the spin cycle. → "Aligning the appliance", Page 15 Transit bolts have not been removed. → "Removing the transit bolts", Page 13. ▶ Banging noises, rat- Foreign bodies have got into the drain pump. tling in the drain → "Cleaning the drain pump", Page 36 ▶...
Page 47
Troubleshooting en Fault Cause and troubleshooting The spin result is not Note: Where possible, mix large and small items in satisfactory. The laun- the drum. Different sized items of laundry distribute dry is too wet/too themselves better during the spin cycle. damp. Start the Στύψιμο programme.
Page 12 and Note: You can find further information → "Starting an empty washing in the digital instruction manual by cycle", Page 19. scanning the QR code in the table of contents or on www.bosch- home.com. Turn off the tap. Empty the water inlet hose.
Customer Service en 18.4 Disposing of old appli- 19 Customer Service ance If you have any queries on use, are Valuable raw materials can be re- unable to rectify faults on the appli- used by recycling. ance yourself or if your appliance needs to be repaired, contact Cus- WARNING tomer Service.
Page 50
en Customer Service Make a note of your appliance's de- tails and the Customer Service tele- phone number to find them again quickly.
Page 51
Consumption values for cold water en 20 Consumption values for cold water The following information is provided in accordance with the EU Ecodesign Regulation. The values given for programs other than the Eco 40-60 are indicat- ive only and were determined in accordance with the applicable standard EN60456.
en Technical data 20.1 Consumption values for hot water Measured values for appliances with hot water supply (inlet temperature of 55 °C) Programme Load Pro- Energy Water Max- Spin Resid- (kg) gramm con- con- imum speed e dura- sump- sump- temper- (rpm) mois- tion...
Technical data en Length of the wa- 150 cm ter outlet hose Length of the 160 cm power cord This product contains light sources from energy efficiency class F. These light sources are available as a spare part and must only be replaced by trained specialist staff.
Page 56
Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service direct- ory.