Table of Contents
Advertisement
Quick Links
Air Nail Coil Gun - CT4337
Operating Manual
NOTE: Please read and fully understand the instructions in this
manual before operating the pneumatic power tool. Carefully read
through this OPERATOR'S MANUAL to ensure efficient, safe
operation. It is recommended that the Manual be kept readily
available as an important reference when using this tool.
Advertisement
Table of Contents
Related Manuals for Neilsen CT4337
Summary of Contents for Neilsen CT4337
- Page 1 Air Nail Coil Gun - CT4337 Operating Manual NOTE: Please read and fully understand the instructions in this manual before operating the pneumatic power tool. Carefully read through this OPERATOR'S MANUAL to ensure efficient, safe operation. It is recommended that the Manual be kept readily...
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: AIR NAIL COIL GUN Model: CT4337 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN ISO 12100 :2010 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. - Page 3 IMPORTANT INFORMATION WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. When using the tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
- Page 4 WARNING: The operating instructions shall draw attention to the following a) Only those fasteners listed in the operating instructions may be used in the fastener driving tools; NOTE: The fastener driving tool and the fasteners listed in the operating instructions must be seen as one unit system in terms of technical safety.
-
Page 5: Safety Information
SAFETY INFORMATION WARNING: BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND THE FOLLOWING SAFETY INSTRUCTIONS.FAILURE TO FOLLOW WARNING COULD RESULT IN DEATH OR SERIOUS INJURY. 1. WEAR SAFETY GLASSES OR GOGGLES. Danger to the eyes always exists due to the possibility of dust being blown up by the exhausted air or of a fastener flying up due to the improper handling of the tool. - Page 6 6. DO NOT USE A WRONG FITTING. The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the line of air is disconnected, possibly causing injury.
- Page 7 14. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE AND CORNER OF THE WORK AND THIN MATERIAL The work piece is likely to split and the fastener could fly and hit someone. 15. DO NOT DRIVE FASTENERS ON THE TOP OF OTHER FASTENERS. Driving fasteners of the top of other fasteners may cause deflection fasteners which could cause injury.
-
Page 8: Technical Data
TECHNICAL DATA Type of tool CN45 Construction Coil Nailer 11-1/8”X4-1/4”X10-1/8” Dimensions 248mmX108mmX260mm Weight (without fasteners) 1.60kgs (3.50lbs.) Actuation mode Contact/Single-sequential actuation 400 nails (conical wire welded nails) Magazine capacity 200 nails (plastic sheet collated nails) Maximum allowable pressure 120psi (8.3bar) Recommended pressure range 70psi to 100psi (5bar to 7bar) Fasteners... - Page 9 NAILER CONNECTION AND OPERATION NOTE: The information contained in this manual is designed to assist you in the safe operation of the nailer. Some illustrations in this Manual may show details or attachments that are different from those on your nailer. Air Supply, Connections and Operating Pressure Read section titled SAFETY.
- Page 10 Nailer Connection and Operation Lubricator • The lubricator supplies and oil mist to the nailer. • Inspect the lubricator before operation to be sure the supply of lubricant is adequate. • If an inline lubricator is not used, a few drops of oil will need to be added to the nailer inlet before each use.
-
Page 11: Instruction For Operation
INSTRUCTION FOR OPERATION 1. Before operation (1) Wear safety glasses or goggles (2) Do not connect the air supply (3) Inspect screw tightness (4) Check operation of the contact arm & trigger if moving smoothly (5) Connect the air supply (6) Check the air-leakage.(the tool must not have the air-leakage.) (7) Hold the tool with finger-off the trigger, then push the contact arm against the work- pieces.(the tool must not operate.) -
Page 12: Maintenance And Inspection
MAINTENANCE AND INSPECTION Read the section title SAFETY. SERVICE AND REPAIRES All quality tools will eventually require servicing or replacement of parts due to wear from normal use. It is recommended that these operations should be performed by a professional technician. -
Page 13: Parts List
PARTS LIST CODE Description CODE Description 610560 BOLT M6X20 (Loctite) 320110 TRIGGER STEM 321600 BUSHING 510030 O-RING 2.5X1.4 410490 EXHAUST COVER 620050 TRIGGER VALVE SPRING 321590 EXHAUST FILTER (A) 510240 O-RING 8.6X1.9 321580 EXHAUST FILTER (B) 330010 TRIGGER VALVE BUSHING 610120 BOLT M5X25 510180... - Page 14 TOOL SCHEMATIC-CN45...
- Page 16 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...