Summary of Contents for Corinex High Performance Repeater I
- Page 1 Corinex Installation Guide Corinex High Performance Repeater I & II CXP-UFSGW-I CXP-UFSGW-II Version 2.0 | May, 2022...
- Page 2 COPYRIGHT The content of this document is furnished for informational use only, it is subject to change without notice, and it does not represent a commitment on the part of Corinex Communica- tions Corp. Corinex Communications Corp. assumes no responsibility or liability for any errors or inac- curacies that may appear in this document.
-
Page 3: Table Of Contents
Status LEDs ......................5 Connectors ......................7 Software and Initial Setup ................8 Commissioning ..................8 Installation ......................8 Powering up the device ..................8 Voltage sensing feature..................11 BPL Coupling ..................... 12 Corinex High Performance Repeater I & II CXP-UFSGW-I | CXP-UFSGW-II... - Page 4 Figure 7: QUICKON connector - step 3 ................. 9 Figure 8: QUICKON connector - step 4 ...............10 Figure 9: QUICKON connector - step 5 ...............10 Figure 10: Making connector connection ..............10 Figure 11: Mating connector lock ................11 Corinex High Performance Repeater I & II CXP-UFSGW-I | CXP-UFSGW-II...
-
Page 5: General Information
This document is a general description and installation guide for the following device: • Corinex High Performance Repeater (CXP-UFSGW) Included in the delivery of the CXP-UFSGW • Corinex High Performance Repeater I (CXP-UFSGW-I) Hardware Installation CXP-UFSGW has the option to mount using screws or cable ties. -
Page 6: 2.1.1 Mount Using Screw
Holes are provided on two sides of the gateway for passing the cable tie. Figure 2 shows how to mount the gateway using cable ties. Figure 2: Mounting using cable ties Corinex High Performance Repeater I & II Return to Table of Contents CXP-UFSGW-I | CXP-UFSGW-II... -
Page 7: Status Leds
ON and wait- autoconf is ing for config- finished, or AC uration to be power is ON completed. and device is using NVRAM settings. Corinex High Performance Repeater I & II Return to Table of Contents CXP-UFSGW-I | CXP-UFSGW-II... - Page 8 IPv6 successful, if link-local ad- it syncs with dress ready. Secure Link LED. Secure Link Function: Secure link indication Different statuses are given below: Corinex High Performance Repeater I & II Return to Table of Contents CXP-UFSGW-I | CXP-UFSGW-II...
-
Page 9: Connectors
Ethernet device for backhauling through BPL com- munication channel. Figure 4: front panel of a) CXP-UFSGW-I and b) CXP-UFSGW-II Corinex High Performance Repeater I & II Return to Table of Contents CXP-UFSGW-I | CXP-UFSGW-II... -
Page 10: Software And Initial Setup
Alternatively, CXP-UFSGW can be set to use static configuration and this device can be set to function as a BPL headend or as a BPL time division repeater. Corinex Smart Grid Config Tool (SCT) can also be used to configure the device. Refer to the SCT manual for further details. -
Page 11: Figure 5: Quickon Connector - Step 1
Figure 6: QUICKON connector - step 2 Step 3: Cut the stranded wire ends so they are flush. Figure 7: QUICKON connector - step 3 Corinex High Performance Repeater I & II Return to Table of Contents CXP-UFSGW-I | CXP-UFSGW-II... -
Page 12: Figure 8: Quickon Connector - Step 4
Look for the ‘arrow’ mark on the cable, which indicates where it should be inserted. See the figure 10 below: Figure 10: Making connector connection Corinex High Performance Repeater I & II Return to Table of Contents CXP-UFSGW-I | CXP-UFSGW-II... -
Page 13: Voltage Sensing Feature
CXP-UFSGW uses an SNMP trap feature to notify the headend system (example of headend system: Corinex Compact BPL Proxy Headend) if there is any voltage alert or imbalance be- tween different phase voltages. The voltage thresholds are remotely configurable using SNMP Corinex High Performance Repeater I &... -
Page 14: Bpl Coupling
Note that L2 and L4 are used for AC power input as well. So, if the CXP-UFSGW is installed within a single-phase network, make sure to use the pins L2 and L4 for powering up the de- vice. Corinex High Performance Repeater I & II Return to Table of Contents CXP-UFSGW-I | CXP-UFSGW-II...