PALLADIOM LBMRJ-C Installation & Setup Manual

Wire-Free Roller Shade, Models LBMRJ-C, LBMRK-C
Chassis Installation & Setup Guide
! WARNING: Important safety instructions
For safe installation and operation of this product, follow and save these important
safety instructions.
• This device is not intended for use by persons
(including children) with reduced physical, sensory,
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the device by a
person responsible for their safety. Children must
be supervised to ensure that they do not play with
the device.
• DO NOT allow children to play with device controls.
Keep remote controls away from children.
• Frequently examine the installation for imbalance
and signs of wear or damage to cables, springs,
and fixings. DO NOT operate the device if repair or
adjustment is necessary.
• This device is powered by D size, alkaline batteries
only; DO NOT mix battery types.
• Install new batteries only; DO NOT mix new and
used batteries.
• DO NOT install damaged or modified batteries.
Important Installation Notes:
A. Plan the installation to maintain sufficient clearance between the shade and any other object, including
window or door trim, ceilings, corners, hardware, cranks, lock levers, other shades, and drapery.
B. This product is not suitable for mounting in a pocket or recess.
C. This product is battery powered and requires specific installation clearances to allow battery changes
without demounting.
Please refer to the Product Specification Submittal, PN 085708, and Application Note #802 (both
available for download at Lutron.com) for detailed installation limitations and restrictions.
D. For safety, shades over 48 in (1219 mm) must be installed by two people.
E. The shade system must be mounted to blocking or other suitable structural material. It is the
responsibility of the installer to choose and install fasteners that are appropriate for the mounting surface
such that each shade bracket can support 400 lbs (181.4 kg).
1.1
MEASURE AND MARK FOR A SINGLE SHADE:
A. Outside Mount – Wall, Ceiling, or Door
1. Measure across the window at the top, and make a mark at the
half-way point.
2. Note the correct bracket-to-bracket width (BtoB), on the shade box label.
3. Measuring from the window center to the left, mark a distance equal to:
BtoB / 2.
4. Repeat the process, measuring from the window center to the right, to
mark the opposite bracket location.
5. Measure from mark to mark, verifying the distance is equal to BtoB,
±1/8 in (3 mm).
1.2 MEASURE AND MARK FOR GANGED SHADES (3-shade example):
1. Measure across the window at the top, and make a mark at the half-way point
(Window Center).
2. Note the correct bracket-to-bracket width (BtoB), on each shade box label, then add
the widths together to get the Total System Width (TSW).
3. Measuring from the window center on a level line to the left, mark a distance equal to:
TSW / 2.
4. Measuring from the mark made in Step 3 on a level line to the right, mark a distance
equal to Shade 1 BtoB.
5. Measuring from the mark made in Step 4 on a level line to the right, mark a distance
equal to Shade 2 BtoB.
6. Measure from end-mark to end-mark, verifying the distance is equal to the TSW,
calculated at Step 2.
2
MOUNT THE SHADE BRACKETS:
NOTE: The mounting holes in all brackets are elongated to allow for adjustment. Confirm that brackets are level and aligned (add shims if necessary), and verify the correct bracket-to-bracket width before tightening the mounting screws.
A. Mount the Idler Bracket
Align the idler bracket with the bracket location mark(s) at the idler side of the window, and mark the mounting hole
locations. Pre-drill pilot holes if appropriate, and fasten the bracket using the mounting screws provided or other fasteners
appropriate for the mounting surface.
End Bracket Center Bracket
BtoB Mark
BtoB Mark
Socket
Plate
ceiling mount shown ceiling mount shown
Align the outside edge Align the center of the Remove the socket plate screw and separate the socket plate from the
of the bracket on the bracket foot on the mounting plate, then align on the marks and secure with 2 screws.
BtoB mark and secure BtoB mark and secure
Reinstall the socket plate and secure it with the socket plate screw.
with 2 screws with 4 screws
04/2022
P/N 045913 Rev. A
please read before installing
• DO NOT install rechargeable batteries.
• Remove depleted batteries promptly and dispose
of them responsibly in accordance with local laws
and policies. Recycle if possible.
• Wear hand and face protection when removing
batteries found to be leaking, and dispose of leaking
batteries responsibly in accordance with local laws
and policies.
• Remove all batteries from the device:
— when maintenance is being performed in the vicinity.
— when the device will be unused or stored for an
extended period of time.
• DO NOT expose the device or its batteries to
extreme temperature.
• Metal objects in the area of the batteries and battery
terminals may cause a short circuit and device failure;
keep foreign objects away from the batteries and
battery compartment.
• This product is rated for 10 operation cycles.
B. Inside Mount – Ceiling
1. Note the correct bracket-to-
bracket width (BtoB), on the
shade box label.
2. Measure from jamb to jamb at
the top of the window opening,
verifying the distance is equal to BtoB, ± 1⁄8 in (3 mm).
3. Measuring from the front edge of the window opening toward the window glass, mark the
mounting surface at the desired bracket mounting depth.
C. Inside Mount – Jamb
1. Note the correct bracket-to-
bracket width (BtoB), on the shade
box label.
2. Measure from jamb to jamb at the
top of the window opening, verifying the distance is equal to BtoB, ± 1⁄8 in (3 mm).
3. Measuring down from the top of the window opening, mark each jamb at the desired bracket
mounting height.*
4. Measuring from the front edge of the jamb toward the window glass, mark each jamb at the
desired bracket mounting depth.*
Shade 1 BtoB
Shade 1
Shade 1
left bracket
! CAUTION: RISK OF FALLING OBJECTS. Read and follow all instructions for mounting the shade system. Failure to follow these instructions could result in minor to moderate injury.
Jamb Bracket
Height Mark
Mounting
Depth
Plate Mark
Window Room
Worldwide Headquarters | USA
Lutron Electronics Co., Inc.
7200 Suter Road, Coopersburg, PA 18036-1299 USA
Customer Assistance: 1.844.LUTRON1 (588-7661)
lutron.com/help | support@lutron.com
COMPONENTS:
PALLADIOM Wire-Free Roller Shade
10 Operation Cycles Rated
Bracket Kit
(1) Left Bracket & (1) Right Bracket* , according to configuration ordered
each bracket includes one 1 shim; wall and ceiling brackets include foot cover(s)
Wall Ceiling / Door
Operator Idler Center * Operator
Operator Bracket Wall / Ceiling / Door
Slide Ring Bracket Foot Covers
Wall Ceiling / Jamb Quantity and type varies
Door with included brackets
TOOLS NEEDED:
#2 Phillips Driver Bit
1/8 in (#31) Drill Bit
(correct pilot hole size for the
included mounting screws)
Power Drill / Driver Magnetic #1 Phillips Screwdriver
*
Window Center
Total System Width / 2
Shade 2 BtoB
Shade 2
Shade 1 Shade 2 Shade 2
right bracket left bracket right bracket
(center bracket; (center bracket;
packaged with Shade 2) packaged with Shade 3)
B. Mount the Operator Bracket
Align the operator bracket with the bracket location mark(s) at the operator side of the window, and mark the mounting hole locations. Pre-drill pilot
holes if appropriate, and fasten the bracket using the mounting screws provided or other fasteners appropriate for the mounting surface.
End Bracket
BtoB Mark
BtoB Mark
BtoB
Mark
wall mount
door mount
Align the outside edge of the bracket on the
BtoB mark and secure with 4 screws
EEA | Netherlands United Kingdom
Lutron NL B.V. Lutron EA Ltd
Herengracht 466 125 Finsbury Pavement, 4th floor, London EC2A 1NQ, UK
1017 CA Netherlands TEL: +44.(0)20.7702.0657 | FAX: +44.(0)20.7480.6899
(Importer) Technical Support: +44.(0)20.7680.4481 | FREEPHONE: 0800.282.107
Models:
Shade
LBMRJ-C
LBMRK-C
Jamb
FCC ID: JPZ0137
FCC / IC INFORMATION
This device complies with part 15 of the FCC Rules and Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
Idler Center * Operator Idler
undesired operation.
Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's
authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
* IMPORTANT: A shade ordered digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
with a center bracket specified
generates, uses and can radiate radio frequency energy and, if not installed and used in
on the right side (for ganged
accordance with the instructions, may cause harmful interference to radio communications.
installation) will include only
However, there is no guarantee that interference will not occur in a particular installation.
the bracket specified for the
If this equipment does cause harmful interference to radio or television reception, which
left side. The center bracket
can be determined by turning the equipment off and on, the user is encouraged to try to
will be included as the left correct the interference by one or more of the following measures:
bracket for the next shade - Reorient or relocate the receiving antenna
Mounting - Increase the separation between the equipment and receiver
(to the right) in the ganged
Screws - Connect the equipment into an outlet on a circuit different from that to which the receiver
installation. Refer to section
is connected
quantity varies 1.2 for additional information.
- Consult the dealer or an experienced radio/TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Tape Measure
Pencil
Level or Laser Level
Important Inside-Mount Clearance Information
ROLLUP RADIUS (RR): Measure the fabric roll diameter (Rollup Diameter; also listed on
the original shade quote). RR = Rollup Diameter / 2.
JAMB BRACKET MOUNTING HEIGHT: To ensure adequate fabric roll clearance, jamb
brackets must be mounted at a distance from the top of the jamb equal to or greater than
the Rollup Radius (RR) minus 1/2 in (13 mm).
MOUNTING DEPTH: To allow
free access to the battery
compartment, the mounting 5/8 in
(16 mm)
Ceiling
depth must be 5/8 in (16 mm)
max.
Bracket
or less.
Jamb
Brackets may be mounted
deeper than 5/8 in (16 mm), **
but battery access will require
Window Room
full removal of the shade from
the brackets.
** BOTTOM BAR CLEARANCE: To ensure adequate clearance for the PALLADIOM
bottom bar, the distance from the rear of the bracket to the window must be equal to or
greater than the Rollup Radius (RR) minus 1-1/8 in (29 mm).
For all other bottom bar types (Architectural, Designer, Sealed), the distance from the
rear of the bracket to the window must be equal to or greater than the Rollup Radius
(RR) minus 1-5/8 in (41 mm).
1. Shade BtoB is measured to/from the centerline of
Shade 3 BtoB
2. Individual shade BtoB tolerance is ± 1⁄8 in (3 mm)
3. Inside mount shown - measure-and-mark
Shade 3
4. All inside mounting depth, height, and clearance
Shade 3 Shade 3
left bracket right bracket
5. Wall-mount center brackets are operator-side
Center Bracket
BtoB Mark
BtoB Mark
BtoB
Mark
wall mount
ceiling
door mount
mount
Align the center of the bracket on the BtoB
mark and secure with 4 screws
The Lutron logo and Palladiom are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries
Duracell is a registered trademark of Duracell U.S. Operations, Inc., RAYOVAC is a registered trademark of Spectrum Brands, Inc.
Electronic Drive Unit (EDU)
QSFC-EDU-BP-C
4.5 – 9.0 V-
QSSC-EDU-PLDM-C
QSFCJ-EDU-6D-RPL 9.0 V- 5 W 6 in-lb (0,68 N•m)
QSFCJ-EDU-4D-RPL 6.0 V-
QSFCJ-EDU-3D-RPL 4.5 V-
QSSC-EDU-PLDM-C 4.5 – 9.0 V-
QSFCK-EDU-6D-RPL 9.0 V-
5 W 6 in-lb (0,68 N•m)
QSFCK-EDU-4D-RPL 6.0 V-
QSFCK-EDU-3D-RPL 4.5 V-
IC: 2851A-JPZ0137 HVIN: RFB-A
D-Cell Alkaline Batteries
(3, 4, or 6 depending on shade size;
available separately)
Lutron recommends
Duracell or RAYOVAC
® ®
Mounting Height
RR – 1/2 in (13 mm)
min.
Jamb
Bracket
Mounting Depth
5/8 in (16 mm) max.
Jamb
**
Window Room
PALLADIOM Designer
Architectural
Sealed
full-wrap & half-wrap
Ganged Shades Example:
center brackets
procedure is the same for outside mount
information presented in section 1.1 above is
applicable to inside-mounted ganged shades
reversible - ceiling mount center brackets are not
Jamb Bracket
Height Mark
Depth
Mark
Room Window
ceiling
mount
Align the Jamb Bracket
on the marks and secure
with 2 screws.
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.