Cateye STRADA CADENCE CC-RD200 User Manual

CATEYE STRADA CADENCE
CYCLOCOMPUTER CC-RD200
Before using the computer, please thoroughly read this manual and keep it for
future reference.
WARNING / CAUTION
• Do not concentrate on the computer while riding. Ride safely!
• Install the magnet, sensor, and bracket securely. Check these periodically.
• If a child swallows a battery, consult a doctor immediately.
• Avoid having the computer in direct sunlight for unnecessary or extended periods.
• Do not disassemble the computer.
• Do not drop the computer. Doing so may result in a computer malfunction or damage.
• When using the computer installed on the bracket, change the MODE by pressing on the three dots
below the screen. Pressing hard on other areas can result in malfunction or damage to the computer.
• Never place the computer on a metal surface. If you do, the contact points will conduct
electricity, discharging the battery.
• Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket
threads.
• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.
• Dispose of used batteries according to local regulations.
• LCD screen may be distorted when viewed through polarized sunglass lenses.
Preparing the computer
AC
Battery case cover
MENU
Contact
MODE
: Speed unit
: Wheel size icon
1
Clear all data (initialization)
Press the AC button on the back.
2
Select the desired speed units
Select " " or " ".
km/h ↔ mph
Register
the setting
MENU MENU
MODE MODE
3
Enter the tire circumference
Enter the tire circumference of your bicycle in
mm.
* Refer to the tire circumference reference table.
Move digits
Increase
(by pressing
MENU MENU
& holding)
MODE MODE
MODE MODE
4
Set the clock
When MODE is pressed and held, "Displayed time",
"Hour", and "Minute" will appear, in this order.
24h ↔
Switch the
12h, or
screen or
increase
move digits
MODE MODE
MODE MODE
the value
(by pressing
& holding)
Tire circumference
reference table
Tire size
When the computer is
12 x 1.75
mounted on the bracket
14 x 1.50
14 x 1.75
Push! 16 x 1.50
16 x 1.75
18 x 1.50
18 x 1.75
20 x 1.75
20 x 1-3/8
22 x 1-3/8
22 x 1-1/2
24 x 1
24 x 3/4 Tubular
24 x 1-1/8
24 x 1-1/4
24 x 1.75
24 x 2.00
24 x 2.125
26 x 7/8
26 x 1 ( 59 )
AC
26 x 1 ( 65 )
26 x 1.25
26 x 1-1/8
26 x 1-3/8
26 x 1-1/2
26 x 1.40
26 x 1.50
26 x 1.75
26 x 1.95
26 x 2.00
26 x 2.10
26 x 2.125
26 x 2.35
26 x 3.00
27 x 1
27 x 1-1/8
27 x 1-1/4
27 x 1-3/8
650 x 20C
650 x 23C
650 x 35A
Register
650 x 38A
650 x 38B
the
700 x 18C
setting
700 x 19C
700 x 20C
700 x 23C
700 x 25C
700 x 28C
700 x 30C
700 x 32C
700C Tubular
Register
700 x 35C
the setting 700 x 38C
700 x 40C
MENU MENU
(finish)
29 x 2.1
29 x 2.3
Measure wheel circumference (L) of your bike
To get the most accurate calibration do a wheel roll
out. With the valve stem perpendicular to the
ground, mark the pavement at the valve stem. With
the riders weight on the bike, roll the wheel one tire
revolution in a straight line and mark the ground
when the valve stem is perpendicular to the ground
again. Measure the distance in millimeters. This is
the most accurate wheel calibration number.
How to install the unit on your bicycle
2 7
1
8
3
5
4
6
9
Install the sensor and magnet :
The magnet should pass
A
through the sensor line.
Magnet
L (mm)
935
Sensor line
1020
1055
1185
1195
1340
1350
1
1515
Install the speed sensor and wheel magnet
1615
1770
9
1785
3
1753
1785
1795
1905
1890
1925
1965
1920
Left Chain Stay (Inside)
1913
1952
2
Install the cadence sensor and cadence magnet
1953
1970
2068
2100
9 4
2005
2010
2023
2050
2055
2068
2070
2083
Left Chain Stay (Outside)
2170
2145
3
2155 Route the cable
2161
Use the nylon tie 9 to secure
2169
1938
the cable on the frame. Wind
1944
the cable on the rear brake
2090
cable as shown.
2125
2105
2070
2080
Caution:
2086
Turn the handlebar to make
2096
2105
sure wire does not hinder full
2136
rotation.
2146
2155
2130
2168
4
Attach the bracket to the stem or handlebar
2180
2200
When attaching the bracket to the stem
2288
2326
2
1
When attaching the bracket to the handlebar
L mm
1
2
5
Remove/install the
computer
Click
* After installation, check that the speed sensor and cadence sensor are functioning properly.
In the case of the speed sensor, lift the rear wheel off the ground and spin the wheel to
check the speed is displayed.
In the case of the cadence sensor, press MODE to display C (cadence) on the mode screen.
Rotate the crank in the non driving direction and check cadence is displayed.
If the speed is not displayed, check that conditions
U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending
Copyright© 2007 CATEYE Co., Ltd.
CCRD20-070727 066600520 4
1
Bracket band
2 Bracket
3 Speed sensor
4 Cadence sensor
5 Wheel magnet
6 Cadence magnet
7 Sensor rubber pad
8
Bracket rubber pad
9
Nylon ties (x10)
The clearance between the sensor surface
B
and the magnet must not exceed 3 mm.
* When installing cadence sensor 4, insert
Sensor
the sensor rubber pad 7 if necessary.
Pull
securely
Pull
securely
Toward the sensor line
8
Caution:
Tighten the bracket, ensuring that the
cable does not get caught in the stem.
Handlebar
8
Caution:
Tighten the bracket, ensuring that the cable
does not get caught in the handlebar.
While supporting it
by hand,
Caution:
Round off the cut edge of the
push it out as if lifting
bracket band to prevent injury.
the front up
and are satisfied.
A B
ENG
Sensor
Magnet
Rear wheel spoke
5
Toward the sensor line
Left crank (Inside)
9
6
Pull securely
9
5 5
6
4 4 3 3
Stem
Cut