Using The Lock Menu - Toshiba 20A45C Owner's Manual

USING THE LOCK MENU

The LOCK menu includes the CH LOCK, VIDEO LOCK, GAMETIMER and CHANGE PASSWORD functions.
You can use these functions after entering the correct PASSWORD.
TO REGISTER PASSWORD
1 Press MENU and then SET + or – until the indicator next
to "LOCK" begins to flash, then press ENTER.
2
Enter your password (4 digits) using the Direct channel
selection buttons (0–9).
In the event of entering an incorrect password press
RESET. Then press ENTER.
3
Enter the password again, and then press ENTER.
The password is now registered and the LOCK menu
appears.
LOCKING CHANNELS
With the CH LOCK feature, you can lock specific channels. You will not be able to tune locked channels unless you clear the setting.
You can choose to lock up to nine TV channels and nine cable channels.
1
Use the Channel Number buttons (0–9) to display the
television channel you wish to lock.
2
Press MENU, then press SET + or – until the indicator
next to "LOCK" begins to flash. Then press ENTER.
Use the Channel Number buttons (0–9) to enter your
3
password, then press ENTER.
The LOCK menu appears.
Press SET + or – until the indicator next
4
to "CH LOCK" begins to flash, then
press ENTER.
Press SET + or – to select:
5
• INPUT to select the channel as one to
be locked. Then press ENTER.
• ALL CLEAR to clear all channels from
the list of locked channels. Then press
ENTER.
LOCKING VIDEO INPUT
With the VIDEO LOCK feature, you can lock out the input
source (VIDEO) and channels 3 and 4. You will not be able to
select the input sources with the TV/VIDEO button or Channel
buttons unless you clear the setting.
Press MENU, then press SET + or – until the indicator
1
next to "LOCK" begins to flash, then press ENTER.
Use the Channel Number buttons (0–9) to enter your
2
password, then press ENTER. The LOCK menu appears.
Press SET + or – until the indicator
3
next to "VIDEO LOCK" begins to flash,
then press ENTER.
4
Press SET + or – to select:
• OFF: Unlocks all video input sources.
• VIDEO: Locks VIDEO.
• VIDEO +: Locks VIDEO, channel 3 and channel 4.
This option should be used if you use the antenna
to play a video tape.
5 Press MENU repeatedly until the menu screen is cleared.
NOTE:
After programming VIDEO LOCK, change channels or press the
TV/VIDEO key before turning off the television.
J3M91421A(E)_P08-12
LOCK
CH LOCK
VIDEO LOCK
GAME TIMER
CHANGE PASSWORD
〈 + / – / ENTER / MENU 〉
CH LOCK
CABLE
INPUT
--- --- ---
--- --- ---
--- --- ---
ALL CLEAR
〈 + / – / ENTER / MENU 〉
VIDEO LOCK
OFF
VIDEO
VIDEO+
〈 + / – / ENTER / MENU 〉
11
NOTES:
• If you want to change your password, follow steps 1 and 2 and
select "CHANGE PASSWORD" option. Then enter your new
password.
• If you forget or lose your password, you can reset it using the
following procedure:
- While holding down the VOLUME 4 button on the TV, press
"0" on the remote control for a few seconds.
6 Repeat steps 1 through 5 to lock other channels. When you
are finished locking channels, press MENU repeatedly until
the menu screen is cleared.
If you try to tune a locked channel, the TV will not display it, but
will display the nearest unlocked channel.
NOTES:
• If you are accessing the LOCK menus for the first time,
choose a four-digit number to be your password.
• After programming CH LOCK, change channels before
turning off the television.
• If you want to unlock channels, select ALL CLEAR in step 5,
then press ENTER.
SETTING THE GameTimer™
With the GameTimer™ feature, you can automatically activate
the VIDEO LOCK feature (VIDEO setting) to set a time limit for
playing a TV game (30, 60, 90, or 120 minutes).
1 Press MENU, then press SET + or – until the indicator next to
"LOCK" begins to flash, then press ENTER.
Use the Channel Number buttons (0–9) to enter your pass-
2
word, then press ENTER. The LOCK menu appears.
3 Press SET + or – until the indicator next
to "GAMETIMER" begins to flash, then
press ENTER.
Press SET + or – to select a time limit
4
(30 minutes, 60 minutes, 90 minutes,
120 minutes or OFF).
Press MENU repeatedly until the menu screen is cleared.
5
After the GameTimer is programmed, the display will
appear briefly every ten minutes to remind you that the
GameTimer is operating. When the programmed end time
is reached, the display will change the channel
automatically.
NOTE:
When the programmed end time is reached, the TV will change
channels automatically and the VIDEO LOCK feature will be
activated. To turn off the VIDEO LOCK, see "LOCKING VIDEO
INPUT," at left.
11/03/2005, 3:34 PM
〈 〉
11