Cateye STRADA CC-RD100N User Manual

CATEYE STRADA
CYCLOCOMPUTER CC-RD100N
Before using the computer, please thoroughly read this manual and keep it for
future reference.
WARNING / CAUTION
• Do not concentrate on the computer while riding. Ride safely!
• Install the magnet, sensor, and bracket securely. Check these periodically.
• If a child swallows a battery, consult a doctor immediately.
• Do not leave the computer in direct sunlight for unnecessary or extended periods.
• Do not disassemble the computer.
• Do not drop the computer. Doing so may result in a computer malfunction or damage.
• When using the computer installed on the bracket, change the MODE by pressing on the
three dots below the screen. Pressing hard on other areas can result in malfunction or
damage to the computer.
• Never place the computer on a metal surface. If you do, the contact points will conduct
electricity, discharging the battery.
• Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the
bracket threads.
• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or
alcohol.
• Dispose of used batteries according to local regulations.
• LCD screen may be distorted when viewed through polarized sunglass lenses.
Preparing the computer
AC
Battery case cover
MENU
Contact
MODE
: Speed unit
: Wheel size icon
1
Clear all data (initialization)
Press the AC button on the back.
2
Select the desired speed units
Select " " or " ".
km/h ↔ mph
Register the
setting
MENU MENU
MODE MODE
3
Enter the tire circumference
Enter the tire circumference of your bicycle in
mm.
* Refer to the tire circumference reference table.
Move digits
Increase
(by pressing
& holding)
MENU MENU
MODE MODE
MODE MODE
4
Set the clock
When MODE is pressed and held, "Displayed
time", "Hour", and "Minute" will appear, in
this order.
Switch the
24h ↔ 12h,
screen or
or increase
move digits
the value
MENU MENU
MODE MODE
(by pressing
MODE MODE
& holding)
Tire circumference
reference table
Tire size
When the computer is
12 x 1.75
mounted on the bracket
14 x 1.50
14 x 1.75
Push!
16 x 1.50
16 x 1.75
18 x 1.50
18 x 1.75
20 x 1.75
20 x 1-3/8
22 x 1-3/8
22 x 1-1/2
24 x 1
24 x 3/4 Tubular
24 x 1-1/8
24 x 1-1/4
24 x 1.75
24 x 2.00
24 x 2.125
26 x 7/8
26 x 1 ( 59 )
AC
26 x 1 ( 65 )
26 x 1.25
26 x 1-1/8
26 x 1-3/8
26 x 1-1/2
26 x 1.40
26 x 1.50
26 x 1.75
26 x 1.95
26 x 2.00
26 x 2.10
26 x 2.125
26 x 2.35
26 x 3.00
27 x 1
27 x 1-1/8
27 x 1-1/4
27 x 1-3/8
650 x 20C
650 x 23C
650 x 35A
650 x 38A
650 x 38B
Register
700 x 18C
the setting
700 x 19C
700 x 20C
700 x 23C
700 x 25C
700 x 28C
700 x 30C
700 x 32C
700C Tubular
700 x 35C
700 x 38C
700 x 40C
29 x 2.1
Register
29 x 2.3
the
Measure wheel
setting
circumference (L) of
your bike
(finish)
To get the most accurate
calibration do a wheel roll
out. With the valve stem
perpendicular to the ground,
mark the pavement at the
valve stem. With the riders
weight on the bike, roll the
wheel one tire revolution in a
straight line and mark the
ground when the valve stem
i s p e r p e n d i c u l a r t o t h e
ground again. Measure the
distance in millimeters. This
is the most accurate wheel
calibration number.
How to install the unit on your bicycle
2 5
1
3
4
0
9
1
Attach the bracket to the stem or handlebar
When attaching the bracket to the stem
2
1
Caution:
Tighten the bracket, ensuring that the cable does
L (mm)
not get caught in the stem.
935
When attaching the bracket to the handlebar
1020
1055
1185
1195
2
1
1340
1350
1515
1615
1770
1785
1753 Caution:
1785
Tighten the bracket, ensuring that the cable does not get caught in the handlebar.
1795
1905
2
Wrap the cable around
1890
1925
the front brake cable
1965
1920
1913
Caution:
1952
Turn the handlebar to
1953
1970 make sure wire does
2068
not hinder full rotation.
2100
2005
2010
2023
2050
2055
Install the sensor and magnet :
2068
2070
2083 The magnet should pass
A
2170
through the sensor line.
2145
2155
2161
2169
1938
1944
2090
2125
2105
2070
2080
2086
Sensor line
5
2096
2105
2136
3
2146 Install the sensor
2155
2130
2168
2180
2200
2288
2326
6 7
* You can also use ties 0 (in place of sensor rubber
band 6) to secure the sensor.
4
Install the magnet
Spoke
5
Toward the sensor line
* After installation, rotate the front wheel gently to check that the speed is displayed on the
computer. If the speed is not displayed, check that conditions
L mm
U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending
Copyright© 2008 CATEYE Co., Ltd.
CCRD10-080924 066600507
1 Bracket band
6
2 Bracket
3 Nut
7
4 Sensor
8
5 Magnet
6 Sensor rubber band (x2)
7 Sensor hook
8 Sensor rubber pad (x3)
9 Bracket rubber pad
0 Nylon ties (x5)
Stem
9
9
Handlebar
* For wing type handlebar or
To the sensor
The clearance between the sensor surface
B
and the magnet must not exceed 5 mm.
Inside of right
front fork
4
5
* Attach between one and three sensor pads 8,
putting them together as required.
4
Inside of right
front fork
5
Remove/install the computer
Click
push it out as if lifting the front up
ENG
6
Cut
Caution:
Round off the cut edge
of the bracket band to
prevent injury.
3
oversized stem, bracket can be
mounted using the Bracket
Holder and nylon ties. (Option).
2
Inside of right
front fork
4
0
Pull securely
While supporting it by hand,
and are satisfied.
A B