This Manual is valid for Africa, Asia, Europe, Latin America and South America as of June 1st 2022 for Q.PEAK DUO-G10.X solar modules, and replaces all earlier versions.

DISCLAIMER

This manual is subject to change. The data sheets and customer information valid at the point in time when the relevant module was manufactured apply to the installation, mounting,

and maintenance procedures for the respective solar modules, as far as no updated document is provided.

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK_DUO-G10.X

1 Introduction

With solar modules from Hanwha Q CELLS GmbH (hereafter

referred to as "Qcells") you can directly transform the sun's

limitless energy into environmentally-friendly solar electricity.

In order to ensure the maximum performance of your Qcells

solar modules, please read the following instructions carefully

and observe all guidelines. Non-compliance may result in

damage and / or physical injury.

This installation and operation manual (hereafter also referred to

as the "Manual") provides instructions for the safe installation and

operation of crystalline solar modules.

Please read these instructions carefully before proceeding with

your installation.

Please retain these instructions for the life of the solar modules.

Please ensure that this Manual is available to the operator at all

times.

This Manual should be given to all subsequent owners or users

of the solar modules.

All supplements received from the manufacturer should be

included.

Please observe all other applicable documents.

If your questions are not satisfactorily answered in the manual,

please contact your system supplier.

Additional information can be found on our website at www.

qcells.com/.

Intended use

This manual is valid for Africa, Asia, Europe, Latin America, South

America. These instructions contain information regarding the

safe handling and use of quality crystalline solar modules from

Qcells and their installation, mounting, wiring, maintenance and

disposal.

Symbols and Labels

The following symbols and labels are used throughout the

Manual for ease of use.

SYMBOL

DESCRIPTION

Procedure with one or more steps.

Lists of items.

Ensure that when carrying out a procedure,

you check the results of said procedure.

Prohibited.

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK_DUO-G10.X

Beware of possible danger or damage.

Categories:

Danger: Risk of fatal injury

■

Attention: Risk of serious injury or damage to

■

property

Note: Risk of damage to product

■

Safety Regulations

In particular the installer as well as the operator of a module

is responsible for compliance with all applicable statutory

requirements and regulations.

Unless otherwise specified by any laws or regulations, the

following stipulations must be upheld at all times during the

installation, operation, and maintenance of the solar modules:

This manual.

■

Other applicable stipulations (such as country-specific

■

regulations for pressure equipment, operational safety,

hazardous goods, and environmental protection).

Regulations and requirements specific to the system.

■

Any applicable laws and requirements, in particular

■

international, country specific, regional laws and stipulations

governing the planning, installation, and operation of solar

power systems and work on roofs.

Any valid international, national and regional regulations

■

governing work with direct current, especially those

applicable to the installation of electrical devices and

systems, and regulations issued by the respective energy

provider governing the parallel operation of solar power

systems.

Any international, country specific and regional accident-

■

prevention regulations.

Other applicable stipulations provided by the relevant

■

national institutions regarding safety in the installation and

operation of electrical items.

Qualified and Skilled Personnel

Both, the installer and operator are responsible for ensuring that

the installation (including connection to the grid), maintenance

and dismantling are carried out by trained and qualified

specialists with approved training certificates (issued by a state

or federal organization) for the respective specialist trade.

Electrical work may only be performed by an officially certified

tradesperson in accordance with the stipulations applicable in

the relevant country with regard to standard and regulations

(in Germany e. g. DIN standards, VDE regulations) and the

stipulations of the local grid operator and / or energy provider.

Table of Contents

This manual is also suitable for:

Q.peak duo-g10 seriesQ.peak duo-g10Q.peak duo-g10.a Q.peak duo blk-g10 Q.peak duo blk-g10.a Q.peak duo-g10.4 ... Show all

Table Of Contents - Qcells Q.PEAK DUO-G10.X Series Operating And Maintenance Instructions Manual