Table of Contents
Advertisement
ADJUSTMENT PROCEDURE
Item / Preparation
+B SET-UP
1.
Receive a Greyscale signal.
2.
Set the controls :-
Brightness
Minimum
Contrast
Minimum
Volume
Minimum
Cut Off
1. Receive a Greyscale signal.
2. Degauss the tube externally.
3. Set the TV into Service Mode 1.
4. Select Cut off mode.
SELF CHECK
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To get into the Self-Check mode
press the down (-/v) button on the customer controls at the front of the set,at the same time pressing the STATUS
button on the remote control, and the screen will show :-
Self Check is also used to automatically check the bus lines and hexadecimal code of the TV set. If the CCU ports have
been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.". For more in-depth TV
diagnostics use the LUCI interface as listed below.
Service Aids
To aid in the service of our current chassis there are a number of Service Aids which have been made available.
•
LUCI interface kit (Linked Utility Computer Interface)
Part number: TZS6EZ002
This contains interface and cables for connecting TV service connector and a PC as well as diagnostic software. As new
models are introduced upgrade software will become available.
•
VICI (Visual Interactive Computer Information)
These C.D.'s contain multimedia documentation providing quick access to service information.
Part No. TZS7EZ006 & TZS7EZ005
1. Service Manuals
2. Instruction Books
3. Technical Information
•
TASMIN (Technically Advanced System for Multimedia Interactive Notes)
As well as providing a first step towards more interactive training this product also achieves quick access to Technical
Information.
All manuals and user guides at all-guides.com
Adjustments
1. Confirm the following voltages.
D-Board
D3
PIN5 147V ± 3V
D12
PIN5 5V
D13
PIN1 40V
D3
PIN4 230V ± 10V
D3
PIN4 205V ± 10V
D3
PIN4 190V ± 10V
D3
PIN4 190V ± 10V
D14
PIN5 5V
D12
PIN7 15V
D12
PIN9 15V
D11
PIN8 12V
D11
PIN10 33V
Adjust the screen VR until the display shows "O.K."
VPC
O.K.
TUN
O.K.
PCB
E2
O.K.
Cab
DPL
- -
CIP1
O.K.
Sum
CIP2
O.K.
VP
O.K.
DFU
O.K.
COL
O.K.
PIP
O.K.
DIS
O.K.
OPTION 1
BD
{BD}
OPTION 2
FD
{DD}
OPTION 3
1F
{1F}
OPTION 4
08
{08}
OPTION 5
FF
{FF}
OPTION 6
63
{63}
5
E-Board
U8A
E19-PIN8
± 0,3V
U9
IC3801-PIN3 9V
± 4V
U12
E22-PIN8
STD5VE26-PIN4
U15
E23-PIN8
U15
E23-PIN9
U33
E22-PIN10
± 0,5V
U40
E24-PIN1
± 2V
U5B
E19-PIN5
± 2V
± 2V
± 3V
O.K.
O.K.
Factory use
only
8V
± 0,5V
± 0,5V
12V
± 0,5V
5V
± 0,5V
15V
± 1V
-15V ± 1V
33V
± 4V
40V
± 3V
5V
± 0,5V
Advertisement
Table of Contents
