Advertisement
Quick Links
OWNER / OPERATOR MANUAL
— LRT-A Applicable Model —
LRTZ2500
BC2601DL
BCX2600S
RMSZ2500
SGCX2600S
PSZ2500
LRT2300*
BC2300DL*
NOTE: *marked models - DO NOT USE
#65 Spacer (6367-13990)
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
APPLICABLE SERIAL NUMBERS :
CUTTING UNIT 000000 and up
TRIMMER ATTACHMENT
LRT-A
BCZ2500S/SU
SGCZ2500S
BC2600DL*
WARNING
Before using our trimmers, please
read this manual carefully to
understand the proper use of your
unit.
6782-93190 (004)
Advertisement
Related Manuals for RedMax BCZ2500S/SU
Summary of Contents for RedMax BCZ2500S/SU
- Page 1 California to cause cancer, birth defects or other reproductive harm. APPLICABLE SERIAL NUMBERS : CUTTING UNIT 000000 and up LRT-A BCZ2500S/SU SGCZ2500S BC2600DL* Before using our trimmers, please read this manual carefully to understand the proper use of your unit.
- Page 2 INFORMATION This machine is equipped with an Overload Cancellation Mechanism. When the cutting blades have got into metal wires or those twigs difficult to cut, the mechanism acts as a shock absorber, and protects the drive gears and the blades from severe reaction which could give damage to those parts.
-
Page 3: Table Of Contents
SAFETY FIRST Instructions contained in warnings within this manual marked with a critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. WARNINGS IN THE MANUAL WARNING This mark indicates instructions which must be... -
Page 4: Parts Location
1. Parts location 2. Specifications LRT-A Cutting head Type···········································································Reciprocating Double blade Tooth·········································································································28 teeth Pitch ···················································································································30 Effective cut width ··························································································16 in Angle adjust range ··················90°(±45° from cutting head position aligned shaft) 1. Blade 2. Gear case Specifications are subject to change without notice. -
Page 5: Warning Labels On The Machine
WARNING Never modify your trimmer. We won't warrant the machine, if you use the remodeled trimmer or you don't observe the proper usage written in the manual. causing serious injury or death. Read this manual carefully and practice using the trimmer until you are fully acquainted... -
Page 6: For Safe Operation
4. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product. - Page 7 4. For safe operation b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area. c. During rain storms, during lightning storms, at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the product.
- Page 8 4. For safe operation BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area.
- Page 9 4. For safe operation WARNING Never place the throttle into the high speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position.
- Page 10 3. When replacing any part, or when replacing the oil or any lubricant, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax product. 4. In the event that any part must be replaced or...
- Page 11 4. For safe operation HANDLING FUEL 1. The engine of the RedMax product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there...
-
Page 12: Set Up
1. Remove the cap on the end of the main pipe. 2. Remove the screw screwed into the end of the trimming mechanism. 3 When attaching to LRTZ2500 BC2601DL BCZ2500S/SU BCX2600S SGCZ2500S SGCX2600S and PSZ2500, insert the spacer into the trimmer mechanism as aligning the screw holes of the both. -
Page 13: Operation
• Never hold the trimmer in a way in which the blades are pointed towards someone else. • Never allow the blades to come into proximity with your body while the engine of the trimmer is in operation. - Page 14 8. Operation ADJUSTING THE ANGLE OF THE CUTTING BLADES (F2) 1. Stop the engine. 2. Turn the bolt located on the top of the trimming mechanism counter-clockwise to loosen it. 3. Adjust the angle of the blades to the desired angle, and then fix the bolt firmly back into place.
-
Page 15: Maintenance
Screwing in the screw too tightly may make it impossible for the blades to move. Conversely, not screwing in the screw tightly enough may make the blades of the trimmer feel dull and cause leaves and branches to become caught in the blades of the trimmer. - Page 16 If the blades become so worn down that it is no longer possible to eliminate the gap between them, you should contact the authorized RedMax servicing dealer from which you purchased your RedMax® trimmer to have the blades resharpened or replaced. GEAR CASE reduction...
-
Page 17: Parts List
8. Parts list TRIMMER ATTACHMENT NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. - Page 18 8. Parts list Fig.1 CUTTING UNIT LRT-A (S/N 000000 and up)
- Page 19 Fig.1 CUTTING UNIT LRT-A (S/N 000000 and up) Key# Description LEVER, clamp WASHER M6 WASHER 6x16x2.0 ANGLE ADJUSTER BOLT M6x12 CASING A SET • CASING A • PLATE GREESE FITTING LABEL SCREW M4x8 COVER SNAP RING BEBEL GEAR SNAP RING BEARING CRANK SHAFT SNAP RING...
- Page 20 ZENOAH AMERICA INC. AT (770)-381-5147. IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL OUT THE CARD AND SEND IT TO RedMax / KOMATSU ZENOA AMERICA WITHIN SEVEN (7) DAYS.BE SURE TO KEEP A COPY FOR YOUR RECORDS.
- Page 21 à compter de la date de livraison initiale d’une unité du modèle LRT-A. Telles sont les limites de la garantie. Le coût du transport de l'unité jusqu'au revendeur RedMax et depuis celui-ci sera à la charge de l'acheteur. L'acheteur ne supportera pas le coût de main d'oeuvre du diagnostic qui amène à la conclusion qu'une pièce garantie est défectueuse, si ce diagnostic est effectué...
- Page 22 KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 © Printed in Japan...