Summary of Contents for Interlogix TruVision Wedge
- Page 1 TruVision Wedge Dome Back Box and Dual View Mount Installation Guide P/N 1073093A-EN • REV A • ISS 30SEP15...
- Page 2 Copyright © 2015 United Technologies Corporation, Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved. Trademarks and patents Trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
-
Page 3: Table Of Contents
Installation 12 Specifications 23 TruVision wedge camera bracket and mount 23 Product overview This is the installation guide for the following TruVision wedge camera models: TVW-DVM (dual view mount) (use with TVD-PPB) TVW-AWB-1 (angled back box for outdoor application) ... -
Page 4: Product And Package Contents
Product and package contents Check the package and contents for visible damage. If any components are damaged or missing, do not attempt to use the unit; contact the supplier immediately. If the unit is returned, it must be shipped back in its original packaging. TVW-DVM dual view mount The TVW-DVM dual view mount (purchased separately) allows you to install two panoramic cameras on a single mount. - Page 5 Template B: Template A Screw 3 x 10 m (5 pcs m): Screw (10 pcs): Drywall anchor 7.5 x 24.5 mm M4 screw 4 x 25 mm Screw 3 x 8 mm (2 pcs): Screw 4 x 10 mm (5 pcs): Rubber ring: Installation Guide...
-
Page 6: Tvw-Awb-1 Outdoor Angled Back Box
Figure 1: Cameras attached using the dual view mount TVW-AWB-1 outdoor angled back box The TVW-AWB-1 outdoor angled back box (purchased separately) is weather resistant and includes a G1 threaded conduit access and plug. It conceals the interconnect cables and eliminates the blind area below the camera when the camera is installed on a wall. - Page 7 Tube adapter (30 x 12 mm): Conduit cover/plug: Template A: Rubber ring: Screw (5 pcs): Screw 3 x 10 mm (5 pcs): Drywall anchor 7.5 x 24.5 mm M4 screw 4 x 25mm Screw 3 x 8 mm (2 pcs): Screw 4 x 10 mm (3 pcs): Installation Guide...
-
Page 8: Tvw-Awb-2 Indoor Angled Back Box
Figure 2: Camera mounted on an outdoor back box TVW-AWB-2 indoor angled back box The TVW-AWB-2 indoor angled back box (purchased separately) conceals the interconnected cables and eliminates the blind area below the camera when the camera is installed on a wall. Camera back box: Installation Guide... -
Page 9: Tvw-2G-Ad Adapter Plate
Template B Screw 5 pcs: Drywall anchor (7.5 x 24.5 mm) M4 screw (4 x 25 mm) Screw 3 pcs (4 x 10 mm): Figure 3: Camera mounted on an indoor back box TVW-2G-AD adapter plate The TVW-2G-AD adapter plate (purchased separately) allows you to attach the panoramic wedge camera to a standard 4-inch 2 gang box. - Page 10 Camera adapter plate: Template A: Rubber ring: Installation Guide...
- Page 11 Screw 5 pcs: Screw 3 x 8 mm (2 pcs): Drywall anchor (7.5 x 24.5 mm) M4 screw (4 x 25 mm) Screw 4 x 10 mm (3 pcs): Figure 4: Wedge camera attached to a 2 gang box Installation Guide...
-
Page 12: Installation
Installation To mount two wedge cameras on a dual view mount: Attach the TVW-DVM dual view mount to an installed pendant mount tube. An adapter is included in the kit that, if required, can be used to match-up with the threading (G1 male or G1 female) of the pendant mount tube. - Page 13 Pull the cables through the bracket tube and to both back boxes, conect the cables to cameras and place the connecters and cables into the back boxes. Mount the two cameras on both sides of the TVW-DVM dual view mount. Installation Guide...
- Page 14 Re-attach the camera covers to the cameras. To mount the wedge camera on an outdoor angled back box: Drill the holes for the mounting hardware in the mounting surface using the supplied drill template. Installation Guide...
- Page 15 Detach the TVW-2G-AD adaptor plate from the back box. Mount the TVW-2G-AD adaptor plate to the mounting surface using the supplied hardware. Mount the outdoor angled back box to the TVW-2G-AD adaptor plate using the supplied hardware. Installation Guide...
- Page 16 Loosen the screws with the tamper-resistant hex wrench (supplied) to remove the camera cover. Connect the cables, conceal the cables and connectors inside the back box and mount the camera base to the outdoor angled back box. Installation Guide...
- Page 17 Re-attach the dome cover to the camera. To mount the wedge camera on an indoor angled back box: Drill the holes for the mounting hardware in the mounting surface using the supplied drill template. Installation Guide...
- Page 18 Mount the indoor back box to the mounting surface by using the supplied hardware. Loosen the screws with the tamper-resistant hex wrench (supplied) to remove the camera cover. Installation Guide...
- Page 19 Connect the cables, conceal the cables and connectors inside the back box, and mount the camera base to the indoor angled back box. Re-attach the dome cover to the camera. Installation Guide...
- Page 20 To mount the wedge camera on a 2-gang box: Install the 2-gang box (separately purchased) in the wall according to the local applicable codes and regulations Attach the TVW-2G-AD adapter to a pre-installed 2-gang box on wall. Installation Guide...
- Page 21 Attach the enclosed rubber ring to the 2-gang box adapter. Loosen the screws with the tamper-resistant hex wrench (supplied) to remove the camera cover. Installation Guide...
- Page 22 Connect the cables, conceal the cables and connectors inside the 2-gang box and mount the camera base to the 2-gang box adapter. Re-attach the camera cover to the camera. Installation Guide...
-
Page 23: Specifications
Specifications TruVision wedge camera bracket and mount TVW-DVM Dimensions (L × W × H) 134.2 × 131.2 × 86.2 mm (5.28 × 5.16 × 3.9 in.) Weight 422 g (0.93 lb.) TVW-AWB-1 Dimensions (L × W × H) 134.1 × 130.9 × 54 mm (5.27 ×... - Page 24 TVW-AWB-2 Dimensions (L × W × H) 133.9 × 130 × 32.2 mm (5.27 × 5.12 × 1.26 in.) Weight 101 g (0.22 lb.) TVW-2G-AD Dimensions (L × W × H) 134.1 × 130 × 13.5 mm (5.27 × 5.12 × 0.53 in.) Weight 129 g (0.28 lb.) Installation Guide...