Maintenance And Care - Vitek VT-1903 Instruction Manual

ENGLISH
is detected or after it has fallen, unplug the unit
and apply to any authorized service center at the
contact addresses given in the warranty certifi-
cate and on the website www.vitek.ru.
•
Transport the unit in the original package.
•
Keep the unit in a dry cool place out of reach of
children and people with disabilities.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After the unit transportation or storage at low
temperature keep it for at least three hours at
room temperature before switching on.
FAN ASSEMBLING
The fan is supplied disassembled. Do not con-
nect the unit to the mains, if it is not completely
assembled.
•
Unpack the unit and remove any stickers that
can prevent its operation.
•
Check the unit for damages; do not use it in case
of damages.
•
Assemble the floor support (4) according to the
pictures 1-6: match the locks (9) and the clamps
(6) on both halves of the stand (4) (pic. 4 and 5)
and put them together until clicking. Pass the
power cord through the installation opening of
the stand (8).
•
Install the bottom part of the fan body into the
assembled stand (4) and fix it with the clamp-
ing nut (10).
•
Fix the power cord (5) in the power cord duct (11).
USAGE
Before using the unit for the first time, make sure
that the voltage in your mains corresponds to the
unit operating voltage.
•
Insert the power plug into the mains socket.
•
Press the on/off button (15), you will hear a
sound signal and the unit will be switched on.
•
Select the airflow speed pressing the «Speed»
button (16) alternately on the control panel (1)
or the button (16) on the remote control (18);
the indicators on the display (12) inform about
the selected airflow speed. The unit has total
3 speed modes - H/ M / L.
•
Switch the oscillation mode on by pressing the
button (17) on the control panel (1) or the but-
ton (17) on the remote control (18); to switch the
oscillation mode off, press the button (17) again.
• Set the automatic switch-off timer operation
time by pressing the button (14) on the control
panel (1) or the button (14) on the remote con-
trol (18); the light indicators will inform about the
set operation time. You can set the fan opera-
tion time between 1 and 12 hours with a 1 set-
ting step. To switch the timer off press the button
(14) repeatedly until all the indicators go out.
•
You can switch the air flow mode on with the but-
ton (13), it has 3 options:
«Normal» – normal operating mode;
«Natural» – the air flow speed will increase and
decrease gradually;
«Sleep» – night mode.
•
To switch the mode on, consequently press
the button (13) until the corresponding indica-
tor appears on the display (12) and sets to the
desired mode. To switch the mode off, press the
button (13) until the indicator goes out.
Using the remote control (18):
•
Remove the battery compartment lid of the
remote control (18) and insert a «CR2025» type
battery, strictly following the polarity. Close the
battery compartment lid.
•
If you do not use the unit for a long time, remove
the batteries from the battery compartment of
the remote control (18).
Note:
– Replace the batteries in the remote control (18)
in time, to avoid damage of the remote con-
trol (18), prevent leaking of batteries.
Attention!
Functions of the buttons on the remote control (18)
fully correspond to the buttons on the control
panel (1).
• You can place the remote control (18) in the
socket (7) on the rear side of the fan body.

MAINTENANCE AND CARE

•
Before cleaning the fan switch it off and remove
the plug of the power cord from the socket.
•
Wipe the fan body with a soft, slightly damp cloth
and then wipe it dry.
• Do not use solvents or abrasives for cleaning
the unit body.
•
Do not immerse the fan body, the power cord (5)
and the plug into water or any other liquids; pro-
vide that water does not get into the fan body to
avoid electric shock or damaging the unit.
4