Summary of Contents for Detecto APSWIFI
- Page 1 APSWIFI Enterprise WIFI Option Installation and Setup Manual 8527-0570-0M Rev C • APSWIFI Installation and Setup...
- Page 2 8527-0570-0M Rev C • APSWIFI Installation and Setup...
-
Page 3: Fcc Compliance Statement
Federal Communications Commission helpful. It is available from the U.S. Government Printing Office, Washington, D.C. 20402. Stock No. 001-000-00315-4. PRECAUTIONS Before using this device, read this manual and pay special attention to all NOTIFICATION symbols: ELECTRICAL STATIC IMPORTANT WARNING SENSITIVE 8527-0570-0M Rev C • APSWIFI Installation and Setup... -
Page 4: Proper Disposal
Please do your part by making certain that this device is properly disposed of. The symbol shown to the right indicates that this device must not be disposed of in unsorted municipal waste programs. II II 8527-0570-0M Rev C • APSWIFI Installation and Setup... -
Page 5: Specifications
APS Enterprise Scale was built with quality and reliability at our factory in Webb City, MO USA. The APSWIFI option is used to connect the APS scale to an IEEE 802.11b/g wireless local area networks (wireless LAN). When the scale is powered on, the APSWIFI will connect to a wireless LAN matching the configuration stored in the APSWIFI module. -
Page 6: Installation
Connection to the APS Enterprise scale is made internally to the main board inside the scale. The APSWIFI uses an RJ11 snap-in modular connector and can be connected to either Serial Port 1 or Serial Port 2. Note that if the APSWIFI is connected to Serial Port 2, the Remote Display cannot be used. -
Page 7: Network Configuration
NETWORK CONFIGURATION Connecting to APSWIFI Access Point (Ad Hoc) From the initial factory settings, the APSWIFI will appear as a wireless access point with the name “CardinalS2W. In order to connect to the APSWIFI for initial setup, you will need to connect to it as a wireless access point using a wireless device such as a laptop, PC, tablet or smart phone. - Page 8 To reset the APSWIFI to defaults, set the jumper in the shorted position and apply power to the scale. You should see the DEFAULT LED (D3) light up while the APSWIFI is in the process of resetting the configuration. When the reset to defaults is complete you should see the LED flash 5 times and then go out when it is complete.
- Page 9 NETWORK CONFIGURATION, CONT. Web Configuration Parameter Descriptions – Access Point The configuration web page in the APSWIFI module allows the module to be configured as either an access point, or to connect to an existing network. In order to accomplish this, a new parameter has been added on the web page “Network Mode”.
- Page 10 Network Mode – This parameter allows the APSWIFI module to be configured as either an access point, or to connect to an existing network. In order to set up the APSWIFI module as an access point, set the mode to “Server (SoftAP).
- Page 11 NETWORK CONFIGURATION, CONT. Web Configuration Parameter Descriptions – Client (Infrastructure) The configuration web page in the APSWIFI module allows the module to be configured as either an access point, or to connect to an existing network. In order to accomplish this, a new parameter has been added on the web page “Network Mode”.
- Page 12 Mode” to “Client (Infrastructure)”. Available Access Points – Click the “Refresh List” button in order to scan for available access points that the APSWIFI module can connect to. You can select an AP by clicking on its name in the list.
-
Page 13: Troubleshooting
TROUBLESHOOTING Status LED’s The APSWIFI has four (4) LED’s to indicate the communication status of the wireless connection. DEFAULT LED D3 LED D6 LED D5 DISC LED D4 LED Indication Description This LED will illuminate to indicate the APSWIFI is in the process of DEFAULT resetting the configuration. -
Page 14: Parts Identification
CONNECTOR, 6-PIN MODULAR 6540-0150 ENCLOSURE, POLYCARBONATE 6680-1015 SPACER, #4 X .375 SELF RETAINING 6021-1100 SCREW, PAN HD. #4-40 X .69 8527-C511-0A PC BOARD 6980-1046 CABLE, 6 COND. 26 GA. MODULAR, 74” LONG 8527-0570-0M Rev C • APSWIFI Installation and Setup... -
Page 15: Statement Of Limited Warranty
(2) years from date of shipment. Detecto shall be the sole judge of what constitutes a defect. During the first ninety (90) days Detecto may choose to replace the product at no charge to the buyer upon inspection of the returned item. - Page 16 Cardinal Scale Manufacturing Co. 102 E. Daugherty, Webb City, MO 64870 USA Ph: 417-673-4631 or 1-800-641-2008 Fax: 417-673-2153 Technical Support: 1-866-254-8261 Printed in USA E-mail: tech@cardet.com 8527-0570-0M Rev C 06/19 8527-0570-0M Rev C • APSWIFI Installation and Setup...