Page 3
® The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Chapter 1: Introduction Thank you for purchasing ASRockInd IMB-X1233-WV motherboard, a reliable motherboard produced under ASRockInd’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRockInd’s com- mitment to quality and endurance. In this manual, chapter 1 and 2 contain introduction of the motherboard and step- by-step guide to the hardware installation.
1.2 Specifications Form Dimensions Mini-ITX (6.7-in x 6.7-in) Factor ® Intel 12th Gen (Alder Lake-S) Core™ Processors, up to 65W Processor ® Chipset Intel W680 System Socket LGA1700 BIOS AMI SPI 256 Mbit Technology Dual Channel DDR4 3200 MHz Memory Capacity 64GB (32 GB per DIMM) Socket...
Page 7
2 x USB 3.2 Gen1 (1 x USB 3.2 header) 4 x USB 2.0 (1 x 2.54 pitch header) COM1, COM2 (RS-232/422/485) COM3, COM4 (RS-232) GPIO 4 x GPI, 4 x GPO Internal TPM 2.0 onboard IC Connector LVDS SATA PWR Output Speaker Header...
1.4 I/O Panel USB 3.2 Gen2 Ports (USB3_1_2) LAN RJ-45 Port (LAN2)* USB 3.2 Gen12 Ports (USB3_7_8) LAN RJ-45 Port (LAN1)* HDMI Port (HDMI1) Line out (Lime) DisplayPort (DP1) Microphone (Pink) DisplayPort (DP2) DC Jack (DC_JACK1) * There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.
Chapter 2: Installation This is a Mini-ITX form factor (6.7” x 6.7”) motherboard. Before you install the moth- erboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard.
2.3 Installation of Memory Modules (SO-DIMM) This motherboard provides two 260-pin DDR4 (Double Data Rate 4) SO-DIMM slots. Step 1. Align a SO-DIMM on the slot such that the notch on the SO-DIMM matches the break on the slot. 1. The SO-DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the SO-DIMM if you force the SO-DIMM into the slot at incorrect orientation.
2.4 Expansion Slots There is 1 PCI Express slot, 4 M.2 sockets and 1 SIM socket on this motherboard. PCIE slot: PCIE1 (PCIE 4.0 x16 slot) is used for PCI Express x16 lane width cards*. *Supports riser card x8/x8. M.2 sockets: 1 x M.2 (Key E, 2230) with PCIe x1, USB 2.0 and CNVi for Wireless.
2.5 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”...
Page 15
Digital Input / Output Power Select 1-2 : +12V 2-3 : +5V (3-pin JGPIO_PWR1) (see p.8, No. 9)
2.6 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! CPU Fan Connector Please connect the CPU fan cable to the connector and (4-pin CPU_FAN1)
Page 17
RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating.
Page 18
USB 2.0 Headers There are two headers on this motherboard. Each USB 2.0 (9-pin USB2_5_6, USB2_10_11: header can support two ports. see p.8, No. 35) USB 3.2 Gen1 Header There is one header on this Vbus Vbus motherboard. This USB 3.2 Vbus IntA_PB_SSRX- (19-pin USB3_4_9,...
Page 19
LVDS Panel Connector* Signal Name Signal Name LCD_BLT_VCC LCD_BLT_VCC (40-pin LVDS1) CON_LBKLT_CTL LCD_BLT_VCC CON_LBKLT_EN (see p.8 No. 15) LVDS_B_CLK# LVDS_B_CLK LVDS_B_DATA3 DPLVDD_EN LVDS_B_DATA3# LVDS_B_DATA2# LVDS_B_DATA2 LVDS_B_DATA1 LVDS_B_DATA1# LVDS_B_DATA0# LVDS_B_DATA0 LVDS_A_CLK LVDS_A_CLK# LVDS_A_DATA3# LVDS_A_DATA3 LVDS_A_DATA2 LVDS_A_DATA2# *eDP Connector (on the Backside of PCB) LVDS_A_DATA1# LVDS_A_DATA1 LVDS_A_DATA0...
Page 20
SATA Power Connector Please connect a SATA +12V power cable to this connector. (SATA_PWR1) (see p.8 No. 5) ATX Power Connector Please connect a DC power supply to this (4-pin DC_4PIN1) connector. (see p.8 No. 30) 1-2 : GND 3-4 : DC Input UPS Module Power Input Connector Pin1 : GND Pin2 : DC Input...
Page 21
SMBUS_TEST1 (4-pin SMBUS_TEST1) (see p.8 No. 24) Power Adapter Signal Name (4-pin POWER_ADAPTER) (see p.8 No. 27) 5VA_CONTROL AT_TEST1_PCIE_PWR1 Signal Name (4-pin AT_TEST1_PCIE_PWR1) AT_TEST1 (see p.8 No. 22) PCIE_PWR1 (For VGA Power Card Only): Pin3: PSON# Pin4: GND Panel Power Select (LCD_VCC) 1-2 : LCD_VCC: +3V 2-3 : LCD_VCC: +5V (5-pin PNL_PWR1)
2.7 Installation of ROM Socket * Do not apply force to the actuator cover after ic inserted. * Do not apply force to actuator cover when it is opening over 120 degree, Otherwise, the actuator cover may be broken. * The yellow dot (Pin1) on the ROM must be installed at pin1 position of the socket (white arrow area).
Chapter 3: UEFI SETUP UTILITY 3.1 Introduction This section explains how to use the UEFI SETUP UTILITY to configure your system. The UEFI chip on the motherboard stores the UEFI SETUP UTILITY. You may run the UEFI SETUP UTILITY when you start up the computer. Please press <F2>...
3.1.2 Navigation Keys Please check the following table for the function description of each navigation key. Navigation Key(s) Function Description Moves cursor left or right to select Screens Moves cursor up or down to select items + / - To change option for the selected items <Enter>...
3.3 Advanced Screen In this section, you may set the configurations for the following items: CPU Configu- ration, Chipset Configuration, Storage Configuration, Super IO Configuration, AMT Configuration, ACPI Configuration, USB Configuration and Trusted Computing. Setting wrong values in this section may cause the system to malfunction.
3.3.1 CPU Configuration Intel Hyper Threading Technology Intel Hyper Threading Technology allows multiple threads to run on each core, so that the overall performance on threaded software is improved. Active Processor P-Cores Select the number of cores to enable in each processor package. Active Processor E-Cores Select the number of E-Cores to enable in each processor package.
Page 27
Intel Turbo Boost Technology Use this item to enable or disable Intel Turbo Boost Mode Technology. Turbo Boost Mode allows processor cores to run faster than marked fre- quency in specific conditions. The default value is [Enabled]. CPU Thermal Throttling You may select [Enabled] to enable CPU internal thermal control mechanism to keep the CPU from overheating.
3.3.2 Chipset Configuration Primary Graphics Adapter This allows you to select [Onboard] or [PCI Express] as the boot graphic adapter priority. The default value is [PCI Express]. Above 4G Decoding Enable or disable 64bit capable Devices to be decoded in Above 4G Ad- dress Space (only if the system supports 64 bit PCI decoding).
Page 29
(F9 load default is also set to ENABLE). Change the setting from [Enable] to [Disable], and then press <F10> to save the setting and restart the sys- tem. Likewise, the default value of Active LVDS is changed to DISABLE (F9 load default is also set to DISABLE) Onboard LAN1 This allows you to enable or disable the Onboard LAN1 feature.
3.3.3 Storage Configuration VMD Configuration This item allows you to enable or disable the Intel VMD support function. SATA Controller(s) Use this item to enable or disable the SATA Controller feature. SATA Mode Selection Use this to select SATA mode. The default value is [AHCI Mode]. AHCI (Advanced Host Controller Interface) supports NCQ and other new features that will improve SATA disk perfor- mance but IDE mode does not have these advantages.
3.3.4 Super IO Configuration COM1 Configuration Use this to set parameters of COM1. Type Select Use this to select COM1 port type: [RS232], [RS422] or [RS485]. COM2 Configuration Use this to set parameters of COM2. Type Select Use this to select COM2 port type: [RS232], [RS422] or [RS485]. COM3 Configuration Use this to set parameters of COM3.
3.3.5 AMT Technology USB Provisioning of AMT Use this to enable or disable AMT USB Provisioning. The default is [Dis- abled]. MAC Pass Through Use this to enable or disable MAC Pass Through. The default is [Disabled]. Activate Remote Assistance Process Trigger CIRA boot.
Page 33
OCR PBA Boot Use this to enable or disable One Click Recovery PBA Boot. The default is [Enabled]. OCR Windows Recovery Boot Use this to enable or disable One Click Recovery Windows Recovery Boot. The default is [Enabled]. OCR Disable Secure Boot Use this to allows CSME to request Secure Boot to be disabled for One Click Recovery.
3.3.6 ACPI Configuration Suspend to RAM Use this item to select whether to auto-detect or disable the Suspend-to- RAM feature. Select [Auto] will enable this feature if the OS supports it. PCIE Devices Power On Use this item to enable or disable PCIE devices to turn on the system from the power-soft-off mode.
3.3.7 USB Configuration USB Power Control Use this option to control USB power. M.2 Key_B USB Configuration Enable or disable M.2 Key_B USB Configuration.
3.4 Hardware Health Event Monitoring Screen In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage. CPU_FAN1 Setting This allows you to set CPU fan 1’s speed.
3.5 Security Screen In this section, you may set, change or clear the supervisor/user password for the system. Supervisor Password Set or change the password for the administrator account. Only the ad- ministrator has authority to change the settings in the UEFI Setup Utility. Leave it blank and press enter to remove the password.
3.6 Boot Screen In this section, it will display the available devices on your system for you to config- ure the boot settings and the boot priority. Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature. Setup Prompt Timeout This shows the number of seconds to wait for setup activation key.
3.7 Exit Screen Save Changes and Exit When you select this option, it will pop-out the following message, “Save configuration changes and exit setup?” Select [OK] to save the changes and exit the UEFI SETUP UTILITY. Discard Changes and Exit When you select this option, it will pop-out the following message, “Discard changes and exit setup?”...
Chapter 4: Software Support 4.1 Install Operating System ® ® This motherboard supports various Microsoft Windows operating systems: 11 64- bit / 10 64-bit. Because motherboard settings and hardware options vary, use the setup procedures in this chapter for general reference only. Refer your OS docu- mentation for more information.