Related Manuals for Genie WONVR18P5
Summary of Contents for Genie WONVR18P5
- Page 1 8 Channel H.265 Optimised NVR with 1HDD Bay WONVR18P5 Quick Start Guide Please read these instructions carefully before operating the unit and keep for further reference.
- Page 2 Intro Section Please read this instruction carefully before operating the product and keep it for further reference. All examples and pictures used here are for reference only. The contents of this manual are subject to change without notice. This device should be operated only from the type of power source indicated on the marking label.
-
Page 3: Table Of Contents
Contents 1.0 Introduction ......................4 1.1 Product Features ...................4 1.2 Product Dimensions ..................4 1.3 Specification....................5 2.0 HDD Installation ....................6 3.0 Rear Panel Instruction ..................7 4.0 Start Up and Shut Down ..................8 5.0 Login and Disk Settings ..................9 5.1 Login ......................9 5.2 Disk Settings ....................9 6.0 Configurations and Connections ................10 6.1 Network Configuration &... -
Page 4: Introduction
1.0 Introduction The Genie ‘Optimised’ WONVR18P5 PoE Network video recorders offer 8 channel recording of up to 5 Mega Pixels on every channel. The WONVR18P5 NVR supports 8 channel simultaneous playback with 8 ports of PoE. 1.1 Product Features •... -
Page 5: Specification
Quick Start Guide 8 Channel H.265 Optimised NVR with 1HDD Bay 1.3 Specification Model WONVR18P5 System Embedded Linux Network Input 8CH IPC input Network Access Format 5MP / 4MP / 3MP / 1080p / 960p / 720p @ 25 / 30fps... -
Page 6: Hdd Installation
2.0 HDD Installation This series of the product supports 1 SATA hard drive. Please make sure that the device is powered off before the installation. The pictures of the installation are for reference only. Loosen the screws to open the cover. 2. -
Page 7: Rear Panel Instruction
3.0 Rear Panel Instruction The interfaces of the rear panel are for reference only. Rear panel for WONVR14P5 Power Switch Power Connector Rear Panel for WONVR18P5 Name Description Connector for VGA output HDMI Connector for HDMI output Connectors for USB devices RJ 45 Ethernet port 4/8 PoE network ports;... -
Page 8: Start Up And Shut Down
4.0 Start Up and Shut Down Startup Connect the monitor and the power. 2. The device will boot and the power indicator will display blue. 3. A wizard window will pop up. Shutdown Click “Start” and then select “Shutdown” icon. This will bring up a shutdown window. The device will shut down by clicking “OK”... -
Page 9: Login And Disk Settings
5.0 Login and Disk Settings 5.1 Login You must configure the wizard window if you start the NVR for the first time. Choose the language and read the privacy statement. Then set the data, time and zone as needed. After that, set the login password. The default username is admin and the default password of admin is 123456. -
Page 10: Configurations And Connections
6.0 Configurations and Connections 6.1 Network Configuration & Adding IP Camera Enter IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the NVR and the router. 2. Enter HTTP port (the default value is 80) and server port (the default port is 6036). 3. -
Page 11: Record Settings
7.0 Record Settings There are two record modes: auto and manual. Auto Mode: Select one auto mode in the interface as shown below and then click “Next” to save the settings. Click “Advanced” to self-define a record mode. Manual Mode: Set the “Sensor Record”, “Motion Record”, “Analytics Record” and “Schedule Record”... -
Page 12: Nat
8.0 NAT You can enable the NAT function in the interface or set it in the network configuration after exiting the wizard. You can scan the QR code through the mobile surveillance APP available for iOS or Android to easily view your cameras. Web Browser Access Through NAT Function G to Start →... -
Page 13: Manual Recording And Playback
9.0 Manual Recording and Playback 9.1 Manual Recording Before recording, please install and format a HDD. In the live interface you can see the menu toolbar. Click button to start recording. Click it again to stop recording. You can also click to check the status of the recording. - Page 14 Sales +44(0)1707 330541 Enquiries sales@genieproducts.co.uk Website www.genieproducts.co.uk...