Page 1
All manuals and user guides at all-guides.com FILE NO. 030-200403 SERVICE MANUAL Colour Television VJ13 Chassis 43VJ33Q 50VJ33Q Published in Japan, May. 2004 (YC)
All manuals and user guides at all-guides.com TABLE OF CONTENTS CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS ............................3 CRT ASSEMBLY REPLACEMENT AND MOUNTING ....................4 PICTURE TUBE COMPONENTS ADJUSTMENT ....................6 SERVICE POSITION ..............................9 SERVICE MODE ..............................10 DESIGN MODE ..............................13 ELECTRICAL ADJUSTMENT ..........................
All manuals and user guides at all-guides.com CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazard- 2.
All manuals and user guides at all-guides.com CRT ASSEMBLY REPLACEMENT AND MOUNTING CAUTION : DO NOT LOOSEN THE HEX HEAD BOLTS WITH SPRINGS (12 PCS), BECAUSE THOSE ARE FOR SEALING OF CRT COOLANT. Attention Serviceman The Hex Head Bolts with Springs.
Page 5
All manuals and user guides at all-guides.com TO REMOVE CRT (Same procedure for R, G, B) 1. Remove CRT DRIVE Board, S. V. M. COIL and DEF. YOKE from CRT. 2. Remove Lens Assembly. 3. Detach CRT Anode Cap from CRT. Anode Cap 4.
All manuals and user guides at all-guides.com WARNING : BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRE- CAUTION" AND "PRODUCT SAFETY NOTICE" ON PAGE 3 OF THIS MANUAL. PICTURE TUBE COMPONENTS ADJUSTMENT ADJUSTING PROCEDURE IN REPLACING CRT RGB FOCUS ADJUSTMENT 1.
Page 7
All manuals and user guides at all-guides.com TILT ADJUSTMENT In case of warming up of more than 2 hours under a condition that the large anode current is running through the projection Rotate R, G, B deflection yoke so that picture becomes hori- tube so that for example the all-white pattern appears, adjust zon, then fasten screw.
Page 8
All manuals and user guides at all-guides.com LOCATION OF SCREEN AND FOCUS VR'S To remove the Speaker grille and Front panel. R G B SCREEN VR's FOCUS VR's Speaker grille REPLACEMENT OF HIGH VOLTAGE CABLE 1. When replacing Anode Lead or Anode Cap with new one, remove Lead Holder from old lead as shown in ANODE LEAD figure below, and put it on new lead.
All manuals and user guides at all-guides.com WARNING : BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRE- CAUTION" AND "PRODUCT SAFETY NOTICE" ON PAGE 3 OF THIS MANUAL. SERVICE POSITION In order to assure the performance, processed wires shall be replaced after the repair work. Work procedures are as follows: 1.
All manuals and user guides at all-guides.com SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press o button once on 2) Press o button again to 3) While pressing the o button, Remote Control. keep pressing. press MENU button on TV set. Item Data or Sound Mute...
Page 11
All manuals and user guides at all-guides.com 4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL button in the service mode changes the adjustment items in the order of table-2. ( button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING &...
Page 12
All manuals and user guides at all-guides.com 8. SELF DIAGNOSTIC FUNCTION 1) Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s are executed properly. 2) During diagnosis, the following displays are shown.
All manuals and user guides at all-guides.com DESIGN MODE 1. ENTERING TO DESIGN MODE 1) Select the Service mode. 2) While pressing CALL button on Remote 3) Press MENU button on TV. and press MENU button on TV. ITEM Press DATA Press (Design mode)
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENT ITEM ADJUSTMENT PROCEDURE WIDTH 1. Call up the adjustment mode display, then select the item WID. 2. Press the VOLUME t button to get the picture so the left (WID) or right edges of raster begins to lack. 3.
Page 15
All manuals and user guides at all-guides.com Reference factory adjustment - 15 -...
Page 16
All manuals and user guides at all-guides.com Adjustment items Adjusting methods Focus adjustment (Conditions) - User adjustment: Dynamic mode, Cinema mode - To be performed after centering magnet adjustment. - Signal : Lens: R ..Crosshatch (PAL) G ..Crosshatch (PAL) B ..
Page 17
All manuals and user guides at all-guides.com Adjustment items Adjusting methods Focus adjustment Concerning items 1), 2), 3), and 5) of G adjustment, these are common to the ones on the previous page. 3. R adjustment 1) Set to the R monochrome by lens cap. 2) Receive the image of the internal crosshatched pattern.
Page 18
All manuals and user guides at all-guides.com - 18 -...
All manuals and user guides at all-guides.com CONVERGENCE ADJUSTMENT 1. SCREEN ADJUSTMENT Before proceeding to the adjustment for each screen, always The adjustment is carried out on four screens; 4 : 3 and 16 : 9 perform the adjustments for vertical size (HIT) and horizontal screens in both PAL and NTSC modes.
Page 20
All manuals and user guides at all-guides.com 2. Picture a) 50 Hz mode (PAL) ..Correcting point: Horizontal 8 x Vertical 8 (Arrow marks denote correcting point) The first picture The second picture Data display Cursor (red) Screen center (Blinking) The first picture...
Page 21
All manuals and user guides at all-guides.com b) 60 Hz mode (NTSC) ..Correcting point: Horizontal 8 x Vertical 7 (Arrow marks denote correcting point) The first picture The second picture Data display Cursor (red) Screen center (Blinking) The first picture During this period, the changed data is transferred from RAM...
Page 22
All manuals and user guides at all-guides.com 3. ADJUSTING PICTURE DIMENSION (GREEN PICTURE) [4:3] 1. 50 Hz mode (PAL) Screen center (360.0) 310. (318.0) 164.5 (191.0) (63.5) Screen center (63.5) (191.0) 164.5 (318.0) (360.0) 310.5 8.5mm 8.5mm 372.5 223.5 74.5 74.5 223.5 372.5...
Page 23
All manuals and user guides at all-guides.com 4. ADJUSTING PICTURE DIMENSION (GREEN PICTURE) [16:9] 1. 50 Hz mode (PAL) Screen center (270.2) 232. (238.4) 205. (143.2) 123.4 (47.9) 41.3 Screen center (47.9) 41.3 (143.2) 123.4 (238.4) 205.5 (270.2) 232.9 8.5mm 8.5mm 372.
Page 24
All manuals and user guides at all-guides.com 5. Deflection amplitude setting (HIT/WID adjusting method under muted convergence) * Green pattern under the muted convergence Screen edge 0 point 2nd flag 1st flag Castration border line Horizontal amplitude: Left and right register marks of Philips pattern C + D = 8 (See A of the upper figure.) Vertical amplitude: The point where the 3rd vertical line outer from the upper and lower register marks of Philips pattern is overlapped with flags contacts the screen edge.
All manuals and user guides at all-guides.com SCREEN AND MIRROR ALIGNMENTS ASSEMBLING AND MOUNTING OF FRONT SCREEN * Please refer to MECHANICAL DISASSEMBLY page 32. CLEANING OF LENS AND MIRROR CAUTION : Do not hold the optical system parts (lens and mirror) with bare hand to avoid finger-prints on the surface of those parts.
All manuals and user guides at all-guides.com CIRCUIT CHECKS HIGH VOLTAGE CHECK CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below. 1. Connect an accurate high voltage meter to the anode of the picture tube. 2.
All manuals and user guides at all-guides.com CHAPTER 2 SPECIFIC INFORMATIONS SETTING & ADJUSTING DATA SAFETY INSTRUCTIONS 43"/50" HIGH VOLTAGE AT ZERO BEAM: 31.3 kV MAX HIGH VOLTAGE: 33.3 kV AC VOLTAGE 220~240 V Table-1 SERVICE MODE ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE: Item Adjustment Reference data...
All manuals and user guides at all-guides.com LOCATION OF CONTROLS 43VJ33Q 50VJ33Q Power Button RED-Power On RED-Power On Power Button - 28 -...
Page 29
All manuals and user guides at all-guides.com Remote Control Key To display teletext To bring up on-screen information and for the teletext initial/index function For On/Standby mode Number buttons To select input from external sources To access sub-pages when in teletext To return to the previous programme mode Aspect ratio (16:9 or 4:3)
All manuals and user guides at all-guides.com PROGRAMMING CHANNEL MEMORY Auto tune Programm skip Before running Auto tune put your decoder and video To prevent certain programmes from being viewed, the recorder to Standby. To set up the TV use the buttons programme position can be skipped and the remote on the remote control.
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. ∗ • The PC board assembly with mark is no longer available after the end of the production. Model : 43VJ33Q / 50VJ33Q Capacitors ..... CD Ceramic Disk : Plastic Film : Electrolytic Resistors ....
Page 33
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description C481 24666101 ELECTROLYTIC 04Q, 16V 100UF M 3A C735 24092730 CERAMIC CHIP, 16V B 0.1UF K C482 24591223 PLASTIC FILM, 50V 0.022UF J C736 24100104 CERAMIC CHIP, 25V F 0.1UF Z C483 24591223...
Page 34
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description C864 24092474 CERAMIC DISC, 2KV B 220PF K C7729 24212331 CERAMIC DISC, 50V B 330PF K C866 24503049 PLASTIC FILM, 63V 0.47UF J C7730 24212101 CERAMIC DISC, 50V B 100PF K C867 24591682...
Page 35
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description CR02 24092538 CERAMIC CHIP, 10V F 1UF Z R121 24011103 CHIP, METAL FILM, 1/20W 10K OHM J CR03 24092538 CERAMIC CHIP, 10V F 1UF Z R122 24011221 CHIP, METAL FILM, 1/20W 220 OHM J...
Page 36
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description R373 24011823 CHIP, METAL FILM, 1/20W 82K OHM J R483 24366103 CARBON FILM, 1/6W 10K OHM J R374 24011104 CHIP, METAL FILM, 1/20W 100K OHM J R484 24552821 OXIDE METAL FILM, 1/2W 820 OHM J...
Page 37
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description R728 24011221 CHIP, METAL FILM, 1/20W 220 OHM J R891 24366152 CARBON FILM, 1/6W 1.5K OHM J R729 24011221 CHIP, METAL FILM, 1/20W 220 OHM J R901 24366101 CARBON FILM, 1/6W 100 OHM J...
Page 38
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description R7197 24011100 CHIP, METAL FILM, 1/20W 10 OHM J RA08 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J R7198 24011221 CHIP, METAL FILM, 1/20W 220 OHM J RA09 24011103 CHIP, METAL FILM, 1/20W 10K OHM J...
Page 39
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description RB96 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J RV29 24011103 CHIP, METAL FILM, 1/20W 10K OHM J RB97 24011472 CHIP, METAL FILM, 1/20W 4.7K OHM J RV30 24872750 CHIP, METAL FILM, 1/16W 75 OHM J...
Page 40
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description L404 23248242 COIL, CHOKE, TLN3495AH L4401 23289840 COIL, PEAKING, TRF4100AT L405 23221076 COIL, CHOKE, TLN1015R L4471 23289840 COIL, PEAKING, TRF4100AT L406 23248243 COIL, CHOKE, TLN3496AH LA02 23103828 INDUCTOR, BEAD, TEM2121M...
Page 41
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description Q492 23114541 TRANSISTOR, 2SA1320 QA61 23114497 TRANSISTOR, RN1406 Q501 23009660 IC, PAL/NTSC/SECAM 1CHIP TB1262AF(DRY) QB01 23205112 TRANSISTOR, 2SA1980UF-Y Q504 23205112 TRANSISTOR, 2SA1980UF-Y QB02 23114433 TRANSISTOR, 2SC1815-Y @U906D Q505 23205112 TRANSISTOR, 2SA1980UF-Y...
Page 42
All manuals and user guides at all-guides.com Location Location Parts No. Description Parts No. Description D611 23357219 DIODE, 1SS400 DR06 23357219 DIODE, 1SS400 D628 23118269 DIODE, ZENER, RD22MB2 DR07 23357219 DIODE, 1SS400 D701 23357219 DIODE, 1SS400 DR08 23357219 DIODE, 1SS400 D702 23357219 DIODE, 1SS400...
All manuals and user guides at all-guides.com SIGNAL BOARD PD0817E (U902) BOTTOM (FOIL) SIDE - 45 - - 46 -...
Page 46
All manuals and user guides at all-guides.com DEF/CONV BOARD PD0818B (U904) BOTTOM (FOIL) SIDE - 47 - - 48 -...
Page 47
All manuals and user guides at all-guides.com POWER BOARD PD0819B (U903) BOTTOM (FOIL) SIDE - 49 - - 50 -...
Page 48
All manuals and user guides at all-guides.com CRT-D/R BOARD PD1439C1 (U901A) CRT-D/G BOARD PD1439C2 (U901B) CRT-D/B BOARD PD1439C3 (U901C) BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE P907 23547450 P927 23547450 P916 Q9601 R9606 R-8500 P910 PV16A P908 PV14B C9602 P906 P926...
Page 49
All manuals and user guides at all-guides.com FRONT IN BOARD PD1103E1 (U906A:43VJ33Q) RMT IN BOARD PD1103E2 (U906B:43VJ33Q) BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE FRONT IN BOARD PD1440C1 (U906A:50VJ33Q) IND BOARD PD1103E4 (U906D:43VJ33Q) BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE SA01 PV40...