Working Time - Master MIR DRY User Manual

10. WORKING TIME

Is the closure time of the relays when a manoeuvre is commanded; the working time can be set from 5 to 240 seconds. The factory sets the "working time" to 120
sec.
ARCO
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 7 times NEXT.
«07» appears on display
04. Press STOP. The motor signals the current
value (1)
05. Press PREV and NEXT to set a new
value(2)
06. Press STOP. The motor signals the new
value (1)
(1) Example: 1 movement - pause - 5 movements = 15 sec
(2) Example: 15 sec = press PREV 1 time and NEXT 5 times
(3) Example: 15 sec = press UP 1 time and DOWN 5 times
If you try to set «Working time» lower than 5s or greater than 240s, the value is rejected and the motor makes 2 short movements down
11. RESET
This procedure restores the receiver to the default conditions (factory settings). This procedure must only be carried out by qualified
technical staff. Having carried out the reset procedure, the qualified technician must promptly carry out all the installation operations
11A. RESET USING A MEMORIZED TRANSMITTER
ü
Select, on the transmitter, the radio channel that controls the device you want to reset.
ü
Make sure that this radio channel controls only the device you want to reset.
ARCO
01. Bring the motor in an intermediate position.
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes, the
motor performs some movement
05. Press together PREV and NEXT for about
2 seconds until the motor indicates that the
reset was performed (1 moving up / down).
06. Disconnect the power supply and reinstall
the module (see section 3).
11B. RESET USING THE BUTTON INPUT
ü
Switch off power supply to the module
ü
Connect as show in figure
ü
Switch ON power supply and wait 30 seconds until the motor makes 2 alternating
movements, to indicate that factory conditions are restored.
ü
Switch off power supply to the module
ü
Restore the connections (see section 02. ELECTRICAL CONNECTIONS)
ü
Follow the instruction at section 03. FIRST INSTALLATION
All products and technical specifications given in this document are subject to variation without notice.
Unless previously and specifically authorised by the manufacturer, the device must be used exclusively with transmitters produced by the same manufacturer.
The manufacturer shall not be liable for damage resulting from improper, incorrect or unreasonable use
FLUTE, KUADRO, KORT
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 7 times DOWN.
04. Press STOP. The motor signals the current
value (1)
05. Press UP and DOWN to set a new value (3)
06. Press STOP. The motor signals the new
value (1)
●
Example: 2 movements - pause - 1 movement - pause - 1 long movement = 210 sec
●
Example: 210 sec = press PREV 21 times
●
Example: 210 sec = press UP 21 times
described at section 03. FIRST INSTALLATION
FLUTE, KUADRO, KORT
01. Bring the motor in an intermediate position.
02. Holding down STOP, press PROG for
about 1 sec, until LEDs light
03. Press 2 time UP / 9 times DOWN.
04. Press STOP. The LEDs flash, the motor
performs some movement
05. Press together UP and DOWN for about 2
seconds until the motor indicates that the
reset was performed (1 moving up /
down).
06. Disconnect the power supply and reinstall
the module (see section 3).
R
VISIO
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 7 times NEXT.
«07» appears on display
04. Press STOP. The motor signals the current
value (1)
05. Press UP and DOWN to set a new value (3)
06. Press STOP. The motor signals the new
value (1)
VISIO
01. Bring the motor in an intermediate position.
02. Press MENU, «Menu rx» appears on
display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes, the motor
performs some movement
05. Press together PREV and NEXT for about 2
seconds until the motor indicates that the
reset was performed (1 moving up / down).
06. Disconnect the power supply and reinstall
the module (see section 3).
L N
1 2
FUSE
500mA
L
N
MAIN
POWER SUPPLY
Other transmitters...
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 07»
Other transmitters...
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 29 -
Receiver reset»
DRY
CP C
3 4 5 6 7 8