Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GE 29393
Summary of Contents for GE 29393
- Page 1 29393 Deluxe Caller ID Speakerphone User’s Guide We bring good things to life.
-
Page 2: Information 2 Nformation
FCC R EGISTRATION NFORMATION Your telephone equipment is registered with the Federal Communications Commission and is in compliance with parts 15 and 68, FCC Rules and Regulations. 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating, among other information, the FCC Registration number and Ringer Equivalence Number (REN) for the equipment. -
Page 3: Table Of Contents
ABLE OF ONTENTS FCC R EGISTRATION NFORMATION ROGRAM ..2 NTERFERENCE NFORMATION OCAL ..2 ... 20 EARING OMPATIBILITY IN THE ........5 VIP (V ) ..21 NTRODUCTION MPORTANT ERSON ......6 VIP N EFORE EGIN TORING A UMBER IN ...... - Page 4 ..34 ........... 29 TORING AUSE IN EMORY EMORY ..29 IALING REQUENTLY ALLED TORING EMORY UMBERS ........34 UMBERS EVIEWING UMBERS TORED IN ....... 35 ........31 ROUBLESHOOTING EMORY ....37 ..31 ENERAL RODUCT HANGING A TORED UMBER ..........
-
Page 5: Introduction
NTRODUCTION Congratulations on purchasing this Caller ID telephone. This unit was designed to be simple to use, and you can reach its full potential more quickly by taking a few minutes to read this User’s Guide. This Caller ID telephone is a multifunction product for use with the Caller ID and Call Waiting services available from your local telephone company. -
Page 6: Before You Begin
EFORE EGIN ARTS HECKLIST Make sure your package includes the following items: Base Handset Coiled cord Telephone line cord ODULAR EQUIREMENTS You need an RJ11 type modular phone jack, which is the most common type of phone jack and might look like the one pictured here. -
Page 7: Installation & Setup
& S NSTALLATION ETUP MPORTANT NSTALLATION NFORMATION • Never install telephone wiring during a lightning storm. • Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. This phone is equipped with a data port for you to connect to an auxiliary phone device, such as a fax machine, computer modem, answering machine, or even a cordless phone. - Page 8 CAUTION: Unplug all phone cords from the wall before installing or changing batteries. 1. Use a screwdriver to loosen the screw and pry up the battery compartment door on the bottom of the phone. 2. Insert 4 AA-size alkaline batteries as shown on the diagram in the battery compartment.
-
Page 9: Nstallation
NSTALLATION ESKTOP NSTALLATION 1. Plug the coiled cord into the handset. Plug the other end into the jack on the side of the base. Place the handset in the cradle on the base. 2. Plug the line cord into jack on the back of the base. Plug the other end into a wall jack. -
Page 10: Wall Mount Installation
OUNT NSTALLATION The speakerphone can be mounted on a wall phone plate (not included). 1. Plug the phone cord into the phone jack on the back of the unit, and wrap the extra phone line around the bottom of the base. 2. - Page 11 5. Set the RINGER switch on the base to the desired loudness. 6. Set the HANDSET VOLUME switch as desired. 7. The unit is properly installed if you pick up the handset and hear the dial tone. Otherwise, recheck all installation steps.
-
Page 12: Aller Id Set
ID S ALLER There are four programmable menus available: Local Area Code, Regional Area REVIEW button OPTION button Code, Language, and T/P Dial Mode. You should not plug the telephone into the wall line jack while setting up the Caller ID menu. -
Page 13: Setting Your Locala
ETTING OCAL The telephone uses the programmed area code to determine the number format to display REVIEW button ERASE button OPTION button when a valid Caller ID signal is received and is also used for the Dialback feature. 1. Press the OPTION button. appears. -
Page 14: Setting Your Regional
ETTING EGIONAL REVIEW button Like the Local Area Code, 6 sets of Regional OPTION button Area Codes can also be set. 1. Press the OPTION button. appears. 2. Press either REVIEW ( ) button until REGIONAL AC'S-1 appears. 3. To enter or change the area code, press the OPTION button again. -
Page 15: Setting The Cid D
CID D ETTING THE ISPLAY ANGUAGE REVIEW button This adjustment changes the Caller ID OPTION button prompts to be displayed in English, French, or Spanish. 1. Press the OPTION button. appears. 2. Press either REVIEW ( ) button until SELECT LANGUAGE appears. 3. -
Page 16: One Or
ETTING THE ONE OR ULSE IALING REVIEW button 1. Press the OPTION button. SET OPTION button appears. 2. Press either REVIEW ( ) button until T/P DIAL MODE appears. 3. To enter and change the dial mode, press the OPTION button. The display shows the current setting. -
Page 17: Aller Id Features
ID F ALLER EATURES UMMARY CREEN REVIEW button OPTION button The summary screen shows the current time, date, and number of new calls to be reviewed. It is displayed until the REVIEW or OPTION buttons are pressed or a Caller ID record is received. -
Page 18: Reviewing Callr
EVIEWING ECORDS • Press the REVIEW button to scroll through the call records from the most REVIEW button ERASE button OPTION button recent to the oldest. • When all of the messages have been viewed, START/END appears in the display. ELETING ECORDS •... -
Page 19: I F You Programmed
ROGRAMMED OCAL ODE OR EGIONAL ODE IN REVIEW button DIAL button 1. Use either REVIEW ( ) button to display the number you want to dial. • If you see a number with 7 digits (i.e. 555-1234), then the call was received from within your area code. -
Page 20: I F You Did Notp
3. Press the DIAL button and the display shows PICKUP PHONE . A 10 second timer will appear in the upper right corner of the REVIEW button display and count down time until the unit DIAL button returns to the Caller ID records. •...