New Holland P2080 Service Manual
  1. Manuals
  2. Brands
  3. New Holland Manuals
  4. Drill
  5. P2080
  6. Service manual

New Holland P2080 Service Manual

Disk drill
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
P2080 / P2085
Disk Drill
Part number 47648338
2
edition English
nd
June 2014
Replaces part number 47484215

Advertisement

Table of Contents
loading

Related Manuals for New Holland P2080

Summary of Contents for New Holland P2080

  • Page 1 SERVICE MANUAL P2080 / P2085 Disk Drill Part number 47648338 edition English June 2014 Replaces part number 47484215...
  • Page 2 Contents INTRODUCTION Front axle system ............... 25 [25.400] Non-powered front axle ............25.1 Rear axle system................
  • Page 3 [77.904] Air distribution system............. . 77.4 47648338 18/06/2014 Find manuals at https://best-manuals.com...
  • Page 4 47648338 18/06/2014 Find manuals at https://best-manuals.com...
  • Page 5 INTRODUCTION 47648338 18/06/2014 Find manuals at https://best-manuals.com...

  • Page 6: Table Of Contents

    Contents INTRODUCTION Foreword ..................3 Safety rules .

  • Page 7: Foreword

    INTRODUCTION Foreword Technical information This information in this manual has been structured using a unique coding environment. This is the way in which technical information is created, stored, and retrieved in the Technical Information Database. The coding has aligned locations with the warranty system. All hydraulic information is now in Section 35.

  • Page 8: Safety Rules

    INTRODUCTION Safety rules Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual and on machine safety signs, you will find the signal words DANGER, WARNING, and CAU- TION followed by special instructions.

  • Page 9: Safety Rules

    INTRODUCTION Safety rules WARNING Chemical hazard! Wear protective clothing and a face shield when working with chemicals. Do not allow chemicals to contact skin or eyes. Always follow the chemical manufacturer's instructions. Failure to comply could result in death or serious injury. W0052A WARNING Unexpected machine movement!
  • Page 10 INTRODUCTION Make sure all guards, shields and handrails are in good condition and properly installed before operating machine. Never operate the machine with shields removed. Always close access doors or panels before operating the machine. Dirty or slippery steps, ladders, walkways and platforms can cause falls. Make sure these surfaces remain clean and clear of debris.
  • Page 11 INTRODUCTION When welding follow the instructions in the manual. Always disconnect battery before welding on machine. Always wash your hands after handling battery components. Wheels and tires Make sure tires are correctly inflated. Do not exceed recommended load or pressure. Follow instruction in the manual for proper tire inflation.
  • Page 12 INTRODUCTION Make sure the fire extinguisher(s) is maintained and serviced according to the manufacturer’s instructions. At least once each day and at the end of the day remove all trash and debris from the machine especially around hot components such as engine, transmission, exhaust, battery, etc. More frequent cleaning of your machine may be necessary depending on the operating environment and conditions.
  • Page 13 INTRODUCTION Hazardous chemicals If you are exposed to or come in contact with hazardous chemicals you can be seriously injured. The fluids, lubricants, paints, adhesives, coolant, etc. required for the function of your machine can be hazardous. They may be attractive and harmful to domestic animals as well as humans.
  • Page 14 INTRODUCTION Maintain a three‐point contact with steps, ladders and handholds. Never mount or dismount from a moving machine. Working at heights When the normal use and maintenance of the machine requires working at heights: Correctly use installed steps, ladders and railings. Never use ladders, steps or railings while the machine is moving. Do not stand on surfaces which are not designed as steps or platforms.

  • Page 15: Hand Signals

    INTRODUCTION Hand signals It is often necessary to communicate using hand signals in agricultural operations when noise or distance inhibit communication by voice. The ASAE S351 standard illustrates these hand signals, which provide an easy means of communication, particularly in the interest of safety. MOVE OUT, TAKE OFF - COME TO ME - Raise the THIS FAR TO GO - Place...

  • Page 16: Safety Signs - Disk Drill

    When a safety sign displays this symbol, refer to the appropriate page of the operator’s manual. NOTE: New decals are available from your NEW HOLLAND dealer. 9.1 m (30 ft) and 12.2 m (40 ft) drills...
  • Page 17 INTRODUCTION WARNING Falling object hazard! Loss of hydraulic pressure or movement of a control can cause raised equipment to fall. Never work under an implement supported only by the hydraulic system. Always use the frame locks to service the drill in the raised position. Failure to comply will result in death or serious injury.
  • Page 18 INTRODUCTION WARNING Falling object hazard! Loss of hydraulic pressure or movement of a control can cause raised equipment to fall. Never work under an implement supported only by the hydraulic system. Always use the frame locks to service the drill in the raised position. Failure to comply will result in death or serious injury.
  • Page 19 INTRODUCTION WARNING Do not operate on steep slopes. Failure to comply will result in death or serious injury. Quantity: 1 English: 47405862 47405862A On hitch (3). SAIL12SE00573AA DANGER Electrocution hazard! Contact with overhead power lines can cause severe electrical burns or death from electrocution. Make sure there is enough clearance between equipment and overhead power lines.
  • Page 20 INTRODUCTION 9.1 m (30 ft) only WARNING Crushing hazard! Always use the wing lock pins when working underneath the wings, or when leaving the machine wings up for any extended length of time. Failure to comply could result in death or serious injury.
  • Page 21 INTRODUCTION DANGER Crushing hazard! Stay clear of the implement when the wings are folded or unfolded. Hydraulic or mechanical failure may cause rapid uncontrolled falling of the wings. Failure to comply will result in death or serious injury. Quantity: 2 English: 8459991 84599919A On frame near wing hinge (7).
  • Page 22 INTRODUCTION 15.2 m (50 ft) and 18.3 m (60 ft) drills SAIL13SE00490FA 47648338 18/06/2014...
  • Page 23 INTRODUCTION WARNING Falling object hazard! Loss of hydraulic pressure or movement of a control can cause raised equipment to fall. Never work under an implement supported only by the hydraulic system. Always use the frame locks to service the drill in the raised position. Failure to comply will result in death or serious injury.
  • Page 24 INTRODUCTION WARNING Falling object hazard! Loss of hydraulic pressure or movement of a control can cause raised equipment to fall. Never work under an implement supported only by the hydraulic system. Always use the frame locks to service the drill in the raised position. Failure to comply will result in death or serious injury.
  • Page 25 INTRODUCTION WARNING Loss of control hazard! DO NOT exceed 32 km/h (20 mph) when towing the machine. Failure to comply will result in death or serious injury. Quantity: 1 English: 4740373 47403730A On hitch (2). SAIL12SE00573AA WARNING Do not operate on steep slopes. Failure to comply will result in death or serious injury.
  • Page 26 INTRODUCTION DANGER Electrocution hazard! Contact with overhead power lines can cause severe electrical burns or death from electrocution. Make sure there is enough clearance between equipment and overhead power lines. Failure to comply will result in death or serious injury. Quantity: 1 English: 47405863 47405863...
  • Page 27 INTRODUCTION DANGER Crushing hazard! Stay clear of the implement when the wings are folded or unfolded. Hydraulic or mechanical failure may cause rapid uncontrolled falling of the wings. Failure to comply will result in death or serious injury. Quantity: 4 English: 8459991 84599919A On wing cylinders (6).

  • Page 28: Safety Signs - Disk Drill With Mounted Tank

    When a safety sign displays this symbol, refer to the appropriate page of the operator’s manual. NOTE: New decals are available from your NEW HOLLAND dealer. 47648338 18/06/2014...
  • Page 29 INTRODUCTION SAIL14SE00089GA 47648338 18/06/2014...
  • Page 30 INTRODUCTION CAUTION Avoid possible hearing loss! The machine operator must wear hearing protection. Failure to comply could result in minor or moderate injury. Quantity: 1 English: 47405861 47405861A On tank platform near ladder (1). SAIL12SE00574AA 47648338 18/06/2014...
  • Page 31 INTRODUCTION WARNING Falling object hazard! Loss of hydraulic pressure or movement of a control can cause raised equipment to fall. Never work under an implement supported only by the hydraulic system. Always use the frame locks to service the drill in the raised position. Failure to comply could result in death or serious injury.
  • Page 32 INTRODUCTION WARNING Loss of control hazard! DO NOT exceed 32 km/h (20 mph) when towing the machine. Failure to comply could result in death or serious injury. Quantity: 1 English: 4740373 47403730A On hitch (3). SAIL12SE00573AA WARNING Do not operate on steep slopes. Failure to comply could result in death or serious injury.
  • Page 33 INTRODUCTION DANGER Electrocution hazard! Contact with overhead power lines can cause severe electrical burns or death from electrocution. Make sure there is enough clearance between equipment and overhead power lines. Failure to comply will result in death or serious injury. Quantity: 1 English: 47405863 47405863...
  • Page 34 INTRODUCTION WARNING Chemical hazard! Wear a respirator and any other protective equipment specified by the seed supplier and/or seed treatment supplier. Expect chemical residue, dust, and fumes during clean out. Failure to comply could result in death or serious injury. Quantity: 1 English: 47405860 47405860A...
  • Page 35 INTRODUCTION DANGER Crushing hazard! Stay clear of the implement when the wings are folded or unfolded. Hydraulic or mechanical failure may cause rapid uncontrolled falling of the wings. Failure to comply will result in death or serious injury. Quantity: 6 English: 8459991 84599919A On frame near wing hinge (9).
  • Page 36 INTRODUCTION CAUTION Do not ride on machine. Do not stand on tank Failure to comply could result in minor or moderate injury. Quantity: 1 English: 84004732 84004732A On tank platform near ladder (10). SAIL12SE00574AA NOTICE Fan Motor Case Drain Line Failure to connect this line to a case drain port with less than 170 kPa (26 psi) back pressure will result in motor failure and the voiding of warranty.

  • Page 37: Safety Rules - Ecology And The Environment

    • Do not open the air-conditioning system yourself. It contains gases that should not be released into the atmosphere. Your NEW HOLLAND dealer or air conditioning specialist has a special extractor for this purpose and will have to recharge the system properly.

  • Page 38: Basic Instructions - Important Notice Regarding Equipment Servicing

    Some information could not be updated due to modifications of a technical or commercial type, or changes to the laws and regulations of different countries. In case of questions, refer to your NEW HOLLAND Sales and Service Networks. 47648338 18/06/2014...

  • Page 39: Torque

    INTRODUCTION Torque BOLT TORQUE INFORMATION 1. Fasteners should be replaced with the same or higher grade fasteners. If higher grade fasteners are used, these should only be tightened to the strength of the original. 2. Make sure the fastener's threads are clean and that thread engagement is started. This will prevent them from failing when being tightened.
  • Page 40 INTRODUCTION GRADE 2* GRADE 5, 5.1 or 5.2 GRADE 8 or 8.2 GRADE L9 (Alloy) SIZE Dry ** Lubricated ** Dry** Lubricated ** Dry** Lubricated ** Head 3/4 UNF 237 Nm 176 Nm 353 Nm 271 Nm 515 Nm 380 Nm 359 Nm 393 Nm 175 lb ft...

  • Page 41: Torque - Hydraulic Tubes And Fittings

    This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...

This manual is also suitable for:

P2085

Table of Contents