Exmark Quest 126-7510 Manual
Exmark Quest 126-7510 Manual

Exmark Quest 126-7510 Manual

50 inch bagger

Advertisement

Quick Links

50 Inch Bagger
Quest
®
Model No. 126-7510—Serial No. 400000000 and Up
This product contains a chemical or chemicals known to the State of California
Important:
This kit requires the simultaneous installation of other kits to function properly. Lever steer
units require a front weight kit and a mounting kit. Steering wheel units require a mounting kit. Contact
your Authorized Service Dealer to obtain the corresponding necessary parts.

Introduction

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.
Whenever you need service, genuine parts, or
additional information, contact an Authorized Service
Dealer or Customer Service and have the model
and serial numbers of your product
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.
1. Model and serial number location
© 2017—Exmark Mfg. Co., Inc.
Industrial Park Box 808
Beatrice, NE 68310
Proposition 65 Warning
to cause cancer, birth defects, or reproductive harm.
ready.Figure 1
Figure 1
www.Exmark.com
WARNING
CALIFORNIA
Model No.
Serial No.
This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(Figure
2), which signals a hazard that may cause
serious injury or death if you do not follow the
recommended precautions.
This manual uses two words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
g207309
Form No. 4503-386 Rev A
Operator's Manual
Figure 2
Safety alert symbol
Original Instructions (EN)
All Rights Reserved *4503-386* A
Printed in the USA.
g000502

Advertisement

Table of Contents
loading

Summary of Contents for Exmark Quest 126-7510

  • Page 1: Introduction

    Note emphasizes general information worthy of special attention. g207309 Figure 1 1. Model and serial number location © 2017—Exmark Mfg. Co., Inc. www.Exmark.com Original Instructions (EN) All Rights Reserved *4503-386* A Industrial Park Box 808 Printed in the USA.
  • Page 2: Table Of Contents

    Contents Introduction ............... 1 Safety ............... 3 Towing Safety ............. 3 Safety and Instructional Decals ......5 Setup ................ 6 1 Preparing the Machine........7 2 Installing the Weight......... 7 3 Installing the Attachment Mount ....... 9 4 Assembling the Bagger Top ......12 5 Installing the Bagger Top........
  • Page 3: Safety

    Safety • Follow the manufacturer's recommendations for adding or removing wheel weights or counterweights to improve stability. WARNING • Do not use a grass catcher on steep slopes. A heavy grass catcher could cause loss of control CALIFORNIA or overturn the machine. Proposition 65 Warning •...
  • Page 4 • On slopes, the weight of the towed equipment may cause loss of traction and loss of control. Reduce towed weight and slow down. • Stopping distance increases with the weight of the towed load. Travel slowly and allow extra distance to stop.
  • Page 5: Safety And Instructional Decals

    Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal131-4036 131-4036 1. The maximum drawbar 2. Read the Operator's decal110-6691 pull is 36 kg (80 lb).
  • Page 6: Setup

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Bolt (3/8 x 1-1/4 inches) Locknut (3/8 inch) Weight mounting bracket, left Weight mounting bracket, right Washers Install the weight.
  • Page 7: Preparing The Machine

    Note: Determine the left and right sides of the CAUTION machine from the normal operating position. The bagger changes the weight distribution of the machine. Operating the machine without the front weights may cause an unstable condition which could result in a loss of control.
  • Page 8 3. Locate the left and right weight-mounting brackets in loose parts. 4. Install the left bracket to the under side of the frame using 2 bolts (3/8 x 1-1/4 inches), 2 washers and 2 locknuts (3/8 inch) (Figure Note: One locknut is from loose parts and the other is used from earlier removal.
  • Page 9 Note: Make sure the bracket is centered on the frame. 7. Secure the weight bracket with 2 bolts (3/8 x 1 inch) and 2 locknuts (3/8 inch) (Figure G014879 g014879 Figure 8 1. Locknut (3/8 inch) 4. Bolt (3/8 x 1 inch) 2.
  • Page 10: Installing The Attachment Mount

    using two bolts (5/16 x 1 inch) and two locknuts (5/16 inch). Installing the Attachment Mount Parts needed for this procedure: Stabilizer bracket (For 2015 and newer models) Carriage bolt (5/16 x 3/4 inch) Locknut (5/16 inch) Self-tapping screw (5/16 x 3/4 inch) Bolt (5/16 x 1 inch) Pivot frame Hairpin cotter...
  • Page 11 For 2011 through 2014 Models Only Note: The stabilizer bracket is not used on 2011 through 2014 models. Note: For 2011 through 2014 models, the rear-engine guard is optional for this bagger. 1. Install the pivot frame to the machine frame. Secure the pivot frame to the machine frame using two bolts (5/16 x 1 inch) and two locknuts (5/16 inch).
  • Page 12: Assembling The Bagger Top

    g030499 g030499 Figure 18 Left side shown 1. Pivot-frame hole 4. Support rod g030497 2. Washer 5. Keyed slot (existing) g030497 3. Hairpin cotter 6. Bent, flared end of support Figure 16 1. Self-tapping screw (5/16 x 3/4 inch) 5. Insert the bent ends of the rod into the 2.
  • Page 13: Installing The Bagger Top

    Installing the Bagger Top Parts needed for this procedure: Hood rod Hairpin cotter pin Grass Bag Upper bagger tube Procedure 1. Install the hood rod to the bagger frame with a hairpin cotter pin. Install the hairpin cotter pin from the bottom. g032708 Figure 20 G005666...
  • Page 14 g028327 g032709 g028327 Figure 21 Figure 22 1. Bagger top 4. Bracket, bagger top 1. Bag 3. Retaining bracket 2. Bagger frame 5. Key 2. Bagger frame 4. Bag frame hook 3. Key hole 6. Post 4. Lower the bagger top onto the bag. 3.
  • Page 15: Installing The Chute

    g018363 g018363 Figure 24 1. Rubber hood latch 3. Latched position 2. Hood rod end 7. Push the hood latch over the end of the hood rod as shown in Figure g017834 g017834 Figure 25 1. Flange nuts Installing the Chute 3.
  • Page 16: Attaching The Discharge Tube

    g017842 g017842 Figure 29 1. Latch 2. Hole in the mower deck stiffener g018310 g018310 Figure 27 1. Knob 3. Chute 2. Flat washer (5/16 inch) Attaching the Discharge 5. Hook the flexible latch on the chute to the Tube retaining clasp welded on the mower deck to the rear of the opening (Figure...
  • Page 17: Operation

    Operation G010641 Note: Determine the left and right sides of the machine from the normal operating position. Note: Overall width of unit with bagger: 58.7 inches (149 cm). WARNING To avoid personal injury, follow these procedures: • Become familiar with all operating and safety instructions in the Operator's Manual for the mower before using this attachment.
  • Page 18: Clearing Obstructions From The Bagger

    1. Park the machine on a level surface and disengage the blade control switch. 2. Stop the engine, remove the key, set the parking brake and wait for all moving parts to stop before leaving the operating position. 3. Open (raise) the bagger top (Figure 31).
  • Page 19: Removing The Bagger

    Removing the Bagger Transporting CAUTION Transporting the Machine Failing to remove the front bagger weights Use a heavy-duty trailer or truck to transport the from lever steer models and operating the machine. Ensure that the trailer or truck has all machine without the bagger attachment may necessary brakes, lighting, and marking as required cause an unstable condition which could...
  • Page 20: Operating Tips

    g027995 Figure 35 1. Back up ramps 2. Drive forward down ramps Important: Do not use narrow individual ramps for each side of the machine. Ensure the ramp is long enough so that the angle with the ground does not exceed 15 degrees (Figure 36).
  • Page 21 Cutting Height happens, the discharge tube and chute may plug. To avoid plugging the bagging system, mow the grass Do not set the mower cutting height too low because at a high height of cut, then lower the mower to your long grass surrounding the mower can prevent air normal cutting height and repeat the bagging process.
  • Page 22: Maintenance

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Inspect the bagger After the first 10 hours • Clean the bagger Before each use or daily •...
  • Page 23: Inspecting The Mower Blades

    Inspecting the Mower Storage Blades Storing the Bagger Inspect the mower blades regularly and whenever a Attachment blade strikes a foreign object. If the blades are badly worn or damaged, install new 1. Clean the bagger attachment; refer to Cleaning blades.

Table of Contents