Explanation of symbols ............................6 NCR Orderman Base Station4 ..................7 Overview ..............................7 Product description ..........................8 NCR Orderman Base Station4 Features ....................8 Installation of the NCR Orderman Base Station4 ............9 Preparation .............................. 9 3.1.1 Installing the antenna ............................9 3.1.2 Uninstalling the antenna ............................
General information General information This manual is intended for use with the NCR Orderman Base Station4 (OMB4). The “NCR Orderman Base Station4” is used for radio transmission, and forms the connecting link between the Orderman handheld radio units and the PC-based POS systems. In this manual, we refer to the “NCR Orderman Base Station4”...
User Manual V01.10 General information 1.2.2 Serial number The serial number is used to uniquely identify the unit. The serial number is located on the model plate. Fig. 2: Serial number Serial number Orderman GmbH (Part of NCR Corporation)
Notes are highlighted by horizontal lines above and below the text. Tips Tips describe non-binding recommendations. Tips are highlighted by horizontal lines above and below the text. Orderman GmbH (Part of NCR Corporation)
Product description The NCR Orderman Base Station4 is specially designed to connect with an Orderman secure radio (OSR). The NCR Orderman Base Station4 can be installed in standing position, hanging from a wall or ceiling, or suspended in a false ceiling.
NCR Orderman Base Station4 User Manual V01.10 Installation of the NCR Orderman Base Station4 Installation of the NCR Orderman Base Station4 Preparation 3.1.1 Installing the antenna The antenna is screwed into the housing with a right-hand thread. Turn the antenna in a clockwise direction (using finger force) into the housing until it hits the end stop.
NCR Orderman Base Station4 User Manual V01.10 Installation of the NCR Orderman Base Station4 3.1.3 Removing/replacing the housing cover For connection, i.e. for installation, you must remove the housing cover. It is not necessary to remove the antenna. 3.1.3.1 Removing the housing cover ...
NCR Orderman Base Station4 User Manual V01.10 Installation of the NCR Orderman Base Station4 3.1.4 Uninstalling/installing the mounting plate 3.1.4.1 Uninstalling the mounting plate To remove the mounting plate from the housing, release the two retaining clips by pressing them away from the housing.
Installation of the NCR Orderman Base Station4 Setup The NCR Orderman Base Station4 is designed to be set up indoors. It can be positioned standing, on the wall, overhead (ceiling mount) or suspended in a false ceiling. For optimal radio performance, avoid installation close to metal objects.
NCR Orderman Base Station4 User Manual V01.10 Installation of the NCR Orderman Base Station4 3.2.1 Standing position Rubber nubs on the underside of the mounting plate increase the stability. Fig. 10: Standing position Rubber nubs Orderman GmbH (Part of NCR Corporation)
NCR Orderman Base Station4 User Manual V01.10 Installation of the NCR Orderman Base Station4 3.2.2 Wall/ceiling installation For wall/ceiling installation, the mounting plate has 2 mount holes. As the fastening means for concrete masonry Orderman recommends a 6 x 30 mm wall plug and a 4 x 35 mm universal screw with countersunk head.
Page 15
NCR Orderman Base Station4 User Manual V01.10 Installation of the NCR Orderman Base Station4 Note: For the wall and ceiling installation, the mounting surface must be level. For a wall mount, we recommend you install the mounting plate with the cable outlet point downward.
NCR Orderman Base Station4 User Manual V01.10 Installation of the NCR Orderman Base Station4 3.2.3 Installation in a false ceiling For installation in a false ceiling, clips are provided to compensate for the wedge profile of the housing. The following steps must be followed: ...
Installation of the NCR Orderman Base Station4 Cabling The NCR Orderman Base Station4 can only be connected with an Ethernet network. Two RJ45 ports are located on the top of the housing. The port labeled PoE can also be used for power supply via the network (accessory required).
Operation with power supply unit Comply with the operating temperature range (ambient temperature) for Note: the power supply unit. Use only the original power supply unit for the NCR Orderman Base Station4. Operation with Power over Ethernet (network-powered) There are two options for using Power over Ethernet: ...
Page 19
NCR Orderman Base Station4 User Manual V01.10 Operation Fig. 18: Light ring Light ring Orderman GmbH (Part of NCR Corporation)
Wipe the surface with a damp, soft cloth. Do not use abrasive agents or cloths with a rough surface. Clean the ports: Never clean the sockets with compressed air or pointed objects! Note: Never use alcohol or corrosive liquids to clean the Orderman units. Orderman GmbH (Part of NCR Corporation)
Max. 1dBm (ERP) for all countries Power over Ethernet (PoE) IEEE 802.3at-2009 Type 1 (IEEE 802.3af-2003 compatible) IEEE802.3-2008IEEE802.3af-2008) Protection type IPX4 Dimensions L/W/H mm 160x160x50 without antenna 160x160x190 with antenna Weight 750 grams *see country list Orderman GmbH (Part of NCR Corporation)
Radio interference from other the radio path devices (baby monitor, handheld radio transmitter, remote control, etc.) NCR Orderman Base Station status indicator Pink There is no network connection Check the OMB4 network cable to the NCR Orderman Base Not connected to network Station4 A OMB4 is not available.
NCR Orderman Base Station4 User Manual V01.10 Troubleshooting Factory reset on the NCR Orderman Basisstation4 Action Time Status Press and hold 2 seconds Reset button for 22 seconds 8 seconds The status indicator lights up blue for 8 seconds 5 seconds...
NCR Orderman Base Station4 User Manual V01.10 Country list Country list The NCR Orderman Base Station4 is available in two different frequency versions. Note: Make sure that the right OMB4 version is installed (see table) to match the country selected. Country...
Radio base station 22 Certifications 4 Orderman contractual partners 4 Serial number 5 Labeling 4 Orderman partner 2 Standards 4 Manufacturer Orderman Secure Radio (OSR) 8 Warranty claims 4 information 4 Product name 4 Orderman GmbH (Part of NCR Corporation)
LED (Light-Emitting Diode) LEDs convert electrical energy into very energy-efficient light. LEDs have a very long life. NCR Orderman Base Station4 (OMB4) The NCR Orderman Base Station4 enables users to connect Orderman handhelds to a host system. Orderman Secure Radio The Orderman secure radio uses the 433MHz or 915MHz, depending on application area.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Manufacturer: NCR Corporation, 2651 Satellite Blvd. Duluth, GA 30096 USA Importer: Orderman GmbH (part of NCR Corporation), Bachstrasse 59, 5023 Salzburg, AUSTRIA Orderman GmbH (Part of NCR Corporation)