Advertisement
Quick Links
Product Name:
ADVBSVGM8
Product Application:
Blind Spot Video Mode: (DIP4 ON)
4 Camera's Front/Back/Left/Right (Automatic Front, Right, Left and Rear Camera) For Blind Spot
detection
1 Reverse Camera (for cars without OE Camera)
1 Front Camera with automatic trigger (for cars with OE Camera)
3 Camera's Front/Right/Left with automatic trigger (for cars with OE Camera) For Blind Spot
detection
Video Mode: (DIP4 OFF)
3 Video inputs (Phone Mirroring, 360 degree system, DVD, TV tuner or any video input) and 1 Reverse
Camera input.
Car Types:
Cadillac SRX, ATS, CTS, 2016(CT6 and XT5) etc. (7", 8" and 10" Cadillac CUE
Systems from 2013 and onwards)
GM/Chevrolet/Opel/Holden Astra, Suburban, Tahoe, 2016(Malibu, Cruze, Lacrosse, Volt etc.)
(7" and 8" Intellilink Systems from 2013 and onwards)
4280741
ADVBSVGM8
Installation Manual
V20170114
Manual Version:
Advertisement
Related Manuals for Advent ADVBSVGM8
Summary of Contents for Advent ADVBSVGM8
- Page 1 V20170114 Manual Version: ADVBSVGM8 Installation Manual Product Name: ADVBSVGM8 Product Application: Blind Spot Video Mode: (DIP4 ON) 4 Camera's Front/Back/Left/Right (Automatic Front, Right, Left and Rear Camera) For Blind Spot detection 1 Reverse Camera (for cars without OE Camera) ...
- Page 2 Optional camera's available. 1. Description: The ADVBSVGM8 camera interface is the latest line of product from Advent. This solution has two working modes. 1. Blind spot video interface mode which enables user to install Front Camera, Reverse Camera, Right Side Camera and Left Side Camera.
- Page 3 Reverse Camera and Guidelines shown on Cadillac CUE 2016. Move according to data from steering wheel position. Only reverse camera can be chosen by selecting the desired Dips if other camera's not needed. Parking Sensor will be displayed with the reverse guidelines and reverse camera.
- Page 4 2. Interface Functions: BSV Mode: The Reverse Camera is automatically triggered when engaging the reverse gear of the car. The front camera is automatically displayed for 5 seconds when user switches out of reverse gear. It will also be displayed for 5 seconds after the turn signals are turned off. (Option to turn off show front camera after turn signals using DIP6) The Right and Left camera's will be triggered with the turn signals and will automatically turn off once turn signals are turned off.
-
Page 5: Installation
3. Installation: Installation of this interface is very easy as it is completely plug and play. There is no need to open the radio to insert any PCB. All the installation is done behind the HMI Unit which on the 2016 models is usually located under the glove box. ... - Page 6 In order to install the interface you will need to open the glove compartment to gain access to the HU/CD unit. Once gaining access you will need to remove the main harness and insert our harness in its place and insert the OE harness into our plug in order to complete the T- Harness.
- Page 7 4. Connection Diagram: Connect LVDS behind the HMI. In place of blue connector Connect Power harness behind HMI Power for all for cameras Front Cam Port Right, Left and Touch Pad for Back Cam Port forced switch Not used...
- Page 8 5. Camera Connection: All cameras will be connected with the green wire. It can provide 12V/3A which is sufficient to supply power for the 3 or 4 cameras. Connect RCA accordingly Power *NOTE: Ground for the camera power should not be connected or noise may be seen on the display. 6.
- Page 9 7. CAN DIP Settings: DIP Down= ON DIP UP= OFF Default Front Camera will be shown after Front Camera will Not be shown DOWN(ON) Turn Signals are triggered and after Turn Signals are triggered. Reverse gear is disengaged. Only Shown after Reverse gear is disengaged.
- Page 10 9. Parameters: Name Parameter Front Cam Video , Reverse Cam video 0.7Vpp with 75 ohm impedance NTSC/PAL/SECAM automatic switch Reverse Control wire >5V will force into camera mode. These wires can tolerate 12V for <10 seconds. Normal Power consumption 4.8W Standby current <...