GE Profile JS998SHSS Specifications

Shave Raised Edge To Clear
30" Min .
31-1/8" Wide Control Panel
Recommended
6" Min.
From Walls
9/16
30" Min .
TM
Acceptable
23-3/16
Electrical
13" Max.
Outlet Area
36
JS998SH/TH/KH/BH – GE Profile ™ 30" Slide-In Electric Range with Trivection ™ Technology
2-1/2
7-1/2
2-1/2
Dimensions (in inches)
30
24
31-1/4
2-7/8"
To Front
Surface Of
Countertop
30" Slide-In Range
Dimensions (in inches)
20-5/8" Door
Clearance
From Front
Surface of
30" Slide-in Elec. Range
Countertop
Aug. 8, 2003 -km
30 Min.
15 Min. 27-1/2
30" Slide-In Range
Dimensions (in inches)
KW Rating
2-1/4
12.8
240V
Maintain
at least 6"
9.6
208V
from nearest
30 Min.
*Wall to front of combustible
6 closed door handle surface.
15 Min.
Breaker Size
on model JSP34.
28" on models
JSP26/JSS26/16.
31-1/2
40 Amps
240V
30
4-1/2
6
40 Amps
208V
Note: Range may be placed with 0" clearance (flush) at the back wall and side walls
5
below countertop if the range side trims above the countertop extend beyond the cabinet
fronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearest
2-1/4
combustible surface.
Acceptable
Electrical
Outlet Area
*Wall to front of
closed door handle
28-1/4*
on model JSP34.
28" on models
45-1/8
JSP26/JSS26/16.
Specification Revised 7/05
220450
Note: Range may be placed with 0" clearance (flush) at the back wall and side walls
below countertop if the range side trims above the countertop extend beyond the cabinet
fronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearest
15" Min.
25
2000_slide_in.eps
Accessory
Backguard
Recommended
30" Slide-in Elec. Range
6" Min.
From Walls
Aug. 8, 2003 -km
A/B
23-3/16
36
Maintain
2-1/2
at least 6"
from nearest
combustible
6 surface.
30
31-1/2
30
4-1/2
6
If you are NOT using the
5
Filler strip or Backguard:
Acceptable
Electrical
Outlet Area
23-3/16
2-7/8"
To Front
28-1/4*
30
Surface Of
30
45-1/8
Countertop
If you are using the
Filler strip or Backguard:
36
25
30
30
Note: Cabinets installed adjacent to slide-in electric ranges must have an
adhesion spec of at least 194°F temperature rating.
Shave Raised Edge To Clear
30" Min . 31-1/8" Wide Control Panel
Note: All 30" Slide-In Ranges conform to U.L. requirements for 0" spacing from range
9/16
to adjacent walls below countertop. To reduce possibility of scorching the side walls
above the countertop when no load is present on burners, it is recommended that a
minimum 6" spacing from adjacent side wall be allowed for possible extended high-
30" Min .
heat element operation.
Acceptable
Electrical
13" Max.
Outlet Area
Receptacle Locations: For all 30" Slide-In Ranges locally approved flexible service
15" Min.
cord or conduit must be used because terminals are not accessible after range
If you are NOT using the
installation. See shaded area in drawing for location of electrical outlet box. Recom-
25
Filler strip or Backguard:
mended outlet locations allow range to be installed directly against rear wall.
Accessory Backguards
23-3/16
(Attaches to the back of range as a backguard when unit is installed in
7-1/2
30" free-standing cutout)
JXS37WW – White
2-1/2
30
JXS37CC – Bisque
JXS37BB – Black/Stainless
If you are using the
Installation Information: Before installing, consult installation instructions
Accessory
Filler strip or Backguard:
Backguard
packed with product for current dimensional data.
36
25
24
31-1/4
30
20-5/8" Door
Clearance
From Front
Surface of
For answers to your Monogram, ® GE Profile ™ or
Countertop
GE ® appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center ® service, 800.626.2000.
27-1/2
A/B
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
Listed by
Underwriters
Laboratories
R