Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
GE Consumer & Industrial
Appliances
Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com
BEFORE YOU BEGIN
STOP
Read these instructions completely and
carefully.
IMPORTANT
– Observe all governing codes
and ordinances.
• Note to Installer – Be sure to leave these
instructions for the consumer and local inspector's
use.
• Note to Consumer – Keep these instructions with
your Owner's Manual for future reference.
• Skill Level – Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills.
Proper installation is the responsibility of
the installer. Product failure due to improper
installation is not covered under the GE
Appliance Warranty. See warranty information.
GSD2000
• Completion Time – 1 to 3 Hours. New installations
require more time than replacement installations.
IMPORTANT
installed to allow for future removal from the
enclosure if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner's Manual for
available custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While
performing installations described in this booklet,
gloves and safety glasses should be worn.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
– The dishwasher MUST be
Advertisement
Table of Contents
Related Manuals for GE GSD1300N
Summary of Contents for GE GSD1300N
-
Page 1: Installation Instructions
GE Consumer & Industrial Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com BEFORE YOU BEGIN STOP Read these instructions completely and carefully. IMPORTANT – Observe all governing codes and ordinances. -
Page 2: Air Gap
PARTS SUPPLIED IN INSTALLATION PACKAGE: Two 8-18 x 5/8" Phillips head wood screws ■ Junction box cover and #10 hex head ■ screw Drain hose (78" long) and hose clamp ■ Cord protector (Power Cord Models Only) ■ Conversion leads (Power Cord Models Only) ■... -
Page 3: Prepare Dishwasher Enclosure
fit. Refer to Figure A • For a corner installation, allow 2" minimum clearance between the dishwasher and the adjacent wall. • Provide at least 27" in front of the dishwasher to allow the dishwasher door to open fully. Refer to Figure B ��������������... -
Page 4: Prepare Drain Plumbing
Special consideration for a dishwasher installed on a pedestal lf the dishwasher is installed on an elevated platform, a high drain loop of at least 32" above the platform must be provided in addition to the air gap requirement determined above. -
Page 5: Prepare Electrical Wiring
Protector 1-1/2" Maximum (Provided with Power Cord Models Only) Electrical Connection to Dishwasher Electrical connection is on the right front of dishwasher. • For permanent connections, the cable must be routed as shown in Figure E. The cable must extend a minimum of 24"... - Page 6 • The water connection is on the left side of the dishwasher. Install the hot water inlet line, using 3/8" or larger copper tubing. Route the line as shown in Figure F and extend forward at least 19"...
-
Page 7: Dishwasher Installation
• Conversion leads (Factory-equipped Power Cord Models Only) –Appendix STEP 2: CHECK DOOR BALANCE • With the dishwasher on the wood base, check the door balance by opening and closing the door. • The door is properly balanced if it gently drops from a 1/2 open position and does not rise from the full open position. -
Page 8: Step 5: Install Power Cord
The power cord and connections must comply with the National Electrical Code, Section 422 and/ or local codes and ordinances. Maximum power cord length is 6 feet. Power Cord Kit WX09X70910, available for purchase from an authorized GE Appliance Dealer, meets these requirements. Ground Junction... - Page 9 Dishwasher Installation is approximately 78" long. If a longer hose is needed, a 10 foot long hose may be purchased from an authorized GE appliance dealer. The 10 foot long hose is part number GPF10S. Do not use Hose Stop...
-
Page 10: Step 11: Slide Dishwasher Into Cabinet
3/4" Check Level Front-to-Back Check Level Figure R Side-to-Side • Adjust the level of the dishwasher by individually turning the four legs on the bottom of the 06F-1847Da dishwasher as illustrated in Figure S. Turn Legs to Adjust Figure S •... -
Page 11: Step 14: Connect Water Supply
Figure T Tip: Avoid unnecessary service charges for leaks 06F-1847D or control panel damage. Make sure the dishwasher is centered in the cabinet and the door opens and closes freely without hitting the adjacent cabinets. Drive mounting screws straight and flush. -
Page 12: Step 15: Connect Drain Line
������� IMPORTANT Figure W line to a disposer, check to be sure that the drain plug has been removed. Dishwasher will not drain if plug is left in place. Tip: Avoid unnecessary service call charges for a no drain complaint Make sure any excess drain hose has been pulled through the cabinet opening. -
Page 13: Step 16: Connect Power Supply
Steps 13 and 14 Pull lower rack about halfway out. Check to be ■ sure it does not roll back into dishwasher or further out. If it does, re-level the dishwasher. See Step 12 Check to be sure control panel does not touch ■... - Page 14 2 4 8 EATED ELAY TART (2 T OURS IMES ESET Check for leaks under the dishwasher. If a leak is ■ Hot Start Option S ta r t S ta r t Delay (HRS) Light W ash Pla t e W armer (Heated D r y On) Check for leaks around the door.
- Page 15 • Align the access panel to the dishwasher. • Select the two 8-32 x 1/4" machine thread screws just removed and insert them through the top holes in the access panel and into the dishwasher frame. • Tighten these screws.
- Page 16 EQUIPPED POWER CORD TO A PERMANENT CONNECTION This procedure requires the conversion leads set aside in Step 1. • Make sure the power cord for the dishwasher is unplugged from the wall outlet. • Remove screw from junction box cover and remove cover if present.