Advertisement
GRUNDIG E2000 Series
Channel Setting Cont'd
buttons (4).
• To store the settings and quit service mode,
press UPDATE button (7).
selected is highlighted). Use the V+, V-
• To quit service mode without storing, press the
buttons (4) to modify settings (eg. programme
TV button (18).
number, channel number, etc.)
• To go from one page of the service menu to
• Select the line Programme, type the pro-
another, press the MENU button (5).
gramme number using the numbered buttons
(2) or the P+, Pbuttons (3).
Particularity: the selection of the G2 function
• To modify the standard, if necessary, for sets
has the effect of masking page 1 of the service
with this function. Select the line STANDARD,
mode, with only G2 remaining on the screen.
use the buttons V+, V- (4) to change the
The contrast value (maximum) and brightness
reception standard : LL' for French channels,
(minimum) are adjusted automatically. Pressing
BG, I/I' for other European channels.
on the P+ or P- buttons (3), to choose another
• Select the line Channel, if the channel you are
function, will display page 1 again.
looking for is brodcast in the Cable Networks
standard, press the GREEN button (13), the
Explanations of Functions
display will change from C-- to S-- (the same
button allows you to come back to the C--
Note: before changing IC502, note the values
display): C for hertz reception, S for satellite
and selections defined in service mode (pages 1
reception.
and 2) in order to be able to program them back
• Type the channel number using the numbered
in as soon as the IC502 replacement has been
buttons (2), as a two digit number (eg. C2-
carried out.
first), then the second digit (eg. C25). For
channels between 0 and 9 type 0 instead of
R, G, B settings: depending on the type of
the first digit (eg. S05).
cathode-ray tube the values defined are as
• If you do not know the channels in your area,
follows:
it is possible to do an automatic search as
follows:
Hold down the V+ button (4), the channel search
R
is carried out step by step in ascending order or
G
in descending order with the V- button (4). The
B
search stops as soon as a transmitter is found.
If the channel is not what you want, start the
search again as before.
Note: the UHF, VHF1 and VHF3 bands are
automatically explored (depending on the
country).
• Store by pressing the BLUE button (15). The
<<blue>> block (dialogue line) will display OK
for about one second (to signal storing)
before displaying STORE again. Proceed in
the same way for all the channels.
Fine tuning
The channel is automatically tuned to its
optimum setting, although certain local condi-
tions of reception may make however a
deviation necessary. The channel must then be
fine tuned. The fine tuning is made by succes-
sive jumps (±63 steps) of 62.5 Khz each.
• Select the line FINE TUNING using the P+ or
P- buttons (3).
• Change the setting using the buttons V- (4)
(negative fine tuning) or V+ (4) (positive fine
tuning).
• Store as before.
Service Mode
The service mode is specially designed for the
maintenance of the television set. It allows the
main geometry, white balance, AGC, G2 and
frame configuration adjustments, etc. to be
carned out.
To activate service mode, hold down the buttons
P+ and P- [3] (on the front of the set), then
switch on the television set by pressing the on/
off button [1], until the picture appears. The
service menu appears on the screen.
In order to select the different functions and to
modify the settings, the use of the remote
control is essential.
The function Vert lin is automatically selected.
• To choose a function in service mode, press
the P+ or P- buttons (3).
• To modify the setting, press the V+ or V-
Page 1
Panasonic
Philips
66 EAK 071X11
66 ECF 50X05
53 Steps
50 Steps
38 Steps
39 Steps
38 Steps
33 Steps
Dolby Amp RC Diagram
Page 2 (Press the MENU button once).
(
) Settings defined in the factory.
Amp RL Diagram
Advertisement
