Equipment Description; Assembly; Features And Controls; Operation - Briggs & Stratton 020595-03 Manual

Equipment Description

Read this manual carefully and become familiar
with pressure washer. Know its applications, its
limitations, and any hazards involved. Save
these original instructions for future reference.
This pressure washer operates at a max of 23.4 MPa
(3,400 PSI or 234 BAR) and a flow rate of up to 10.6
liters (2.8 gallons) per minute. This high quality residential
system features 25.4 cm (10") wheels, axial cam pump
with stainless steel pistons, automatic cool down system,
detergent siphoning system, quick connect spray tips,
heavy duty 9.1 m (30') hose, and more.
Every effort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
NOTICE If you have questions about intended use, ask
dealer or contact qualified service center. NEVER operate
units with broken or missing parts, or without protective
housing or covers. DO NOT by-pass any safety device
on this machine. DO NOT modify pressure washer in any
way. This equipment is designed to be used with Briggs &
Stratton authorized parts ONLY.
Transporting
When transporting equipment with a vehicle or trailer,
EMPTY fuel tank or turn fuel shutoff valve, if equipped, to
OFF (0) position. DO NOT tip engine or equipment at angle
which causes fuel to spill.

Assembly

Attach Handle and Accessory Tray Figure
3 4
1. Place handle (1, A) onto supports (1, B) and align
holes (1, C).
2. Insert carriage bolts (2, A) through holes from back of
unit, attach with plastic knob (2, B) and tighten.
3. Place accessory tray (3, A) over holes (3, B) on
handle and push tree clips (3, C) into holes.
4. Insert spray gun holder wireform (4, A) through hole on left
side of handle, attach with plastic knob (4, B) and tighten.
Features and Controls Figure
A Spray Gun
B Accessory Tray
C High Pressure Hose
D Nozzle Extension with
Quick Connect
E Choke Lever
F Air Filter
G Pump
H Automatic Cool Down
System
J High Pressure Outlet
K Water Inlet
1 2
5
L Detergent Siphoning Tube
M Oil Drain
N Oil Fill
P Identification Label
R Recoil Starter
S Throttle Lever
T Fuel Shut-Off Valve
U Fuel Tank
V Warning Tag
W Spray Tips

Operation

Oil
Oil Recommendations Figure
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,
SG, SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
* Below 4°C (40°F) the use of SAE 30 will result in hard starting.
** Above 27°C (80°F) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
Checking/Adding Engine Oil Figure
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure pressure washer is on a level surface.
2. Clean area around oil fill (A) and remove oil fill cap.
3. Verify oil is at the point of overflowing (B) at oil fill opening.
4. If needed, slowly pour oil into oil fill opening to the
point of overflowing at oil fill.
5. Replace and tighten oil fill cap.
NOTICE DO NOT attempt to crank or start engine before
before it has been properly serviced with recommended oil.
This could result in an engine failure.
CAUTION Avoid prolonged or repeated skin contact with
used motor oil. Used motor oil has been shown to cause
skin cancer in certain laboratory animals. Thoroughly wash
exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON'T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
Add Fuel
Figure
9
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). For high
altitude use, see High Altitude.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE Use of unapproved fuels could damage
pressure washer and voids warranty. DO NOT use
unapproved gasoline such as E15 and E85. DO NOT mix
oil in gasoline or modify engine to run on alternate fuels.
To protect the fuel system from gum formation, mix in a
fuel stabilizer when adding fuel. See Storage. All fuel is
not the same. If you experience starting or performance
problems after using fuel, switch to a different fuel provider
or change brands. This engine is certified to operate on
gasoline. The emission control system for this engine is
EM (Engine Modifications).
7
8
5