TABLE OF CONTENTS PAGE PAGE 1 Safety Precaution -------------------------------------------------3 1.1. General Guidelines ----------------------------------------3 1.2. Leakage Current Cold Check ---------------------------3 1.3. Leakage Current Hot Check (See Figure 1.)--------3 1.4. How to Discharge the Capacitor on Flash Top PCB------------------------------------------------------------4 2 Warning --------------------------------------------------------------5 2.1.
1 Safety Precaution 1.1. General Guidelines 1.3. Leakage Current Hot Check 1. IMPORTANT SAFETY NOTICE (See Figure 1.) There are special components used in this equipment 1. Plug the AC cord directly into the AC outlet. Do not use which are important for safety. These parts are marked by an isolation transformer for this check.
1.4. How to Discharge the Capacitor on Flash Top PCB CAUTION: 1. Be sure to discharge the capacitor on FLASH TOP PCB. 2. Be careful of the high voltage circuit on FLASH TOP PCB when servicing. [Discharging Procedure] 1. Refer to the disassemble procedure and Remove the necessary parts/unit. 2.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD).
2.2. How to Replace the Lithium Battery 2.2.1. Replacement Procedure 1. Remove the MAIN PCB. (Refer to Disassembly Procedures.) 2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B9101” at foil side of Main PCB) and remove the Lithium battery together with electric lead terminal.
3 Service Navigation 3.1. Introduction This service manual contains technical information, which allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual. 3.2.
3.4. How to Define the Model Suffix (NTSC or PAL model) There are six kinds of DMC-LZ10, regardless of the colours. • a) DMC-LZ10 (Japan domestic model) • b) DMC-LZ10P/PC • c) DMC-LZ10E/EB/EF/EG/GN • d) DMC-LZ10EE • e) DMC-LZ10GK • f) DMC-LZ10PL/GC What is the difference is that the “INITIAL SETTINGS”...
Page 9
3.4.2. INITIAL SETTINGS: When you replace the Main PCB, be sure to perform the initial settings after achieving the adjustment by ordering the following pro- cedure in accordance with model suffix of the unit. 1. IMPORTANT NOTICE: Before proceeding Initial settings, be sure to read the following CAUTIONS. 2.
Page 10
• Step 5. Set the INITIAL SETTING: (Refer to “CAUTION 1”) [Caution for befor settings] Once "NONE(JAPAN)" (Area for Japan) or "P" (Area for Noth America) is selected with "INITIAL SETTINGS", other areas will not displayed even if "INITIAL SETTINGS" menu is displayed again, thus, the area can not be changed. Select the area carefully.
6 Service Mode 6.1. Error Code Memory Function 1. General description This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the latest. When the error is occurred more than 16, the oldest error is overwritten in sequence. The error code is not memorized when the power supply is shut down forcibly (when the unit is powered on by the battery, the battery is pulled out) because the error code is memorized to FLASH ROM when the unit is powered off.
Page 15
• 5. How to read the error code: One error code is displayed for 8 bit, the contents of error codes is indicated the table as shown below. Attribute Main item Sub item Error code Contents (Upper) High 4 bits Low 4 bits Check point (Lower) LENS Lens drive...
Page 16
Attribute Main item Sub item Error code Contents (Upper) High 4 bits Low 4 bits Check point (Lower) HARD VENUS A/D Flash 20*0 0000 Flash charging error. IC6001-(AC17) signal line or Flash charging circuit FLASH ROM FLASH ROM 2B*0 0001 EEPROM read error (EEPROM (EEPROM...
7.2. When Replacing the Main PCB After replacing the MAIN PCB, be sure to achieve adjustment. The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in “TSN system”, together with Maintenance software. 7.3. Service Position This Service Position is used for checking and replacing parts.
8.3. Disassembly Procedure 8.3.1. Removal of the Rear Case Unit Item Removal Rear Case Unit Fig. D1 Card Battery 5 Screws (A) FP9103(Flex) FP9004(Flex) 2 Locking tabs Rear Case Unit Fig. D2 NOTE: (When Installing) LCD Unit Fig. D3 1 Screw (B) LCD Holder LCD Unit SD Cover...
Page 21
8.3.2. Removal of the LCD Unit Fig. D2 Fig. D3...
Page 22
8.3.3. Removal of the SD Cover 8.3.4. Removal of the Front Case Unit Fig. D4 Fig. D5...
Page 23
8.3.5. Removal of the Top Case Unit 8.3.6. Removal of the Flash Top P.C.B. Fig. D6 Fig. D7...
Page 24
8.3.8. Removal of the Lens Unit Fig. D10 NOTE: (When Assembling) Be sure to confirm the following points when assembling. • The Screw is tightened enough. Fig. D8 • Assembling conditions are fine. (No distortion, no illegal- space.) 8.3.7. Removal of the Main P.C.B. •...
8.4. Disassembly Procedure for the Lens NOTE: When Disassembling and Assembling for the Lens 1. To minimize the possibility of the CCD being dirt, perform disassemble and/or assemble under the condition of the CCD is being mounted. Disassembling procedures for the CCD unit, refer to item 8.6.
Page 26
8.4.2. Removal of the Master Flange Unit 8.4.3. Removal of the 1st Lens Frame/2nd Lens Frame Move Unit 8.4.4. Removal of the 2nd Lens Frame Move Unit...
8.5. Assembly Procedure for the 8.5.2. Phase alignment of the Drive/Direct Unit and Fixed Frame Unit Lens 8.5.1. Phase alignment of the Direct Frame and Drive Frame Unit...
Page 28
8.5.3. Assembly for the 1st Lens Frame 8.5.4. Assembly for the 2nd Lens Frame Unit and Drive/Direct/Fixed Frame Move Unit and Drive/Direct/Fixed Unit Frame/1st Lens Frame Unit...
8.5.5. Assembly for the Master Flange 8.6. Removal of the CCD Unit Unit and Drive/Direct/Fixed Frame/ To prevent the CCD unit from catching the dust and dirt, do not 1st Lens Frame/2nd Lens Frame remove the CCD unit except for replacing. Move Unit...
8.7. Removal of the Focus Motor 8.8. Applyment Grease Unit Method The grease apply point of lens unit are as follows. Apply grease additionally in the specified position if necessary. When the grease is applied, use a toothpick and apply thinly. •...
9 Measurements and Adjustments 9.1. Matrix Chart for Replaced Part and Necessary Adjustment The relation between Replaced part and Necessary Adjustment is shown in the following table. When concerned part is replaced, be sure to achieve the necessary adjustment(s). As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software. The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website”...
10 Maintenace 10.1. Cleaning Lens and LCD Panel Do not touch the surface of lens and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface. Note: The Lens Cleaning KIT ;...
Page 33
DSC0802013CE S1. About Indication of The Schematic Diagram Service Manual S1.1. Important Safety Notice COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS Diagrams and Replacement FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE. 1.Although reference number of the parts is indicated on the P.C.B. drawing and/or Parts List schematic diagrams, it is NOT mounted on the P.C.B.
S2. Voltage Chart Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. S2.1.
S3. Block Diagram S3.1. Overall Block Diagram (30mm ~ 150mm) IC3001 PRE PROCESS X6001 (24MHz) 1/2.33" 10 MEGA PIX CDS, AGC, A/D, TG, CCD DRIVER ZOOM OIS UNIT IRIS SHUTTER FOCUS CARD IC9101 SYSTEM IC MOTOR DRIVE, OIS DRIVE& IC9101 MICROPHONE PRE PROCESS SYSTEM IC...
S4.4. Lens Flex Schematic Diagram POSITIVE VOLTAGE LINE COIL STEPPING FOCUS MOTOR UNIT MOTOR COIL ENC VCC LED CONT PHOTO CO. BARREL ENCODER XVO+ SENSOR (FULL RETRACT) XVH- HALL SENSOR (X) XVO- XVH+ OIS UNIT XDRV- DRIVE COIL (X) XDRV+ STAP STAP DC SOLENOID...
S6. Replacement Parts List Note: 1.* Be sure to make your orders of replacement parts according to this list. 2. IMPORTANT SAFETY NOTICE Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type. 3.
Page 44
DMC-LZ10P-S/K,PC-S/K,PL-S/K,EB-S/K,EE-S/K,EF-K,EG-K,E-S/K,GC-S/K,GK-S/K,GN-K Ref.No Part No. Part Name & Description Remarks Ref.No Part No. Part Name & Description Remarks ------ P.C.B. LIST ------ ## VEP58050A FLASH TOP P.C.B. 1 (RTL)E.S.D. ## VEK0L75 CCD UNIT 1 E.S.D.[PAVC-CSG] --- INDIVIDUAL PARTS --- C8003 F2A2F1510002 E.CAPACITOR --- ELEC.
Page 45
DMC-LZ10P-S/K,PC-S/K,PL-S/K,EB-S/K,EE-S/K,EF-K,EG-K,E-S/K,GC-S/K,GK-S/K,GN-K Ref.No Part No. Part Name & Description Remarks Ref.No Part No. Part Name & Description Remarks C8004 F1K2J102A010 C.CAPACITOR 630V 1000P C8005 F1J0J2260004 C.CAPACITOR CH 6.3V 22U C8006 F1K2E4730002 C.CAPACITOR 250V 0.047U C8009 F1J0J1060010 C.CAPACITOR CH 6.3V 10U D8001 B3ADB0000120 AF LED 1 E.S.D.
Page 46
DMC-LZ10P-S/K,PC-S/K,PL-S/K,EB-S/K,EE-S/K,EF-K,EG-K,E-S/K,GC-S/K,GK-S/K,GN-K Ref.No Part No. Part Name & Description Remarks Ref.No Part No. Part Name & Description Remarks VEP56055A MAIN P.C.B. 1 (RTL)E.S.D.(VEP56055C) VXW0911 LENS UNIT(W/O CCD) 1 [PAVC-CSG] [PAVC-CSG] VDL2046 OPTICAL FILTER 1 [PAVC-CSG] VEP56055C MAIN P.C.B. 1 (RTL)E.S.D.(VEP56055A) VEK0L75 CCD UNIT 1 [PAVC-CSG] ...
Page 47
DMC-LZ10P-S/K,PC-S/K,PL-S/K,EB-S/K,EE-S/K,EF-K,EG-K,E-S/K,GC-S/K,GK-S/K,GN-K Ref.No Part No. Part Name & Description Remarks Ref.No Part No. Part Name & Description Remarks VPK3548 PACKING CASE 1 P-S,PC-S VPF1301 CAMERA BAG (FOR MADE IN CHINA) K1HA08CD0007 USB CABLE W/PLUG VPK3420 PACKING CASE 1 P-S,PC-S [PAVC-CSG] K1HA08CD0008 AV CABLE W/PLUG (FOR MADE IN JAPAN) VFC4297-A HAND STRAP...