Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bissell 3 3 N 7
Summary of Contents for Bissell 3 3 N 7
- Page 1 Pet Hair Eraser Cyclonic Bagless Canister U S E R ’ S G U I D E 3 3 N 7 S E R I E S 2 2 0 - 2 4 0 V ™ Safety Instructions Product View...
- Page 2 Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL canister vacuum is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance.
-
Page 3: Important Safety Instructions
Bs 1362) fuse is fitted in the carrier contained in the plug. (spares may be obtained from your BIssell supplier). If for any reason the plug is cut off, it must be disposed of, as it is an electric shock... -
Page 4: Product View
roduct view Flex Hose Carry Handle Swivel Hose Easy Empty Dirt Cup Clean Filter Indicator Power Button Post-Motor HEPA Media Filter Upholstery Tool Crevice Tool Pet Contour Tool Wide Pet TurboBrush ™ w w w . b i s s e l l . c o m Handle Air Flow Regulator Dusting Brush... -
Page 5: A Ssembling Your Vacuum
ssembling your vacuum Connect swivel hose by squeezing both locking buttons and inserting it into the suction opening on the canister. Once the swivel hose is inserted in the suction opening, release the locking buttons. Connect telescoping extension wand to the handle end of the flex hose. Twist slightly to tighten. Connect Pet Hair Eraser floor nozzle to the end of the telescoping extension wand. Twist slightly to tighten. Once assembled, you can store your vacuum in one of two positions: a. Storing in the in-use position: 1. T o store with the Pet Hair Eraser floor nozzle attached, insert the storage clip (located on the back of the floor nozzle) into the storage slot on the rear of the vacuum. 2. T o store without the Pet Hair Eraser floor nozzle attached, insert the storage clip (located on the bottom of the telescoping extension wand) into the storage slot on the rear of the vacuum. b. Storing in the upright position: 1. T o store with the Pet Hair Eraser floor nozzle attached, stand the vacuum in the upright position and insert the storage clip (located on the back of the floor nozzle) into the storage slot on the bottom of the vacuum. 2. T o store without the Pet Hair Eraser floor nozzle attached, stand the vacuum in the upright position and insert the storage... -
Page 6: Power Button
perations Power button turn the power on or off by pressing lightly downward on the power button ( ). Power cord the power cord is located at the rear of the vacuum. Gently pull out the power cord, watching for the yellow line. Stop pulling the power cord once the yellow line is visible. -
Page 7: Special Tools
Special tools your bISSEll Pet Hair Eraser cyclonic bagless canister is not only a powerful carpet and rug vacuum cleaner, it’s also a versatile bare floor vacuum cleaner and above floor vacuum cleaner when you select one of the special tools. - Page 8 perations Pet Hair Eraser Floor Nozzle continued 1. To vacuum rugs and carpeted surfaces, flip down the Pet Hair Lifter until it clicks into place on the front of the Pet Hair Eraser Floor Nozzle. Then push the brush switch to the carpet position to pull the brushes up into the Pet Hair Eraser Floor Nozzle. 2. To vacuum bare floors, push the brush switch to the bare floor position to extend the brushes down from the Pet Hair Eraser Floor Nozzle. Then flip up the Pet Hair Lifter by pushing the yellow release button. This will flip the Pet Hair Lifter up and out of the way. Variable suction power control the variable suction power control is located on the back of the vacuum. turn the control toward the larger dots for maximum suction.
-
Page 9: Emptying The Dirt Cup
aintenance and care Emptying the dirt cup 1. Turn vacuum OFF ( ) unplug the vacuum from electrical outlet. 2. Open the dirt cup compartment by lifting up the door latch on the front of the vacuum. 3. Lift the dirt cup assembly out from the vacuum. 4. Remove the top cover from the dirt cup assembly by unfastening the latch, raising the front edge and removing the top cover from the rear hinges. Set the top cover aside. 5. Empty the dirt into a garbage container. 6. To reattach the top cover on the dirt cup, align the slots on the top cover with the hinges on the dirt cup and rotate the front cover down to the closed position. Then fasten the latch. 7. Place the dirt cup back into the vacuum. 8. Close dirt cup compartment door and press down gently until it locks into place. NotE: the compartment door will not close without the dirt cup in place. Cleaning the pre-motor filter the pre-motor filter protects the motor from dirt and dust particles. -
Page 10: Maintenance And Care
aintenance and care Replacing the post-motor HEPA media filter the post-motor HEPa media filter assists in the filtration process to return clean air to the room. 1. Turn vacuum OFF ( ) unplug the vacuum from electrical outlet. 2. Remove the filter door (located on the back of the vacuum) by pulling down on the filter door and pulling it toward you. 3. Remove the post-motor HEPA media filter by grasping the tabs of the filter frame and pulling out toward you. 4. Replace the post-motor HEPA media filter with a new filter. NotE: the post-motor filter is a white, pleated HEPa media filter. - Page 11 aintenance and care Replacing the dirt cup HEPA media & cleaning the foam filter continued 3. The dirt cup foam filter is located between the bottom of the dirt cup and the HEPA media filter. Once the HEPA media filter has been removed, the foam filter can then be removed and cleaned or replaced as needed. To clean the foam filter, wash with warm water and a mild detergent. Be sure to air dry completely before replacing this filter in the dirt cup. 4. To re-install the filters in the dirt cup, turn dirt cup upside down and replace the foam filter. Then replace the HEPA media filter by inserting the tabs on the back of the filter into the slots on the bottom of the dirt cup and snap the filter back into place. Clearing clogs from the dirt cup 1. To clear clogs from the dirt cup, remove the top cover and set aside.
- Page 12 aintenance and care Maintaining the Wide Pet TurboBrush the Wide Pet turbobrush should be checked regularly for clogs or debris wrapping around the brush. 1. Turn vacuum OFF ( ) unplug the vacuum from electrical outlet. 2. If a clog is present or debris is visible, turn the collar on the neck of the Wide Pet TurboBrush counterclockwise to the unlocked position to remove the faceplate and clear any obstructions. 3. To clean debris from the brush, remove the brush from the drive belt and clean debris. 4. Reposition the drive belt on the brush. Place the ends of the brush in the slots on the sides. Reposition the faceplate and turn the collar clockwise to the locked position.
-
Page 13: Troubleshooting
6. Crack or hole in flex hose other maintenance or service not included in the manual should be performed by an thank you for selecting a bISSEll product. Please do not return this product to the store. w w w . b i s s e l l . c o m... - Page 14 In the UK, Australia, New Zealand, the middle east or Africa, call BIssell Consumer services at the numbers below and we will give you the location of a BIssell Authorized service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair.
- Page 15 - BISSELL Pet Hair Eraser Cyclonic Bagless Canister Item Part No. 203-7289 203-7259 203-7258 203-7260 203-7261 203-7257 203-7256 203-7265 203-7266 203-7264 203-7275 203-7279 203-1291 203-1290 203-7278 w w w . b i s s e l l . c o m...
-
Page 16: Limited Two-Year Warranty
*eXCePTIoNs AND eXClUsIoNs identified below, BIssell homecare, Inc., will replace (with new or remanufactured components), at BIssell’s option, free of charge from the date of purchase by the original purchaser, for two years any defective or malfunctioning part do to manufacturers defect.