1. Manuals
  2. Brands
  3. Harbor Freight Tools Manuals
  4. Lifting Systems
  5. Haulmaster
  6. Owner's manual & safety instructions

Harbor Freight Tools Haulmaster Owner's Manual & Safety Instructions

Folding arched aluminium/steel ramps
Hide thumbs Also See for Haulmaster:
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the back
of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep
this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2021 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
21g

Advertisement

Table of Contents
loading

Related Manuals for Harbor Freight Tools Haulmaster

Summary of Contents for Harbor Freight Tools Haulmaster

  • Page 1 No portion of this manual or any artwork contained herein may be reproduced in Failure to do so can result in serious injury. any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing SAVE THIS MANUAL.

  • Page 2: Specifications

    Turn ramps so flange end faces If unreadable or missing, contact downward. Position ramps so that Harbor Freight Tools for a replacement. tongues fully contact tailgate. Clean Ramps. Prior to each use, h. Properly connect safety chains.
  • Page 3 13. Store idle equipment. broken parts or mounting fixtures and When not in use, store ramps in any other condition that may affect a dry location to inhibit rust. proper operation. Any part that is damaged should be properly repaired 14.
  • Page 4 Assembly Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. WARNING! TO PREVENT SERIOUS INJURY: In the following assembly process, the flange must face down with the Tongue edge fully contacting the tailgate.
  • Page 5 Note: Make sure Upper Ramp Connecting 10. Install Bolts, two Washers and Plates are on the Outside of Bottom Ramp Nuts into lower swivel mount holes, Connecting Plates. Refer to Figure A, connecting left Connecting Plates (6,7) and right Connect Upper Ramp to Bottom ramp. side Connecting Plates (4,5).
  • Page 6 Safety Strap Adjustment Loop the Safety Strap through Adjust the other Safety the anchoring point on the Strap to equal length. truck and hook it to itself. 4- Wheel ATV Loading and Unloading • These Ramps are for use with 2-wheeled dirt bikes and 4-wheeled ATV’s only. Do not use these Ramps to load/unload 3-wheeled vehicles.
  • Page 7 While staying off the ATV, start the engine, Release the brake and push on the ATV to disengage the parking brake, put the get it started down the Ramps. Allow the transmission into reverse, and make ATV to roll down naturally, do not steer it sure the wheels are in a straight line with or apply the brakes.

  • Page 8: Maintenance And Servicing

    Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY: Remove the Ramps from the vehicle before performing any maintenance or service. Do not use damaged equipment. If Ramps are damaged, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication BEFORE EACH USE, Clean the Ramps after each use.

  • Page 9: Please Read The Following Carefully

    PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.

  • Page 10: Parts List And Diagram

    Parts List and Diagram Parts List Part Description Part Description Bottom Ramp Connection Plate Upper Ramp Connection Plate Safety Strap Bolt Connection Plate Washer Connection Plate Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

  • Page 11: Assembly Diagram

    Assembly Diagram For technical questions, please call 1-888-866-5797. 63772 Page 11...
  • Page 12 Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents