Summary of Contents for Nebula TW62045
- Page 1 AHD LPR Camera OSD Manual TW62045 Thanks for purchasing our product. Before operating the unit, please read the instructions carefully and keep this manual for future reference.
- Page 2 Safety Warning 1. Read this manual carefully before installing the unit Please read this manual first for correct installation and operation. 2. Never install the camera on a ceiling that cannot hold its weight The product may fall down and cause damages. 3.
-
Page 3: Table Of Contents
Table of Contents CAMERA INSTALLATION ..........................3 1.1 I ....................3 NSTALL THE CAMERA TO THE FRONT OF THE VEHICLE 1.2 I ......................3 NSTALL THE CAMERA SLIGHTLY TO THE SIDE 1.3 M ..........................4 INIMUM IXELS EQUIREMENT 1.4 M ........................ -
Page 4: Camera Installation
1. CAMERA INSTALLATION 1.1 Install the camera to the front of the vehicle It’s strongly recommended to nstall the camera straight in front of and above the vehicle as shown below. A: The captured image should be filled with a full width of the vehicle. B: The distance between the vehicle and the camera should be within 2 to 18 meters;... -
Page 5: Minimum Pixels Requirement
1.3 Minimum Pixels Requirement Please make sure the captured license plate data is at least 120 pixels in width. 1.4 Minimum Shutter Speed Suggestion In general, it’s recommended to configure minimum shutter speed from 1/750 to 1/1000 for various mounting locations and scenarios. 1.5 Setting Focus for DAY/NIGHT Mode In order to make the most of LPR camera, we strongly suggest users set up/adjust the focus for DAY mode and Night mode separately. -
Page 6: Cable/Connector
B: Lighting. License plates are overexposed/interfered by the illumination of headlights or taillights. Try to use advanced/professional LPR cameras to avoid the glare or interference. 1.7 Cable/Connector ① Video Output For video signal output, it supports Control over Coaxial Cable technology. ②... -
Page 7: Camera Osd
2. CAMERA OSD To operate the camera OSD setting, use the control key pad to control it. For some models, you might need to open the control panel case to access the control key panel. Press the Enter button which in the center of the control panel to bring up the "MENU"... -
Page 8: Lens
2.2 LENS In the "LENS" page of the camera OSD, there are some items can be selected to modify the settings. Users can switch lens mode between AUTO IRIS and MANUAL and adjust the optical settings accordingly. AUTO IRIS LENS MANUAL LENS ■... -
Page 9: Lpr
2.3 LPR "LPR" (License Plate Recognition) have several items available for users to modify the advanced settings in collaboration with the previous LENS page. AUTO IRIS LENS MANUAL LENS ■ MODE: OUTDOOR/PARKING LOT is recommended to be set specifically based on the moving speed (KM/H) of the target as well as the outdoor/indoor location. - Page 10 AUTO SHUTTER (OUTDOOR) AUTO SHUTTER (PARKING LOT) MANUAL SHUTTER ■ SHUTTER: (MANUAL LENS) AUTO, MANUAL, 2 options available. The values of SHUTTER MIN/MAX speed for AUTO and MANUAL modes can be further adjusted as shown in the screenshots below. The defaults of SHTTER MIN/MAX are 1/30 and 1/30000 (subject to change by models) for AUTO SHUTTER;...
- Page 11 ■ SMART DET.: ■ DET DISP: To enable or disable the detection display function. Please see below for advanced settings. ■ AREA SEL: 4 areas are available as shown in the screenshot above. 1 refers to the upper left one, 2 is the upper right, 3 is the lower left and 4 is the lower right.
- Page 12 ■ CAR ALARM: To enable or disable the alarm function when a car is coming. ■ SENSITIVITY: To adjust the sensitivity for detection area level from 0 to 20. The bigger the number is set, the more sensitive the camera will be. ■...
-
Page 13: Hdr/Blc
HDR/BLC In the "HDR/BLC" of camera OSD, total 5 options are available and 4 of which have advanced settings menu for adjustment. Please see details below. ■ D-WDR: LEVEL can be adjusted among LOW/MIDDLE/HIGH. Default setting is MIDDLE. ■ HDR: To modify the WEIGHT value among LOW/MIDDLE/HIGH. -
Page 14: White Bal
2.5 WHITE BAL "WHITE BAL" (WHITE BALANCE): Total 4 options are available and 2 of which have advanced settings menu for adjustment. Please see details below. MANUAL PUSH LOCK ■ MANUAL: KELVIN: To adjust the KELVIN (Color temperature) value among LOW/MIDDLE/HIGH. R-GAIN: To adjust the R-GAIN (RED GAIN) value from 0 to 20. -
Page 15: Day/Night
2.7 DAY/NIGHT In the "DAY/NIGHT" of camera OSD, AUTO, IR SYNC or EXTERNAL, B/W, can be selected to modify the settings. Selecting COLOR will keep the camera in color display and B/W is on the contrary. IR SYNC or EXTERNAL makes the camera view synchronize with IR LED to switch COLOR or B/W based on the brightness of the environment. - Page 16 ■ IR OPTIMIZER: To adjust the IR Optimizer value to improve the image exposure issue when IR is turned on. The dark side of the image will also be optimized in terms of even brightness to enhance the effect as a whole.
-
Page 17: Image
2.8 IMAGE In the "IMAGE" of camera OSD, there are some items can be selected to modify the settings. The main function of this page is about the image settings. ■ SHARPNESS: To modify the value of sharpness. ■ SATURATION: To modify the value of saturation. -
Page 18: Effect
2.9 EFFECT In the "EFFECT" of camera OSD, there are some items can be selected to modify the settings. The main function of this page is about the camera effects. ■ PRIVACY: To enable the "privacy" effect or not. Enable this will go its sub-menu for privacy setting. Please check the details in its section. -
Page 19: Privacy
2.11 PRIVACY In the "PRIVACY" of camera OSD, please enable this function to enter and modify the settings. The main function of this page is about the privacy mask size and position. ■ ZONE NUM: To select number of zone for privacy mask from 1 to 16. ■... -
Page 20: System
2.12 SYSTEM In the "SYSTEM" of camera OSD, there are several sub-menus and items can be selected to modify the settings. The main function of this page is about the video format information and OSD firmware version. ■ DIGITAL OUT: To select the digital output setting between 1080P and 720P. - Page 21 COC: To enable or disable the function of Control over Coaxial cable. ■ CABLE LENGTH: To select the Transmission Distance from 0-200M or over 200M supported by the camera with Distance Compensation Setting. ■ COLORBAR: To enable or disable the mode of COLORBAR. ■...