Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Planet PedAlert 100
- Page 1 & ™ PedAlert Operator’s Manual © 1996 PLANET LLC, Patent #6,174,294, B1 Notice: The manufacturer reserves the right to make changes to the device and Operator’s Manual without obligation to notify any person or organization of the revision or change.
- Page 2 . PLANET LLC has enjoyed working with physical therapists and physicians to develop this simple but important biofeedback device for lower limb rehabilitation. PLANET is dedicated to providing advanced instrumented rehabilitation equipment to make clinical and related rehabilitation efforts more efficient and effective.
-
Page 3: Table Of Contents
Figure 6. A standard 9V battery is easily replaceable ----------9 Warning Read all directions before use! • PLANET LLC is NOT responsible for any damages that occur as a result of misuse of this device. • If the patient feels any pain or discomfort while using the device he/she should stop using the device immedi- ately and consult his/her physician. -
Page 4: General Information
• Sensor Sole • Warranty • Control Box • Optional Carrying Case • 9V Batter y (purchase through Planet Products 1-800-338-2010) Specificat ions Control Box Size: 3" X 2" X 1" (LxWxD) Weight: 12 ounces (with battery) Power Requirements: Standard 9V battery Weight Settings: Small - toe touch up to 75 lbs. -
Page 5: Operation
2. OPERATION To ensure best results in your use of PedAlert, follow these steps. 2. 1 Assemble the PedAlert. 2. 2 “Warm up” the device by stepping at least 25 times before calibration. 2. 3 Strap PedAlert over the patient’s shoe, cast, or prosthetic. -
Page 6: Figure 1. The Wire Needs To Be Firmly Connected
2.1. Assemble the PedAlert Make sure wiring is connected to control box shown in Figure 1. Attach control box to either side of the boot. Figure 1. The wire needs to be firmly connected for proper operation 2. Turn system ON using On/Off switch shown in Figure 2. The light will blink about once per second upon proper connection and adequate battery power levels. -
Page 7: Figure 3. Settings For The Force Monitor (Pedalert 120)
3. Turn down the weight threshold control until you hear the warning tone. Then set the volume level and check to assure the patient can hear the warning tone. Once the volume is set to an acceptable audible level, the patient should not lower the level. -
Page 8: Figure 4. User Must Assure Proper Placement Of Foot
3. Tighten Velcro™ straps. 4. Verify control box is securely attached. Refer to Figure 4. Figure 4. User must assure proper placement of foot in boot and securely attach electronics module to the boot pr ior to use. Helpful note for maximum accuracy •... -
Page 9: Figure 5. Adjusting The Force To Activate The Warning Tone
2.4. Set the Weight Threshold 1. The patient should step onto scale, gradually placing more weight until the prescribed weight threshold is met. 2. While holding the load at or below the prescribed weight threshold, set the weight threshold knob so the warning tone is activated. - Page 10 2.6. Operational Warnings If any of the following indications occur, see the Trouble- shooting Table on page 10. Red light not blinking. • Beeping about once per second. • Steady tone with no weight applied. • Warning Recalibration will be required if any of the following occurs: •...
-
Page 11: Maintenance And Troubleshooting
3. MAINTENANCE AND TROUBLESHOOTING The only maintenance needed for PedAlert is to keep the unit clean and occasionally to change the battery. 3.1. Keeping PedAlert Clean Wipe the cast boot and control box with a damp cloth, use a mild soap if necessary. 3.2. - Page 12 3.3. Troubleshooting Problem You should . . . Red light is not flashing 1. Check that power switch is on. 2. Check boot cable connections. 3. Check battery connections. 4. Battery may need replace- ment. Warning tone beeps on 1. Check battery and replace if and off repeatedly when necessary.