ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 1 из 24 ADJUSTMENT Service Mode Entering to Service Mode 1. Press button once on remote control. ↓ ↓ ↓ ↓ 2. Press button again and hold button down. ↓ ↓ ↓ ↓ Service Mode display 3.
Page 3
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 2 из 24 Displaying the Adjustment Menu Press MENU button on TV. Service Mode Press ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ Press Adjustment Mode Key Function in the Service Mode The following key entry during display of adjustment menu provides special functions. CAUTION: Never try to perform initialization unless you have changed the memory IC.
Page 4
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 3 из 24 Test signal selection Selection of the adjustment items PROGRAMME (on TV or remote control) Change of the data value Volume +/- (on TV or remote control) Adjustment menu mode ON/OFF MENU button (on TV) Initialization of the memory (IC510) "i+"...
Page 5
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 4 из 24 RCUT RED CUT GCUT GREEN CUT BCUT BLUE CUT RDRV RED DRIVE GDRV GREEN DRIVE BDRV BLUE DRIVE BRTC BRIGHTNESS CENTER COLC COLOR CENTER UVTT BASE BAND TINT CNTX CONTRAST MAX OPT1 TV SET OPTION 1 00F1 OPT2 TV SET OPTION 2...
Page 6
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 5 из 24 Enter Service Mode and select menu of TVOP by pressing P or P during display of adjustment menu. After selecting TVOP, press + or - to set I2C check function to disable or enable as below.
Page 7
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 6 из 24 Convert from Bit (Binary) to Hex The table for converting from bit (D7-D0) to hex (0x**). BIT (Binary) High nibble Low nibble file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.001\40L... 01.07.2015...
Page 8
3) Change ID data into MODEL ID to initialize by pressing + or -, refer to "MODEL ID TABLE". For example, if want to initialize 40LV685D, change MODEL ID into "0x3E". Note: MODEL ID is hex value. 4) Execute initialization of the memory.
Page 9
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 8 из 24 MODEL ID (HEX) Model name Panel vendor OPT4 Data (HEX) 0x3D 32LV685D/LV675D SAMSUNG 0x65 0x3E 40LV685D/LV675D SAMSUNG 0x6E 0xE5 32LV665D SAMSUNG 0x65 0xE6 40LV665D SAMSUNG 0x6E Initializing Data setting flowchart after replacing the Signal Unit...
Page 10
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 9 из 24 Picture Signal Red raster Green raster Blue raster All Black All White Self Diagnostic Function 1. Press "9" button on remote control during display of adjustment menu in the Service Mode. The diagnosis will begin to check if interface among IC's is executed properly. 2.
Page 11
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 10 из 24 TV CPU SW Version: Version information of TV Micro SW: Display 1 byte data. (Hex) EEPROM Version: Version information of TV Micro EEPROM: Display 1 byte data. (Hex) Power On Time: Total time the TV has been powered on. (Unit: Hours) (Decimal) Main PLL: Displays Data 11 - Data 18 (8 bytes) of tuner control data.
Page 12
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 11 из 24 Bus Errors: "none" is normal. Block: (SCART (FULL)) (SCART (S+AV)) (Composite) HDMI1 HDMI2 HDMI3 HDMI4 (Component) DTV DTV (Digital Only) Version Check Mode 1. Press "9" button twice on remote control during display of adjustment menu in the Service Mode.
Page 13
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 12 из 24 TV Model: TV Model ID: Boot Code Version: Core SW Version: Seine SW Version: TV Micro SW Version: Version information of TV Micro SW. Display 1 byte data. TV Micro EEPROM Version: Version information of EEPROM.
Page 14
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 13 из 24 A/D Adjust RGB: RGB (SCART or PC) input OK/NG/-- Same as "A/D Adjust COMP" Setting Hotel Mode Hotel Mode allows the customized settings for following hotel options according to various hotel requirements. Enable/Disable all Front Panel keys.
Page 15
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 14 из 24 1. By pressing P or P , following table data setting will change the value either 1 or 0 on selected items as follows; OPT2 OPT2 FUNCTION DESCRIPTION (Normal) D7 (bit7) Enable mode that TV standby will be Enable Disable...
Page 16
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 15 из 24 number will be appeared in forced when turn ON the main power D6 (bit6) ~ POS or VIDEO program number 0 ~ 127 [decimal] (Normal: 0) D0 (bit0) POS number: 0 ~ 99 VIDEO number: 100 ~ 127 (DTV = 100, VIDEO = 101, VIDEO = 102..)
Page 17
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 16 из 24 1. Press button once on remote control. ↓ ↓ ↓ ↓ 2. Press button again and hold button down. ↓ ↓ ↓ ↓ (Hotel Mode Settings menu) 3. While holding the button, press P button on TV set.
Page 18
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 17 из 24 5. Press buttons to select the item, and then press buttons to change the setting. 6. Press [Exit] button to finish Hotel Mode setting. Settings in "Hotel Mode Settings" menu Hotel Mode Corresponding Options Description...
Page 19
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 18 из 24 POS/VIDEO" is DTV Input 0x64 (ATV Input if DTV disabled) 101 ~ 108 External Inputs 0x65 101 (Video 1), 102 (Video 2), ...108 (PC) 0x6C Change Volume Off The last TV volume level remains OPT7, D7 not changed.
Page 20
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 19 из 24 Copying Hotel Mode Options via Hotel Clone Menu The following Hotel Mode Options can be copied to other same model TVs using USB Drive via Hotel Clone menu: OPT2 OPT6 OPT7 OPT8 VOLX DTV Channel Setup...
Page 21
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 20 из 24 ↓ ↓ ↓ ↓ b. Press button again and hold button down. ↓ ↓ ↓ ↓ (Hotel Clone menu display) c. While holding the button, press P button on TV set. 3.
Page 22
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 21 из 24 Loading the Hotel Mode Settings from USB Drive to TV 1. Enter Hotel Clone menu as shown in previous section. 2. Select "USB to TV" by pressing buttons. 3. Insert the USB drive carrying the copied settings, and press OK to copy settings to the 4.
Page 23
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 22 из 24 ProgrammeTimer LED Orange ON (solid) = The On timer is set. Red ON (solid) = The On timer is operating. LED Indication Condition Solution 1 PowerOn/Standby LED: BUS Error Turn OFF the TV and unplug the power Green blinks continuously.
Page 24
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 23 из 24 4. Highlight OK and press the OK key on the remote. 5. The status of the update is displayed during update. Never turn off the power while updating. 6. When the update is complete, the following message is displayed. 7.
Page 25
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 24 из 24 4. Press and hold the menu button on the control panel of the TV set. 5. Plug in the TV and watch the LEDs on the front of the TV set. a.
Стр. 1 из 2 FUNCTION AND OPERATION Remote Control Simple at-a-glance reference of your remote control. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.989\40L... 01.07.2015...
Page 27
Стр. 2 из 2 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.989\40L... 01.07.2015...
Page 28
Стр. 1 из 1 FUNCTION AND OPERATION TV Front and Side Panel Control A wide variety of external equipment can be connected to the input sockets on the side of the television. Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the television may be used for some functions.
Стр. 1 из 4 FUNCTION AND OPERATION Tuning the Television for the First Time Before switching on the television, put your decoder and media recorder, if applicable, to Standby. To set up the television, use the buttons on the remote control as detailed. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.437\40L...
Page 30
Стр. 2 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.437\40L... 01.07.2015...
Page 31
Стр. 3 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.437\40L... 01.07.2015...
Page 32
Стр. 4 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.437\40L... 01.07.2015...
Handling the LCD Module Стр. 1 из 4 SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 34
Handling the LCD Module Стр. 2 из 4 3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not remove the soiling, breathe on the surface and then wipe again. If the panel surface is extremely solied, use a CRT cleaner as a cleaner. Wipe off the panel surface by drop the cleaner on the cloth.
Page 35
Handling the LCD Module Стр. 3 из 4 6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground. 7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time.
Page 36
Handling the LCD Module Стр. 4 из 4 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.364\40L... 01.07.2015...
Стр. 1 из 1 PANEL IDENTIFICATION Panel Identification If the several panels are alternatively used in the same model without amending the model name, the identification marking will be shown at the last digit of the set serial number on the specification label on the back cover.
Page 38
U02A U01A POWER MAIN U03A AC SW U04B RMT U04A LED...
Стр. 1 из 4 SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
Page 40
Стр. 2 из 4 inflammability, voltage resistance, etc. therefore, use only replacement parts that have these same characteristics. Use only the specified parts when the mark is indicated in the circuit diagram or parts list. 7. Parts mounting and routing dressing of wirings should be the same as that used originally.
Page 41
Стр. 3 из 4 Resistance values in orms ( ). V: Voltmeter or oscilloscope (r.m.s. or peak reading) Input resistance : Input capacitance : 200 pF Frequency range : 15 Hz to 1 MHz and d.c. respectively Note: Appropriate measures should be taken to obtain the correct value in case of non sinusoidal waveforms.
Стр. 4 из 4 Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Стр. 1 из 2 SCHEMATIC DIAGRAM Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 55
Стр. 2 из 2 = Electrolytic capacitor = Mylar capacitor 3. The parts indicated with " " have special characteristics, and should be replaced with identical parts only. 4. Voltages read with DIGITAL MULTI-METER from point indicated to chassis ground, using a color bar signal with all controls at normal, line voltage at nominal AC volts.
Page 157
Стр. 1 из 32 PARTS LIST All Block Block : Block Location Parts No. Description U01AS MAIN (PE0719) U01AS 75016321 PC BOARD ASSY, PE0719C, MAIN U01AS MAIN (PE0719) B320 75011088 SCREW, SFS-4S-B1WM U01AS MAIN (PE0719) B321 75011088 SCREW, SFS-4S-B1WM U01AS MAIN (PE0719) C1000 75013662 CAPACITOR, CERA CHIP (1005), 25V JB 103K, C1005JB1E103KT...
Стр. 1 из 2 PARTS LIST Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" "PRODUCT SAFETY NOTICE". CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 190
Стр. 2 из 2 : Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.659\40L... 01.07.2015...