Samsung 6 Series Quick Setup Manual

Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1. Lift the cover on the back of the remote
upward as shown in the figure to the
right.
2. Install two AAA batteries.
✎
Make sure to match the + and -
ends of the batteries to the diagram
in the battery compartment.
3. Replace the cover.
Step 2
: Connect Power and Antenna or Cable
Step 3
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language, set
the clock mode, and launch the TV's channel memorizing process. It also displays
connection instructions similar to those in this guide.To navigate while Plug & Play
is running, press the Up, Down, Left or Right arrow buttons on your remote. To
make a selection, press the ENTERE button. To skip a screen, press the
button. To turn on your TV, press the
To run Plug & Play, follow these steps:
1
Using your remote control, select
the language for the On Screen
Display (OSD), and then press
ENTERE button.
2
Select Home Use, and then press
the ENTERE button. If you
select Store Demo, the TV will reset your picture and audio settings every 30
minutes.
3
Select Antenna Source. If Antenna Source is Air, Cable or Auto, you must
select your cable system type. After selecting source, select Search; then
press the ENTERE button on your remote.
✎
Most cable systems are Standard(STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4
The TV memorizes the available channels. This process can take up to 45
minutes.
All manuals and user guides at all-guides.com
VHF/UHF Antenna
Connect Ant In to
Antenna Cable
(Not Supplied)
• Wall cable jack
• VHF/UHF Antenna
or
• Cable or Satellite box
Ant or Cable Out
Use a 75 ohm (round) cable.
POWER button on the remote or on the TV.
Plug & Play
Select Language of the OSD.
English
Español
Menu Language :
Français
U Move E Enter
Step 4
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box
Use one of the connections below to connect your TV to an external A/V device.
We recommend using HDMI for the highest picture quality.
✎
When connecting to
AV IN 1 label. The jack will not match the color of the video cable (yellow).
Audio Cable (Not Supplied)
Video Cable (Not Supplied)
5
After the TV has memorized the channels, choose the Clock Mode. Select
Auto if you have a digital channel in your area. Select Manual if you don't, or
if you have a cable or satellite box. When done, press the ENTERE button.
✎
If you select Manual, the clock setting screen appears.
6
Select the daylight savings time setting: Off or On, and then press the
MENU
ENTERE button.
✎
This function is only available when the Clock Mode is set to Auto.
7
Select the time zone in which you live, and then press the ENTERE button.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
The Enjoy your TV. screen appears. Then press the ENTERE button.
Setting the Clock
Before you can use your TV's On/Off Timer, you must set the clock. To set the
clock, follow these steps:
1. Turn on your TV, press the
Time.
2. Select Clock Mode, and then press the ENTERE button.
3. Choose Auto or Manual.
x
If you select Auto, the current time will be set automatically using the time
from a digital channel.
x
If you select Manual, you can set the Month, Day, Year, Hour, Minute
and am/pm directly by pressing up, down, left and right arrow button on
your remote.
4. Press the RETURN
AV IN 1 on the back of your TV, attach the video cable (yell
Lowest Quality Connection
Audio/Video connection (480i only)
Using an Audio/Video Cable
DVD, Blu-ray player, cable box,
AUDIO OUT
STB satellite receiver, VCR
Device
VIDEO OUT
button on your remote, then select Setup →
MENU
button on your remote when done.