Download
Share
Print this page
Pitney Bowes SE-900-EI Operations & Parts Manual
  1. Manuals
  2. Brands
  3. Pitney Bowes Manuals
  4. Postal Equipment
  5. SE-900-EI
  6. Operations & parts manual
Pitney Bowes SE-900-EI Operations & Parts Manual

Pitney Bowes SE-900-EI Operations & Parts Manual

240 volts
Hide thumbs

Advertisement

Quick Links

Download this manual
SE-900-EI
240 VOLTS
Operation & Parts Manual

Advertisement

loading

Related Manuals for Pitney Bowes SE-900-EI

Summary of Contents for Pitney Bowes SE-900-EI

  • Page 1 SE-900-EI 240 VOLTS Operation & Parts Manual...
  • Page 2 Pitney Bowes Direct Mail Solutions SE 900 EI OWNERS MANUAL Table of Contents Installation guide Set-up instructions Operation instructions Cleaning Troubleshooting Parts manual Electrical schematic Warranty information...
  • Page 3 Pitney Bowes Direct Mail Solutions Section 1 Pitney Bowes DMS Installation Instructions 1. Before positioning the feeder on the inserter, follow the setup and operating instructions completely. When you are confident the material is feeding consistently, precede to the inserter preparation instructions then the installation and set-up procedure.
  • Page 4 Pitney Bowes Direct Mail Solutions Section 1 Pitney Bowes DMS Installation Instructions Cont’ 12. Position the feeder on the inserter table so that the edge of the leading piece is between the material guide tabs and the bottom of the front hopper plate.
  • Page 5 Pitney Bowes Direct Mail Solutions Section 2 Pitney Bowes DMS Set-up Instructions 1. With the feeder ON/OFF switch in the off position, loosen the two side guides and move them all the way to the sides of the feeder. Then loosen the rear guide ramp and move it all the way back out of the way.
  • Page 6 Pitney Bowes Direct Mail Solutions Section 2 10. BRIDGE TRAM PROCEDURE: It is critical to the performance of the feeder to have the separating wheels level with respect to the nip rollers. To do this, first loosen the bridge mounting screws (Item 10, Fig. 6-3) on both sides of the bridge.
  • Page 7 Pitney Bowes Direct Mail Solutions Section 3 Pitney Bowes DMS Operation Instructions 1. Adjust the 3-leg sensor arm to position the sensor 1/2” above the paper path and about 3/4 of the length of the piece ahead of the feeder.
  • Page 8 Pitney Bowes Direct Mail Solutions Section 4 Pitney Bowes DMS Cleaning Instructions Clean rollers and belts are very important to the performance of the feeder. Use a clean rag dampened with Isopropyl Rubbing alcohol, 70% by volume (typically available in drug stores) to clean belts and rollers. Do not use any other solvents, cleaners, or abrasive cleaners on the rollers or belts as they may damage the rubber.
  • Page 9 Pitney Bowes Direct Mail Solutions Section 5 Pitney Bowes DMS Troubleshooting Guide Problem Solution Feeder will not run. Check circuit breaker condition. Check outlet power source. Check power switch. Feeder runs but no material is being Check material supply. dispensed.
  • Page 10 Pitney Bowes Direct Mail Solutions Section 5 Pitney Bowes DMS Troubleshooting Guide Cont. Problem Solution Thin material does not feed. Adjust separation device as described in section 2. Remove material and fan the stack allowing air to separate the pieces.
  • Page 11 Pitney Bowes Direct Mail Solutions Section 6 Pitney Bowes DMS Parts Manual...
  • Page 12 Pitney Bowes Direct Mail Solutions Section 6 FEEDER ASSEMBLY (fig. 6-1) ITEM FIGURE QTY. DESCRIPTION SEPARATOR DEVICE ASSEMBLY SIDE GUIDE ASSEMBLY FRONT SHAFT ASSEMBLY NIP ROLLER SHAFT ASSEMBLY SUPPORT IDLER SHAFT ASSEMBLY DRIVE SHAFT ASSEMBLY CLUTCH SHAFT ASSEMBLY MOTOR ASSEMBLY...
  • Page 13 Pitney Bowes Direct Mail Solutions Section 6 FIG. 6-1...
  • Page 14 Pitney Bowes Direct Mail Solutions Section 6 SEPARATOR DEVICE ASSEMBLY (Fig. 6-2) ITEM PART NO. QTY. DESCRIPTION 10007-001 BLOCK, SEPARATOR, 3” ROLLER 10011-001 PLATE, MOTOR MOUNT (SEPARATOR) 10004-001 SHAFT, SEPARATOR 10005-003 SHROUD, SEPARATOR 99001-001 MOTOR, SEPARATOR 99002-001 PULLEY, 100MXL025 (NO HUB 3/8” B.) 99002-002 PULLEY, 16MXL025 (3/16”...
  • Page 15 Pitney Bowes Direct Mail Solutions Section 6 SEPARATOR DEVICE ASSEMBLY CONT’ (Fig. 6-2) SCREW, SET, 10-24 X 1/8” NOT SHOWN SCREW, SET, 10-24 X 3/8” (3” SEPERATOR WHEELS) SCREW, FLAT HD, 8-32 X 1/2 99003-017 WASHER, NYLON, 3/8 ID X 1/16...
  • Page 16 Pitney Bowes Direct Mail Solutions Section 6 FIG. 6-2...
  • Page 17 Pitney Bowes Direct Mail Solutions Section 6 SIDE GUIDE ASSEMBLY (fig. 6-3) ITEM PART NO. QTY. DESCRIPTION 10003-001 TIE BAR 10005-010 GUIDE, SIDE, RH 900EI (TALL) 10005-011 GUIDE, SIDE, LH 900EI (TALL) 10005-002 GUIDE, FRONT PAPER (TALL) 10007-010 BLOCK, SEPARATOR ADJUSTING 10009-002 BRACKET, SIDE GUIDE MTG.
  • Page 18 Pitney Bowes Direct Mail Solutions Section 6 FIG 6-3...
  • Page 19 PART NO. QTY. DESCRIPTION 10004-067 SHAFT, FRONT, SE-900-EI 10004-124 SHAFT, NIP ROLLER, 3/4 (900 EI) 10004-002 SHAFT, MAIN, SE-900-EI 10004-003 SHAFT, SUPPORT IDLER, SE-900-EI 10006-070 NIP ROLLER, 3/4 BORE 10006-071 PULLEY, MATE, 3/4 BORE 10006-014 PULLEY, CROWNED 10006-007 FEEDER, ROLLER 10006-012...
  • Page 20 Pitney Bowes Direct Mail Solutions Section 6 FIG. 6-4...
  • Page 21 Pitney Bowes Direct Mail Solutions Section 6 MOTOR / CLUTCH SHAFT ASSEMBLY (Fig. 6-5) ITEM PART NO. QTY. DESCRIPTION 10004-155 SHAFT, CLUTCH 99008-010 CLUTCH / BRAKE, 90 VOLTS 99001-003 MOTOR, 4Z142 10006-077 PULLEY, CLUTCH 36XL037 99002-004 PULLEY, 22XL037 99002-008 PULLEY, MOTOR 12XL037...
  • Page 22 Pitney Bowes Direct Mail Solutions Section 6 FIG. 6-5...
  • Page 23 Pitney Bowes Direct Mail Solutions Section 6 PAPER SLIDE ASSEMBLY (fig. 6-6) ITEM PART NO. QTY. DESCRIPTION 10009-003 BRACKET, PAPER SLIDE 10004-014 SHAFT, PAPER SLIDE 10005-016 SUPPORT, PAPER SLIDE 99022-001 RETAINING RING, 1/4" 99004-002 KNOB, #10 SCREW SCREW, SOCKET HD, 10-24 X 1/2...
  • Page 24 Pitney Bowes Direct Mail Solutions Section 6 FIG 6-6...
  • Page 25 Pitney Bowes Direct Mail Solutions Section 6 CHASSIS ASSEMBLY (Fig. 6-7) ITEM PART NO. QTY. DESCRIPTION 10000-002 SIDE FRAME, L.H. (900-EI) 10000-001 SIDE FRAME, R.H. (900-EI) 10001-001 COVER, TOP 10002-001 COVER, BOTTOM 99007-001 SUCTION CUP, FOOT NUT, HEX 8-32 WASHER, LOCK #8...
  • Page 26 Pitney Bowes Direct Mail Solutions Section 6 FIG. 6-7...
  • Page 27 Pitney Bowes Direct Mail Solutions Section 6 ELECTRICAL COMPONENT ASSEMBLY (Fig. 6-8) ITEM PART NO. QTY. DESCRIPTION 98000-001 SWITCH, POWER (RED ROCKER) 98004-002 CIRCUIT BREAKER, 1 AMP 98005-007 CONTROLLER, MOTOR, 240 V-AC W/ SPEED POT 98001-002 TERMINAL STRIP (12 CONNECTOR)
  • Page 28 Pitney Bowes Direct Mail Solutions Section 6 FIG. 6-8...
  • Page 29 Pitney Bowes Direct Mail Solutions Section 6 TRAILING ARM ASSEMBLY (Fig. 6-9) ITEM PART NO. QTY. DESCRIPTION 10011-002 ARM, TRAILER 10012-003 SPACER 10006-016 ROLLER 10004-007 WEIGHT (900 EI) SCREW, PAN HD 8/32 X 1-1/4 SCREW, PAN HD 8/32 X 3/8...
  • Page 30 Pitney Bowes Direct Mail Solutions FIG. 6-9...
  • Page 31 Pitney Bowes Direct Mail Solutions ATTACHMENT ASSEMBLY (Fig. 6-10) ITEM PART NO. QTY. DESCRIPTION FRONT PAPER GUIDE, SWING ARM INSERTER BACK PLATE, SWING ARM INSERTER 10017-001 PAPER KNOCKDOWN ASSY (900EI ATTACHMENT)
  • Page 32 Pitney Bowes Direct Mail Solutions FIG 6-10...
  • Page 33 Pitney Bowes Direct Mail Solutions PAPER KNOCKDOWN ASSEMBLY (Fig. 6-11) ITEM PART NO. QTY. DESCRIPTION 10009-021 BRACKET, KNOCKDOWN 10007-019 BLOCK, KNOCKDOWN CLAMP 99004-002 KNOB, #10 SCREW 99004-016 KNOB, #8 SCREW 10005-040 GUIDE, SPRING STEEL SCREW, SKT HD, 10-24 X 1/2...
  • Page 34 Pitney Bowes Direct Mail Solutions FIG. 6-11...
  • Page 35 Pitney Bowes Direct Mail Solutions Section 7 Pitney Bowes DMS SE 900 EI Electrical Schematic...
  • Page 36 Pitney Bowes Direct Mail Solutions Section 8 900 EI...
  • Page 37 Pitney Bowes DMS who will determine a time to have the feeder inspected in the field by a representative of Pitney Bowes DMS or returned to Pitney Bowes DMS corporate headquarters.